Einleitung
This guide will show how the motherboard of the UE Boom 2 Bluetooth speaker is removed. This is an extensive and intrusive process which removes all components of the speaker.
Was du brauchst
-
-
First, remove the D-ring located on the bottom of the UE Boom 2, the opposite end of the power button.
-
Remove by twisting in a counter-clockwise motion.
-
-
-
Remove the rubber stripping using a metal spudger.
-
Work around the edge of the rubber stripping slowly prying up the edge.
-
-
-
On the bottom, unscrew the four 15mm Phillips Head #2 screws, using a Phillips head #2 screwdriver.
-
Pry up at the location marked, and remove the plastic end cap
-
-
-
Now on the top, unscrew the four 15 mm Phillips Head #2 screws, using a Phillips Head #2 screwdriver.
-
Using the metal spudger, pry up the plastic cap at the point marked and remove the cap.
-
-
-
Carefully un-loop the cable with a plastic opening tool or spudger and unplug it from motherboard.
-
Pull out the battery, and handle with care.
-
-
-
Using the metal spudger, pry up the plastic tab on the inside.
-
Pry up around the entire inside circumference.
-
Repeat on the other end.
-
-
-
-
Using the metal spudger tool, pry up the inside edge of the mesh lining.
-
Working down the strip on both sides. Careful as to not rip the mesh.
-
-
-
Unscrew the two 5 mm Phillips head #1 screws, using a Phillips Head #1 screwdriver.
-
Using the metal spudger, pry open the edge of the cover.
-
-
-
Using the metal spudger, pry the plastic casing up.
-
Repeat on the other side of the speaker.
-
-
-
Using the metal spudger, specifically the pointy end, find the gap between the speaker and billow (the larger rectangular speaker-like-object next to the speaker).
-
Pry the metal wire up and out at exactly this gap, then slide down wire towards one end to pop it out completely.
-
Once one end is out, use your fingers to gently pull off completely so as not to bend the wire too aggressively.
-
-
-
Using the metal spudger, work it under the billow.
-
Work the billow up around all edges, and pull out of casing.
-
-
-
With the billow removed, pry up the pink rubber seal using a metal spudger.
-
Remove using fingers.
-
-
-
Using the metal spudger, work it under the edge of the speaker.
-
Work around the speaker on all sides.
-
-
-
Now, both the billow and speaker have been removed from one side of the Boom 2, repeat steps 13-18 for the other side.
-
-
-
Using angled tweezers, pull up the black sheath on tan connector port.
-
Gently pull the white ribbon cable out from connector.
-
-
-
With the ribbon cable disconnected from the motherboard, remove the bluetooth antennae.
-
-
-
Confirm that all cables from speakers, Bluetooth antenna, and battery have been disconnected from the motherboard.
-
Grab the single piece of green motherboard that runs perpendicular to the motherboard, and pull out of casing.
-
To reassemble your device, follow these instructions in reverse order.
To reassemble your device, follow these instructions in reverse order.
Rückgängig: Ich habe diese Anleitung nicht absolviert.
4 weitere Nutzer:innen haben diese Anleitung absolviert.
4 Kommentare
Buenas tardes
Disculpe las molestias. En mi equipo ue boom 2 no sale audio, ya desarme siguiendo los paso y medi Ω de sus parlantes, y estan en su valor me puede ayudar con este problema.
O se puede cambiar toda la tarjeta madre.
Le agradezco de antemano .
Estare atento a cualquier respuesta.
Where can I get a new motherboard or get my current one repaired?
My Boom 2 won’t respond. Doesn’t make any sounds when pressing bottoms, and Bluetooth doesn’t work. If it’s connected to power and using an aux cord it works. But unless connected to power the speaker won’t turn on or work at all. I checked the condition of the battery and it’s voltage was perfect. Could this problem be to do with the mother board and would replacing it fix these problems. Any advice you have would be brilliant. Thanks