Zum Hauptinhalt wechseln

Diese Version enthält möglicherweise inkorrekte Änderungen. Wechsle zur letzten geprüften Version.

Was du brauchst

  1. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 1, Bild 1 von 1
    • Set the computer display-side down.

    • Unlock the battery by sliding the port-side latch to the 'unlock' position.

  2. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 2, Bild 1 von 1
    • On the opposite side of the battery, press the release latch and slide the battery away from the main body to remove.

  3. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 3, Bild 1 von 1
    • Ignore the removal of the heat sink and memory panels as depicted. They do not need to be removed for the completion of this guide.

    • Remove the Torx security screw near the center of the battery-side edge.

  4. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 4, Bild 1 von 2 : Schritt 4, Bild 2 von 2
    • Press the tabs on each side of the display-side of the keyboard with the flat edge of a spudger.

    • Pull the keyboard toward the mouse pad and gently lift up.

  5. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 5, Bild 1 von 2 : Schritt 5, Bild 2 von 2
    • The keyboard is still attached by ribbon cable, don't try to remove the keyboard entirely yet.

    • Disconnect the ribbon cable by pressing the tabs on either side of the connector. Pull the cable out parallel to the connector.

    • Remove the keyboard.

  6. : Schritt 6, Bild 1 von 1
    • Lege den Laptop auf den geschlossenen Displaydeckel.

    • Entferne die drei Schrauben von der vorderen Handballenauflage auf der Unterseite des Laptops.

    • Drehe den Laptop vorsichtig um. Entferne drei weitere Schrauben von der Oberseite, die das Panel sichern. Ein Flachbandkabel ist immer noch am Panel befestigt, wenn du es entfernst.

  7. : Schritt 7, Bild 1 von 2 : Schritt 7, Bild 2 von 2
    • Hebe die Mausbaugruppe gerade soweit an, dass du auf das darunterliegende Verbindungskabel zugreifen kannst.

    • Hebe die Flachbandkabelsperre an, um das Kabel zu entfernen.

    • Entferne vorsichtig die Mauspanel-Baugruppe und lege sie beiseite.

  8. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 8, Bild 1 von 3 : Schritt 8, Bild 2 von 3 : Schritt 8, Bild 3 von 3
    • Remove the four screws from the underside of the computer. These screws are located underneath where the battery sits and secure the top keyboard panel.

    • To remove the panel below the screen, press up on the two tabs holding the panel in and lift up. The panel should pop off.

    • Before proceeding, remove all black tape holding down wires and other cabling.

  9. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 9, Bild 1 von 1
    In diesem Schritt verwendetes Werkzeug:
    Tweezers
    $4.99
    Kaufen
    • Pop off the antenna using a pair of tweezers.

  10. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 10, Bild 1 von 1
    • Remove the seven philips screws holding the speaker assembly in place.

    • Before removing the assembly, disconnect the ribbon cable located at the top left corner of the assembly.

    • The speaker assembly will come off with the display assembly.

Ziellinie

Ein:e weitere:r Nutzer:in hat diese Anleitung absolviert.

Ryan

Mitglied seit: 04/11/10

154 Reputation

2 Anleitungen geschrieben

Team

Cal Poly, Team 25-89, Amido Spring 2010 Mitglied von Cal Poly, Team 25-89, Amido Spring 2010

CPSU-AMIDO-S10S25G89

4 Mitglieder

63 Anleitungen geschrieben

0 Kommentare

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 0

Letzte 7 Tage: 1

Letzte 30 Tage: 15

Insgesamt: 4,403