Zum Hauptinhalt wechseln

SwagTron T1 Gyroscope Replacement

Was du brauchst

  1. SwagTron T1 Gyroscope Replacement, Back Panels: Schritt 1, Bild 1 von 1
    • Ensure that the SwagTron is off.

    • Turn the SwagTron upside down to see the underside.

  2. SwagTron T1 Gyroscope Replacement: Schritt 2, Bild 1 von 3 SwagTron T1 Gyroscope Replacement: Schritt 2, Bild 2 von 3 SwagTron T1 Gyroscope Replacement: Schritt 2, Bild 3 von 3
    • Unscrew the eighteen 10mm screws that secure the back panels using a Phillips #2 screwdriver.

    • The screws are tightly in place. It will take effort to screw them out.

    • The panel is still attached to the SwagTron by wires that go to the motherboard.

    • Carefully lift the panels off

    The panels don’t come off after removing the screws. Could they be also glued in place?

    uygar_selman - Antwort

    Same issue here with the T882. Resorted to trying to pry the shell off but haven’t been able to yet. The closer I get to the center, the harder it is.

    Victoria Milhoan - Antwort

    FYI - there are stickers over two of the screws (one on each side). Once the stickers are removed, and the screws taken out, the shell came off easily.

    Victoria Milhoan - Antwort

    THANK YOU! The screws were under the stickers near the center.

    Liz Vance -

    I removed all the screws from the panel, and I am pulling and tugging and I can only get one side loose but not the other. Anyone else experience this?

    MS R - Antwort

  3. SwagTron T1 Gyroscope Replacement: Schritt 3, Bild 1 von 3 SwagTron T1 Gyroscope Replacement: Schritt 3, Bild 2 von 3 SwagTron T1 Gyroscope Replacement: Schritt 3, Bild 3 von 3
    • Follow the wires from the panels to the motherboard.

    • You may need to cut any zip ties that are holding the wires together.

    • There is one connection on the battery side and three on the other side that must be removed.

    • These connections may be difficult to remove. Try to securely press the connection and pull firmly.

    • Your back panels are now completely removed.

    Where can I buy the shell

    Julio Barahona - Antwort

    Where can I buy the battery?

    Daniel O'Brien - Antwort

  4. SwagTron T1 Gyroscope Replacement, Gyroscope: Schritt 4, Bild 1 von 2 SwagTron T1 Gyroscope Replacement, Gyroscope: Schritt 4, Bild 2 von 2
    • Disconnect the gyroscope by disconnecting the wires attached to it. These wires are black, green, blue and red.

  5. SwagTron T1 Gyroscope Replacement: Schritt 5, Bild 1 von 1
    • Using your Phillips #2 screwdriver, remove the four 8mm screws marked in red from the gyroscope.

  6. SwagTron T1 Gyroscope Replacement: Schritt 6, Bild 1 von 3 SwagTron T1 Gyroscope Replacement: Schritt 6, Bild 2 von 3 SwagTron T1 Gyroscope Replacement: Schritt 6, Bild 3 von 3
    • Carefully remove the gyroscope component from the SwagTron.

Abschluss

To reassemble your device, follow these instructions in reverse order.

9 weitere Nutzer:innen haben diese Anleitung absolviert.

Teagan Allen

Mitglied seit: 04/18/17

426 Reputation

2 Anleitungen geschrieben

Team

Cal Poly, Team S17-G5, Banghart Spring 2017 Mitglied von Cal Poly, Team S17-G5, Banghart Spring 2017

CPSU-BANGHART-S17S17G5

4 Mitglieder

5 Anleitungen geschrieben

5 Kommentare

I cannot find a Swagtron T1 replacement gyroscope anywhere on the internet. Any help would be extremely appreciated!! Thank you!

Gavin Hosler - Antwort

Amazon.com Keyword: CertiCable

Jesse Griffis -

Where do you get the replacement?

Brittany Conner - Antwort

Can’t find gyroscope for a t5 hover board please help.

jbswearingen70739 - Antwort

I just got mine today and after the first hour I ran into a shoe and then I tried recalibrating it but it was no use. If someone knows what’s going on please tell me! Thank you :)

Elia Leon - Antwort

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 1

Letzte 7 Tage: 13

Letzte 30 Tage: 39

Insgesamt: 7,207