Sony Xperia Z Ultra Motherboard Replacement

Einleitung

Does your power button not respond? Does your screen remain off even after you press the power button many times? Replacing the motherboard may solve these problems.

Was du brauchst

Schritt 1 Battery

Sony Xperia Z Ultra Motherboard Replacement, Battery: Schritt 1, Bild 1 von 1

Use the small suction cup to lift the back panel:
Press the small suction cup on to the middle of the back panel.

Bearbeiten

Schritt 2

While holding the Sony Xperia Z ultra down with your left hand, slightly pull the small suction cup upwards to create a small opening between the back panel and the front panel.
While continuing to pull the small suction cup upwards, insert the spudger in the small opening.
Pry the front panel downwards with the spudger while continuing to pull the small suction cup upwards.

Bearbeiten

Schritt 3

Remove the back panel by pulling the small suction cup upwards.

Bearbeiten

Schritt 4

Remove the following six screws with a Phillips #000 screwdriver:
five silver 2.1 mm screws
one gold 3.1 mm screw

Bearbeiten

Schritt 5

Pry the plastic motherboard shield open by placing the spudger under the shield and running it along the edges.

Bearbeiten

Schritt 6

Use care to remove the motherboard shield, as it may break. The motherboard shield is made of a very thin plastic.
Remove the motherboard shield by lifting the lower end upwards first.

Bearbeiten

Schritt 7

Detach the battery connection cable by prying it upward with the spudger.

Bearbeiten

Schritt 8

Pry the upper end of the antenna upwards with the spudger.

Bearbeiten

Schritt 9

Detach the antenna by pulling the upper end upwards and outwards.

Bearbeiten

Schritt 10

Insert the spudger underneath the battery and run it back and forth to remove any adhesive.

Bearbeiten

Schritt 11

Remove the battery from the phone.

Bearbeiten

Schritt 12 Motherboard

Sony Xperia Z Ultra Motherboard Replacement, Motherboard: Schritt 12, Bild 1 von 1

Pry the antenna assembly upwards with the spudger.

Bearbeiten

Schritt 13

You should hear a slight "click" when the antenna assembly has been completely loosened.
Remove the antenna assembly by pulling it upwards from the right end.

Bearbeiten

Schritt 14

Remove the mic cover by placing the spudger underneath the cover and prying it upward.

Bearbeiten

Schritt 15

The metal shield is very thin, so use care to remove the metal shield as it can easily be bent.
Remove the metal shield cover by prying its right end upwards with the flat part of the spudger.

Bearbeiten

Schritt 16

Remove the mic connection from the motherboard ribbon by prying it upwards with the spudger.
Once released, the orange ribbon will resemble a flap.

Bearbeiten

Schritt 17

Use care to remove the black plastic spacer, as it may bend if excessive force is used. The black plastic spacer is very thin and extremely fragile.
Gently pry the black plastic spacer upwards with the spudger.
Remove the black plastic spacer from the phone by gently pulling it upwards.

Bearbeiten

Schritt 18

Release the LCD digitizer connection by prying it upwards with the spudger.
The LCD digitizer is distinguished by a longer connection strip.

Bearbeiten

Schritt 19

Use care to detach the vibration motor connection, as it may break if excessive pressure is applied. The vibration motor connection is tiny and fragile.
Use the flat part of a spudger to detach the vibration motor connection. It is a tiny white box with red and black wires leading to the motor.
Once the connection has been removed, slide the spudger underneath the vibration motor to release it from the adhesive.

Bearbeiten

Schritt 20

Remove the loudspeaker connection by prying it upwards with the spudger.

Bearbeiten

Schritt 21

Remove the orange ribbon connection by prying it upwards with the spudger.

Bearbeiten

Schritt 22

Pry the small black metal bracket off with the spudger.
Gently remove the ribbons that are attached to the side of the phone to avoid cracking them.
Remove the small black metal bracket by lifting it upwards and outwards.

Bearbeiten

Schritt 23

Detach the orange ribbon by wedging the spudger between the phone's casing and the ribbon. This will help prevent damage to the strip.

Bearbeiten

Schritt 24

Detach smaller orange ribbon by wedging the spudger between the phone's casing and the ribbon. This will help prevent damage to the strip.

Bearbeiten

Schritt 25

All parts connected to the motherboard with an orange ribbon are fragile and should be treated with extreme care.
Pry up the connection strip at the end of the motherboard using the flat part of the spudger to free the motherboard.
The connection strip has adhesive underneath.

Bearbeiten

Schritt 26

Manually remove the copper tape anchoring the motherboard's black ribbon.
When removing the motherboard in its entirety, make sure all securing points have been released.

Bearbeiten