Einleitung

Follow this guide to remove the pump rod in a Tara pump for replacement or repair.

Werkzeuge

Kein Werkzeug erforderlich.

Ersatzteile

Kein Ersatzteil erforderlich.

  1. Before performing any repairs, perform a water test on the pump by raising and lowering the handle a full 40 strokes. A properly performing pump will yield greater than 10 liters.
    • Before performing any repairs, perform a water test on the pump by raising and lowering the handle a full 40 strokes. A properly performing pump will yield greater than 10 liters.

    • Use a Tara tool to loosen the jam nuts on either side of the pump.

    • The bolts do not need to be loosened or removed, only the nuts need to be loosened.

    Kommentar hinzufügen

  2. Unscrew the lock bolts about half an inch.
    • Unscrew the lock bolts about half an inch.

      • The bolts do not need to be removed from the base.

    Kommentar hinzufügen

    • Pull the plastic bushing and handle straight up out of the pump.

      • If the bushing doesn't come up, loosen the lock bolts further.

    Kommentar hinzufügen

    • Lift up the handle and riser main until the joint between the two is at a comfortable height to work on.

    Kommentar hinzufügen

    • Loosen the jam nut beneath the pump handle using the Tara tool.

    Kommentar hinzufügen

    • Unscrew the pump handle from the top of the riser main.

    • Make sure someone is tightly holding the lower portion of the riser main to prevent losing it down the well.

    Kommentar hinzufügen

    • Lift and remove the handle from the pump. Store the handle in a sanitary place to prevent contamination.

    Kommentar hinzufügen

    • Screw the T-handle onto the top of the riser main.

    Kommentar hinzufügen

  3. Frohes Fest, frohes Tüfteln!
    Satte 12 € Rabatt auf jeden Einkauf ab 50 €. Einfach den Code FIXMAS12 am Ende deines Bestellvorgangs eingeben
    Frohes Fest, frohes Tüfteln!
    Satte 12 € Rabatt auf jeden Einkauf ab 50 €. Einfach den Code FIXMAS12 am Ende deines Bestellvorgangs eingeben
    • Tighten the jam nut up against the base of the T-handle.

    Kommentar hinzufügen

    • Use the T-handle to push the riser main back down into the well.

    Kommentar hinzufügen

    • Once the riser main hits the bottom, turn the T-handle while pushing down.

    • This will hook the foot valve onto the traveling valve, allowing you to pull the two out of the well together.

    • You should feel some resistance if the foot valve is successfully attached.

    Kommentar hinzufügen

    • Use the T-handle to pull the riser main straight up out of the well.

    • Take care to pull up slowly to ensure the foot valve does not get released from the hook at the end of the riser main.

    Kommentar hinzufügen

    • Continue pulling the riser main up from the well.

    • Pull the riser main until the base of the T-handle is at a comfortable height to work on.

    Kommentar hinzufügen

    • Loosen the jam nut from the base of the T-handle.

    • Unscrew the T-handle from the top of the riser main.

    • Remove the T-handle, making sure to hold the remaining end of the riser main to prevent dropping it down the well.

    Kommentar hinzufügen

    • Continue to pull the riser main out of the well.

    Kommentar hinzufügen

    • Keep pulling until the first joint is exposed.

    • Lift the joint up to a comfortable working height.

    Kommentar hinzufügen

    • Use two wrenches to loosen the top section of riser main from the lower section.

    • Unscrew the top section of the riser main.

    • Make sure someone is holding the remaining section of the riser main.

    Kommentar hinzufügen

    • Remove the top section of the riser main.

    Kommentar hinzufügen

    • Lay the first section of riser main in a sanitary place to prevent contamination.

    • Repeat the previous procedure to remove the remaining sections of the riser main from the well.

    • Lay each new piece in the order it was removed to aid in reassembly.

    Kommentar hinzufügen

    • The last section of riser main will have the traveling valve screwed on to the end, and the foot valve hooked onto the traveling valve.

    • Be careful not to allow the foot valve to release from the hook by pulling slowly on the riser main.

    Kommentar hinzufügen

    • Lift and twist the foot valve to unhook it from the traveling valve.

    Kommentar hinzufügen

    • Once the riser main and valves have been removed from the well, place a rag over the top to prevent accidentally dropping anything down the well.

    Kommentar hinzufügen

Abschluss

To reassemble your device, follow these instructions in reverse order.

Sam Lionheart

Mitglied seit 18.10.2012

345.284 Reputation

535 Anleitungen geschrieben

Team

iFixit Mitglied von iFixit

Community

113 Mitglieder

7.300 Anleitungen geschrieben

Kommentar hinzufügen

Statistik anzeigen:

Letzte 24 Stunden: 0

Letzte 7 Tage: 0

Letzte 30 Tage: 3

Insgesamt: 216