Zum Hauptinhalt wechseln

Einleitung

This guide entails and explains the simple steps to replace the non-functioning keyboard on the Uniden Dect 6.0 home phone.

Ersatzteile

Keine Ersatzteile angegeben.

  1. Locate the battery compartment on the back of the Uniden home phone.
    • Locate the battery compartment on the back of the Uniden home phone.

    • Place your finger on the groove, and pull directly back on the cover to access to the battery.

    the hand set does not work nither one will charge I just bought it from Walmart in sant cloud florida I have the uniden 6.0 answering mic plus the 2 hand sets 1 for the base and 1 for the ex phone what do I do because I had it on charge for 2 days now.i m disabled and need I phone to work thank you for any help u can give me or please send me 2 batterys 1 for each phone and I will send the 2 I just got with my new phone hope that works after I replace the batterys ty u can send to 1311 w rosewood ave sant cloud florida 34771 thank you

    star - Antwort

    It is very difficult to open the battery compartment.

    Thomas Alessi - Antwort

    Does it slide down or open out from where the finger groove is?

    I can’t get it off.

    K scott - Antwort

    I had the same problem removing the back. I placed a knife in the center and was finally able to get it off. I think the red & black wire on the battery causes the problem.

    Tanya Brown - Antwort

    I tried knife, but I can't get battery cover off of one of the Uniden phones. I have new batteries but can't get the blasted cover off.

    Carolyn B - Antwort

  2. Remove the white battery pack from the battery compartment.
    • Remove the white battery pack from the battery compartment.

  3. Remove the red-and-black-wired port from the plug directly under the battery compartment.
    • Remove the red-and-black-wired port from the plug directly under the battery compartment.

  4. Using a Phillips #1 screwdriver, remove the two .9 mm screws on the back of the device on each side of the battery pack. Using a Phillips #1 screwdriver, remove the two .9 mm screws on the back of the device on each side of the battery pack.
    • Using a Phillips #1 screwdriver, remove the two .9 mm screws on the back of the device on each side of the battery pack.

  5. Using your fingers, gently lift and separate the front of the housing from the back housing.
    • Using your fingers, gently lift and separate the front of the housing from the back housing.

    • Potential for device damage: While separating the back housing from the front, be sure to open from the sides as pictured.

  6. Gently remove the loose keyboard from the lined gel casing located under the front housing of the front of the phone.
    • Gently remove the loose keyboard from the lined gel casing located under the front housing of the front of the phone.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Ein weiterer Nutzer hat diese Anleitung absolviert.

Megan Lawrence

Mitglied seit: 14.01.2015

534 Reputation

5 Anleitungen geschrieben

Team

USF Sarasota-Manatee, Team 1-3, Stewart Winter 2015 Mitglied von USF Sarasota-Manatee, Team 1-3, Stewart Winter 2015

USFSM-STEWART-W15S1G3

4 Mitglieder

9 Anleitungen geschrieben

Ein Kommentar

Great to have this guide! I’d add that (at least on my aging handset). Prying it open can feel a bit sketchy cause it may resist a bit, so I used the metal spudger to go around the edge lifting the tabs. But the plastic on these is pretty great and will not break even puting some force on it.

Also be mindful of the speaker on the back which is connected to the front case.

Ivan Viales - Antwort

Kommentar hinzufügen

Seitenaufrufe:

Letzten 24 Stunden: 0

Letzten 7 Tage: 5

Letzten 30 Tage: 19

Insgesamt: 2,888