Zum Hauptinhalt wechseln

Diese Version enthält möglicherweise inkorrekte Änderungen. Wechsle zur letzten geprüften Version.

Was du brauchst

  1. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 1, Bild 1 von 3 : Schritt 1, Bild 2 von 3 : Schritt 1, Bild 3 von 3
    • Here is the Toshiba Satellite C655D-S5200

    • Open the laptop with the LCD facing forward. There are four rubber caps, one in each corner

    • Removing the plugs reveal the Phillips screws

  2. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 2, Bild 1 von 3 : Schritt 2, Bild 2 von 3 : Schritt 2, Bild 3 von 3
    • Remove all four screws, tow on top left and right corner

    • One on the bottom left corner

    • and the bottom right corner.

    • Here are the four M3x5mm screws

  3. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 3, Bild 1 von 3 : Schritt 3, Bild 2 von 3 : Schritt 3, Bild 3 von 3
    • Use a plastic opening tool, or similar to pop the bezel of the LCD assembly

    • Continue to slide the tool all the way across the top

    • Once the bezel has been released from the tabs, it can be further released be applying some gently manual pulling

  4. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 4, Bild 1 von 3 : Schritt 4, Bild 2 von 3 : Schritt 4, Bild 3 von 3
    • Continue to pull gently on the sides

    • and finally on the bottom.

    • With all the tabs released the bezel can now be removed.

  5. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 5, Bild 1 von 3 : Schritt 5, Bild 2 von 3 : Schritt 5, Bild 3 von 3
    • Here is the LCD assembly without the bezel

    • Remove the Phillips screw that connects the LCD frame to the back cover. This is the left one

    • Remove the right one as well

  6. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 6, Bild 1 von 3 : Schritt 6, Bild 2 von 3 : Schritt 6, Bild 3 von 3
    • The LCD can now be moved forward and away from the rear cover

    • There are three screws on either side that hold the panel to the frame. Remove those

    • Here are the three M2x4 screws

  7. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 7, Bild 1 von 3 : Schritt 7, Bild 2 von 3 : Schritt 7, Bild 3 von 3
    • Remove the three Phillips screws on the right side as well.

    • with the screws removed the panel can now be moved out of the LCD frame. The LCD is still connected by the display cable.

    • The display cable is secured to the connector with some clear adhesive. Remove this frist

  8. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 8, Bild 1 von 2 : Schritt 8, Bild 2 von 2
    • Remove the display cable carefully.

    • With the display cable disconnected, the LCD can now be removed and replaced.

Ziellinie

Ein:e weitere:r Nutzer:in hat diese Anleitung absolviert.

oldturkey03

Mitglied seit: 09/29/10

783.219 Reputation

119 Anleitungen geschrieben

Team

Global Fixers Mitglied von Global Fixers

Community

33 Mitglieder

549 Anleitungen geschrieben

0 Kommentare

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 2

Letzte 7 Tage: 8

Letzte 30 Tage: 11

Insgesamt: 1,515