Einleitung

This guide will show you how to replace the LCD display touchscreen digitizer for your Sony Xperia XA1 Ultra if the display is cracked or unresponsive. A heat gun or hairdryer is needed to open the back panel, which can become hot and potentially damage the phone. In addition, a T5 screwdriver is needed to remove screws, while tweezers and a spudger are needed to remove different components of the phone.

  1. Wedge your finger under the bottom ridge of the SD card insert.
    • Wedge your finger under the bottom ridge of the SD card insert.

    • Pull outwards with your fingers to remove the SD card from the left side of device.

  2. Use a hair dryer to heat each corner of the phone.
    • Use a hair dryer to heat each corner of the phone.

    • Alternate heating each corner for a minute to loosen the adhesive binding the back cover to the phone.

    • Don't heat one area for too long; the phone may get damaged from overheating.

    • Press a suction cup on a heated corner of the device.

    • Hold the phone down and gently lift the suction cup to create a small gap.

    • You may hear crunching or popping sounds when you lift up the back cover.

    • Insert your iFixit Opening Tool in the small gap between your phone and the back cover.

    • Lift up on the iFixit Opening Tool and insert your plastic card in the small gap between your phone and the back cover.

    • Slide your plastic card along the side of your phone to loosen the adhesive.

    • Move the card along the sides of the phone to lift all of the corners.

    • Lift up the back cover by lifting up the sides of the phone with your hand.

    • Apply a new strip of adhesive for reassembly.

    • Peel off the two pieces of black tape covering the battery with your hands.

    • Use the iFixit Opening Tool to remove the flexible orange strip which connects the battery to the motherboard.

    • Wedge the iFixit Opening Tool underneath the battery.

    • Remove the battery by pulling up on the iFixit Opening Tool.

    • Remove the four 4mm T5 screws on the top of the black panel securing the antenna module to the device.

    • Insert your iFixit Opening Tool underneath the antenna module.

    • Lift up gently with the iFixit Opening Tool to remove the antenna module.

    • The antenna module may be difficult to remove.

    • Insert your iFixit Opening Tool underneath the front camera and gently lift up.

    • Remove the front camera by lifting the front camera up with your hands.

    • Remove the 4mm T5 screw connecting the headphone jack to the panel.

    • Use your iFixit Opening Tool to lift and disconnect the headphone jack connector piece.

    • The small black piece connected to the headphone jack that is holding the single screw in place has broken off in the device shown.

    • Insert your iFixit Opening Tool between the back camera and the motherboard and gently lift up.

    • Lift up with the iFixit Opening Tool until the back camera is removed from the device.

    • Remove the two 4mm T5 screws connecting the motherboard to the device.

    • Use your flat head tweezers to remove the black wire connected to the motherboard.

    • Use your flat head tweezers to remove the white wire connected to the motherboard.

    • There are only two wires connected to the motherboard.

    • Use your iFixit Opening Tool to remove the main flex (the middle orange tab) from the motherboard.

    • Use your iFixit Opening Tool to remove the power button flex (the left orange tab) from the motherboard.

    • Wedge your iFixit opening tool under the motherboard.

    • Lift up with your iFixit Opening Tool to lift the motherboard from the device.

    • Wedge your flathead tweezers under the earpiece.

    • Lift up with your flat head tweezers to remove the earpiece from the device.

    • Wedge your flathead tweezers under the flashlight module.

    • Lift up with your flat head tweezers to remove the flashlight module from your device.

    • Grab the power flex from the charging port PCB board with your flathead tweezers.

    • Lift up with your flathead tweezers to remove the power flex from the charging port PCB board.

    • Grab the vibration motor connected to the charging port PCB board with your flathead tweezers.

    • Lift up with your flathead tweezers to remove the vibration motor.

    • Grab the black wire connected to the charging port PCB board with your flathead tweezers.

    • Pull up on the black wire with your flathead tweezers to disconnect the black wire from the charging port PCB board.

    • Grab the white wire connected to the charging port PCB board using your flathead tweezers.

    • Pull up on the white wire with your flathead tweezers to disconnect the white wire from the charging port PCB board.

    • Wedge your iFixit Opening Tool under the charging port PCB board.

    • Pull up with your iFixit Opening Tool to remove the charging port PCB board.

    • Remove the five 4mm T5 screws connecting the side panel to the power button flex cable.

    • Use your hands to grab the side panel of the device.

    • Pull your hands away from the device to remove the side panel.

    • Remove the five 4mm T5 screws connecting the SD card side panel to the device.

    • Remove the SD card side panel from the device by grabbing the SD card side panel with your hands and sliding the SD card side panel away from the device.

    • Grab the two pieces of black tape holding down the battery with your hands.

    • Lift up with your hands to remove the two black pieces of tape that hold down the battery.

    • Peel off the power button flex with your hands.

    • Remove the white wire from the device using your hands.

    • Remove the black wire from the device using your hands.

    • The LCD Display Touch Screen Digitizer should be the only part left.

Abschluss

To reassemble your device, follow these instructions in reverse order.

4 weitere Nutzer haben diese Anleitung absolviert.

Jacob Jung

Mitglied seit 18.04.2018

1.225 Reputation

9 Anleitungen geschrieben

Team

Cal Poly, Team S16-G3, Livingston Spring 2018 Mitglied von Cal Poly, Team S16-G3, Livingston Spring 2018

CPSU-LIVINGSTON-S18S16G3

4 Mitglieder

9 Anleitungen geschrieben

Thanks for the help! Any chance you know where to get the side panels/bars? searched everywhere and cant find them

Taken Out - Antwort

Statistik anzeigen:

Letzte 24 Stunden: 6

Letzte 7 Tage: 49

Letzte 30 Tage: 189

Insgesamt: 1,325