Einleitung

Disassembling Sony Cybershot DSC-W5 in order to get to the battery terminal so that it can be replaced.

Ersatzteile

Kein Ersatzteil erforderlich.

Remove Memory Stick Pro from the card reader slot on the bottom of the camera.
  • Remove Memory Stick Pro from the card reader slot on the bottom of the camera.

  • Remove both batteries.

Kommentar hinzufügen

Remove the single visible screw from both sides of the camera.
  • Remove the single visible screw from both sides of the camera.

  • Remove the two screws that are adjacent to the warning label, which is on the underside of the camera.

  • Do NOT remove all four screws from the bottom.

Kommentar hinzufügen

  • Gently remove the back cover from the camera.

  • The first time the case is removed, it will be stiff. Be patient and gently rock the cover back and forth until it slides free.

Kommentar hinzufügen

  • Remove the two screws holding the circuit board down.

Kommentar hinzufügen

  • Detach the orange cable from the board.

  • Use a thin object, like a paperclip, to gently pry the cable off the connector.

Kommentar hinzufügen

  • The LCD screen sits in two slots; one on the bottom, and one on the left edge.

  • Slide LCD screen from the two slots.

  • Do not attempt to completely remove the screen, as it is still attached to the camera.

Kommentar hinzufügen

  • To remove the LCD screen, detach the orange cable from the board.

  • If needed, replace the LCD screen.

Kommentar hinzufügen

  • Remove the two screws holding down the steel back plate.

  • Remove steel back plate.

Kommentar hinzufügen

  • Now remove the plastic plate that covers the motherboard.

Below and to the left of the viewfinder there is a vertical slot in the motherboard with a soldered connection to the flash capacitor on each side. Using a small screwdriver with an INSULATED handle, short these together for several seconds to discharge the potentially dangerous charge.

Philip Le Riche - Antwort

  • Warning: Electric Shock From this point on, hold the camera by the chrome edges ONLY. Capacitors store electric charge even if the batteries are removed.

  • Remove the blue cable.

Kommentar hinzufügen

  • Disconnect the flash cable (black and white wires) before completely removing the front case.

  • Gently start to remove the case.

  • Once the cable is free, set aside the front case.

If the front doesn't seem to want to come away, maybe the flash cable is caught around its socket.

Philip Le Riche - Antwort

  • The speaker should now be clearly seen on the underside of the camera.

  • Gently unplug the speaker from the motherboard.

  • Replace the speaker.

Kommentar hinzufügen

  • Remove the orange cable connecting the battery terminal to the motherboard.

Kommentar hinzufügen

  • The battery terminal is now free from the board and can be slid out.

Kommentar hinzufügen

Abschluss

To reassemble your device, follow these instructions in reverse order.

4 weitere Nutzer haben diese Anleitung absolviert.

Thomas

Mitglied seit 14.04.2010

109 Reputation

6 Anleitungen geschrieben

Team

Cal Poly, Team 15-50, Garner Spring 2010 Mitglied von Cal Poly, Team 15-50, Garner Spring 2010

CPSU-GARNER-S10S15G50

5 Mitglieder

6 Anleitungen geschrieben

Clean the little nobs in the pattery-pack and problem solved! I also removed the black plastic ring that was on the +pole inside.

martinenjellie - Antwort

Kommentar hinzufügen

Statistik anzeigen:

Letzte 24 Stunden: 3

Letzte 7 Tage: 21

Letzte 30 Tage: 74

Insgesamt: 12,790