Ersatzteile

Kein Ersatzteil erforderlich.

  1. With the battery away from you, slide the locking clips out.
    • With the battery away from you, slide the locking clips out.

      • The left clip stays, the right clip is spring loaded.

    • Slide the battery away from you.

    Kommentar hinzufügen

  2. Use a spudger to carefully pry up the keyboard screw cover.
    • Use a spudger to carefully pry up the keyboard screw cover.

    Kommentar hinzufügen

    • Remove the two screws securing the keyboard to the chassis.

    Kommentar hinzufügen

    • Carefully tilt the keyboard towards you and release the ribbon cables.

    • Use a spudger if needed to release the latch. The latch slides out.

    • The keyboard is now free and can be set aside.

    Kommentar hinzufügen

    • Remove the five black screws

    • Remove the one silver screw

    Kommentar hinzufügen

    • Flip the laptop over so the bottom is facing up.

    • Using a spudger, remove the seven rubber inserts.

      • The feet only go in one location on the bottom of the laptop, so save yourself some time and track where they go.

    Kommentar hinzufügen

    • Remove the six silver screws.

    • Remove the one black screw.

    Kommentar hinzufügen

  3. Frohes Fest, frohes Tüfteln
    Pack's ein, pack's aus, pack's an: Erhalte 12 € Rabatt auf deinen Einkauf ab 50 € mit dem Code FIXMAS12
    Frohes Fest, frohes Tüfteln
    Pack's ein, pack's aus, pack's an: Erhalte 12 € Rabatt auf deinen Einkauf ab 50 € mit dem Code FIXMAS12
    • Stand the laptop up on end.

    • Remove the two rubber inserts from the back of the laptop. One insert is on each side of the laptop.

    Kommentar hinzufügen

    • Remove the two screews.

    Kommentar hinzufügen

    • Carefully work a spudger in the crack at the back of the laptop and separate the small rubberized section from the bottom of the laptop.

    Kommentar hinzufügen

    • Remove the four screws.

    • Disconnect the black wireless antenna lead.

    Two outer are larger in diameter…

    mitchgwin - Antwort

    • The bottom of the laptop is now ready to lift off.

    • Carefully work a spudger around the seam of the laptop separating the bottom from the rest of the laptop.

      • There is a data connection at the front of the laptop that needs to be disconnected.

      • Use a spuder to carefully disconnect the wire from the motherboard. Once this is free the bottom will come off.

    Another data connection at rear near battery…

    mitchgwin - Antwort

    • Locate the hard drive.

    • Remove the three screws.

    • Slide the hard drive out away from the motherboard connector.

      • Once the hard drive is disconnected it lifts out.

    Kommentar hinzufügen

    • Locate the wireless card.

    • Remove the white antenna lead.

    • Remove the single screw.

    • Lift the card up from the edge with the screw, and pull out.

    Kommentar hinzufügen

    • Locate optical drive

    • Remove the three screws securing the optical drive.

    • Slide the optical drive away from the motherboard, and carefully lift up.

    Kommentar hinzufügen

    • Carefully flip the laptop rightside up and open the lid.

    • Disconnect the cables from the motherboard.

    Kommentar hinzufügen

    • Close the laptop lid, and flip back over so you see the motherboard.

    • Disconnect all cables from the motherboard.

    • This wire holder is stuck on with a little glue and should lift right off.

    Kommentar hinzufügen

    • Remove the heatsink screws. And lift up the heatsink.

      • The screws remain attached to the heatsink.

    • Remove the three screws holding the motherboard to the chasis.

    Kommentar hinzufügen

    • Lift up on ribbon cable latch.

    • Gently disconnect ribbon cable from motherboard.

    • The motherboard should lift out.

    Kommentar hinzufügen

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tyler

Mitglied seit 19.06.2012

4.189 Reputation

16 Anleitungen geschrieben

Team

TechForce Mitglied von TechForce

Business

2 Mitglieder

18 Anleitungen geschrieben

This guide could really use an explanation of how to disconnect the different types of cables from the motherboard. In particular, the descriptions for steps 16 and 17 are completely inadequate to me.

gitm - Antwort

Also, to replace the motherboard you must remove the CPU and RAM from the motherboard, so they can be connected to the new one. This guide does not cover that.

gitm -

Anther important omission is the data connection to the card reader, which needs to be disconnected in Step 11 (this is one of two connections between the motherboard and the bottom of the case).

gitm -

Kommentar hinzufügen

Statistik anzeigen:

Letzte 24 Stunden: 0

Letzte 7 Tage: 2

Letzte 30 Tage: 7

Insgesamt: 428