Zum Hauptinhalt wechseln

Repariere deine Sachen

Recht auf Reparatur

Werkzeug & Ersatzteile

Einleitung

What you can expect from this guide is a step by step process on how to remove the battery on a Verizon Ellipsis Jetpack MHS800L.

  1. Remove the SIM card, that is located on top of the Jetpack. Remove the SIM card, that is located on top of the Jetpack. Remove the SIM card, that is located on top of the Jetpack.
    • Remove the SIM card, that is located on top of the Jetpack.

  2. With the device on its back and the label facing you, remove the rubber screw cover on the top left corner of the device. Under the rubber circle, remove the 1.25 mm screw using a Philips #00 screwdriver. You may need to peel back a piece of double sided tape covering the screw hole.
    • With the device on its back and the label facing you, remove the rubber screw cover on the top left corner of the device.

    • Under the rubber circle, remove the 1.25 mm screw using a Philips #00 screwdriver.

    • You may need to peel back a piece of double sided tape covering the screw hole.

  3. Remove three 1.25 mm screws.
    • Remove three 1.25 mm screws.

    Are steps 3 and 4 reversed? Where are the 3 screws?

    imsonnyburnett - Antwort

    Th3 first left corner has a screw but under the cover on the others is just a black circle

    Audrie nelson - Antwort

  4. Nintendo Switch Kits

    Eine schnelle Lösung, um wieder ins Spiel zu kommen

    Switch Kits kaufen

    Nintendo Switch Kits

    Eine schnelle Lösung, um wieder ins Spiel zu kommen

    Switch Kits kaufen
  5. Use a plastic opening tool at the seams and pry open the case.
    • Use a plastic opening tool at the seams and pry open the case.

  6. Once the cover is off, this is what your device will look like.
    • Once the cover is off, this is what your device will look like.

  7. Once you have the case off of your device gently pull your battery away from the device. Do not attempt to completely remove the battery, as it is still attached to the motherboard by wires.
    • Once you have the case off of your device gently pull your battery away from the device.

    • Do not attempt to completely remove the battery, as it is still attached to the motherboard by wires.

  8. With a pair of ESD Tweezers remove the yellow tape covering the battery wires. With a pair of ESD Tweezers remove the yellow tape covering the battery wires.
    • With a pair of ESD Tweezers remove the yellow tape covering the battery wires.

  9. After removing the tape you may use the ESD Tweezers to remove the wiring harness from the circuit board.
    • After removing the tape you may use the ESD Tweezers to remove the wiring harness from the circuit board.

    • Do not squeeze the wires to hard you may damage them and cause a short.

    oh, good

    ‘only squeeze hard enough’

    it’s a good thing I have a bucket of these upon which to experiment? oh, wait, I don’t.

    baily jacoby - Antwort

    I just replaced the battery in my JetPack. The connector does NOT slide out towards the wires; instead, use the tweezers to gently grasp all of the wires, and then lift them straight up and away from the unit.

    Reattach the new battery by locating the connector over the receptacle, and push the connector straight down into place. Replace the yellow tape, and reassemble the unit. This worked for me! I hope it helps others.

    Mike A. - 04 April, 2019

    Michael Aube - Antwort

  10. You may now replace  the battery in your Verizon Ellipsis Jetpack MHS800L.
    • You may now replace the battery in your Verizon Ellipsis Jetpack MHS800L.

    For a mere $27 get a nearly matching battery. Amazon ASIN B01E0SEXS2

    a good condition jetpack on ebay is $17.

    baily jacoby - Antwort

Abschluss

To reassemble your device, follow these instructions in reverse order.

6 weitere Nutzer haben diese Anleitung absolviert.

Richard J Porras

Mitglied seit: 23.01.2016

504 Reputation

3 Anleitungen geschrieben

Team

IUPUI, Team 3-3, Baechle Spring 2016 Mitglied von IUPUI, Team 3-3, Baechle Spring 2016

IUPUI-BAECHLE-S16S3G3

4 Mitglieder

3 Anleitungen geschrieben

I'd like to let you know that after step 9, it is possible to unwrap the battery and break loose the circuit board on the battery. At which point you can reinstall the circuit board in the router with no battery attached. This makes the Jetpack plug-in only which is all I need it for anyways. It was a great and free fix for my swollen battery.

Thanks for the article!

Jeff Lovett - Antwort

Opps, I think that steps 3 & 4 have been reversed. You can't get to the "3 additional screws" until you're looking at the red cover which is below the black cover that needs to be pried off first.

Otherwise, the process seems to be going well.

bevrievley - Antwort

It’s unclear. Once you unscrew that first screw, you have to remove the TOP black portion (the picture looks like you’re removing the bottom). Once you remove that top portion, the red plastic is exposed, revealing the three other screws.

imsonnyburnett -

And -- continuing with step 5, there are some plastic "snap" locks between the red and black covers -- 5 by my count, 2 along each of the long edges, 1 along the charging port edge. Always good to pry carefully.

Once apart, battery is on bottom and can be easily removed/replaced as per steps 7 & 8.

bevrievley - Antwort

now how do we FORCE a factory data reset without the admin password?

baily jacoby - Antwort

Kommentar hinzufügen

Statistik anzeigen:

Letzten 24 Stunden: 3

Letzten 7 Tage: 17

Letzten 30 Tage: 59

Insgesamt: 6,307