Zum Hauptinhalt wechseln

Diese Version enthält möglicherweise inkorrekte Änderungen. Wechsle zur letzten geprüften Version.

Was du brauchst

  1. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 1, Bild 1 von 2 : Schritt 1, Bild 2 von 2
    • We need to turn off the camera because we are removing components that could get damaged if the power is still on.

    • If the camera is on, rotate the power switch on top of the camera counterclockwise to turn the camera off.

  2. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 2, Bild 1 von 1
    • Flip the camera over such that the power switch points down.

    • Slide the switch on the bottom of the camera grip towards the lens to open the battery door.

  3. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 3, Bild 1 von 1
    • With the battery door open, push the blue lever in the battery compartment to release the battery.

  4. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 4, Bild 1 von 1
    • To the left of the battery compartment, the SD card needs to be pushed down slightly with your fingers, which will cause the card to eject.

    • Pull the card out with your fingers.

  5. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 5, Bild 1 von 2 : Schritt 5, Bild 2 von 2
    • First, turn the camera upside down.

    • Press the button located next to silver lens mount and rotate the lens counterclockwise.

    • Pull the lens away from the camera body.

    • After removing the lens, replace the lens or attach the body cap as soon as possible to prevent damage to the shutter.

  6. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 6, Bild 1 von 1
    • With the front of the camera facing you, remove the four silver #00 Phillips screws from the metal lens mount.

  7. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 7, Bild 1 von 1
    • Remove these three layers from the lens mount with your finger or by turning the camera face down.

  8. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 8, Bild 1 von 1
    • Remove the two newly visible #00 screws within the metal ring.

  9. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 9, Bild 1 von 1
    • Remove the final metal ring from the mount.

Ziellinie

5 weitere Nutzer:innen haben diese Anleitung absolviert.

Jay Miley

Mitglied seit: 04/22/14

5.052 Reputation

13 Anleitungen geschrieben

Team

Cal Poly, Team 10-55, Amido Spring 2014 Mitglied von Cal Poly, Team 10-55, Amido Spring 2014

CPSU-AMIDO-S14S10G55

4 Mitglieder

31 Anleitungen geschrieben

0 Kommentare

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 0

Letzte 7 Tage: 4

Letzte 30 Tage: 17

Insgesamt: 2,206