Einleitung

In this guide we will be replacing the backup battery for the TI-92.

The first step to any repair operation is to remove the front cover. Grab the back of the calculator with one hand and the cover with the other. Pull the cover off from one of the sides for easy removal.
  • The first step to any repair operation is to remove the front cover.

  • Grab the back of the calculator with one hand and the cover with the other.

  • Pull the cover off from one of the sides for easy removal.

Kommentar hinzufügen

Orientate the calculator with the top facing towards you. Slide the locking tab,found on the top part of the calculator, to the unlock position.
  • Orientate the calculator with the top facing towards you.

  • Slide the locking tab,found on the top part of the calculator, to the unlock position.

Kommentar hinzufügen

"Locking Tab" To remove the back cover, slide the cover away from the locking tab towards the bottom of the calculator until the cover no longer slides.
  • "Locking Tab"

  • To remove the back cover, slide the cover away from the locking tab towards the bottom of the calculator until the cover no longer slides.

  • Then with the front of the calculator facing down, pull up on the back cover.

  • The calculator should now be orientated with the front facing down, as shown in picture 2.

Kommentar hinzufügen

Before removing the backup battery make sure your AA batteries are installed so that there is no loss of information.
  • Before removing the backup battery make sure your AA batteries are installed so that there is no loss of information.

  • Using a #00 Philip Screwdriver remove the 19mm screw located near the center of the back of the calculator on the panel with words "Test Access"

Kommentar hinzufügen

Remove the screw and lift the panel to access battery.
  • Remove the screw and lift the panel to access battery.

Kommentar hinzufügen

The backup battery can now be seen underneath a small metal cover held by a screw. Using the same screwdriver, unscrew the 4.6mm screw located under the panel and left of the backup battery.
  • The backup battery can now be seen underneath a small metal cover held by a screw.

  • Using the same screwdriver, unscrew the 4.6mm screw located under the panel and left of the backup battery.

Kommentar hinzufügen

Remove the metal cover keeping the backup battery in place. Remove the metal cover keeping the backup battery in place. Remove the metal cover keeping the backup battery in place.
  • Remove the metal cover keeping the backup battery in place.

Kommentar hinzufügen

Use an Ipod Opening Tool or a similar tool to pull up on the right side of the backup battery. The battery should pop out of position.
  • Use an Ipod Opening Tool or a similar tool to pull up on the right side of the backup battery.

  • The battery should pop out of position.

Kommentar hinzufügen

After the battery has been tilted out of its socket, simply remove it with your hands. After the battery has been tilted out of its socket, simply remove it with your hands.
  • After the battery has been tilted out of its socket, simply remove it with your hands.

Kommentar hinzufügen

Abschluss

To reassemble your device, follow these instructions in reverse order.

2 weitere Nutzer haben diese Anleitung absolviert.

Daniel Maldonado

Mitglied seit 14.04.2010

177 Reputation

9 Anleitungen geschrieben

Team

Cal Poly, Team 15-51, Garner Spring 2010 Mitglied von Cal Poly, Team 15-51, Garner Spring 2010

CPSU-GARNER-S10S15G51

5 Mitglieder

9 Anleitungen geschrieben

Kommentar hinzufügen

Statistik anzeigen:

Letzte 24 Stunden: 2

Letzte 7 Tage: 6

Letzte 30 Tage: 16

Insgesamt: 3,990