Zum Hauptinhalt wechseln

Wii U GamePad äußeres Gehäuse tauschen

Was du brauchst

  1. Wii U GamePad äußeres Gehäuse tauschen, Akku: Schritt 1, Bild 1 von 2 Wii U GamePad äußeres Gehäuse tauschen, Akku: Schritt 1, Bild 2 von 2
    • Lege das GamePad mit der Unterseite nach oben und drehe die beiden Kreuzschlitzschrauben #00 vom Akkufach heraus.

    • Hebe den Akkufachdeckel hoch und entferne ihn.

  2. Wii U GamePad äußeres Gehäuse tauschen: Schritt 2, Bild 1 von 3 Wii U GamePad äußeres Gehäuse tauschen: Schritt 2, Bild 2 von 3 Wii U GamePad äußeres Gehäuse tauschen: Schritt 2, Bild 3 von 3
    • Lege deinen Finger auf den Akkustecker und schiebe ihn zur Unterkante des Geräts hin, so dass er sich ablöst.

    • Ziehe den Akku an der Unterkante nach oben und löse ihn heraus.

  3. Wii U GamePad äußeres Gehäuse tauschen, Äußeres Gehäuse: Schritt 3, Bild 1 von 3 Wii U GamePad äußeres Gehäuse tauschen, Äußeres Gehäuse: Schritt 3, Bild 2 von 3 Wii U GamePad äußeres Gehäuse tauschen, Äußeres Gehäuse: Schritt 3, Bild 3 von 3
    • Entferne die zehn 8,9 mm Tri-Wing Y1 Schrauben unter den quadratischen Aufklebern.

    • Hebe die Rückabdeckung an.

    • Die Rückabdeckung ist immer noch über ein Kabel mit der Hauptplatine verbunden.

    how do i replace the whole front and back casing?

    enbodylin - Antwort

    bruh the ifix it screwdriver dont reach down the whole way

    Michael - Antwort

    I feel like it’s important to mention how deep some of these holes are. Your screwdriver might not reach. Mine sure didn’t.

    greatshadowdude - Antwort

    I had to shove some tissue into the screwdriver bit holder to get it to reach

    Andrew Walker - Antwort

  4. Wii U GamePad äußeres Gehäuse tauschen: Schritt 4, Bild 1 von 2 Wii U GamePad äußeres Gehäuse tauschen: Schritt 4, Bild 2 von 2
    • Löse den Stecker, der die Rückabdeckung mit der Hauptplatine verbindet.

    • Entferne die Rückabdeckung.

    You don't have to remove just be careful

    Heather Sheppard - Antwort

    I tried to remove like at least 6 times but I wasn’t able to. Using tweezer, my nails, long nose pliers. There could be a lock but I gave up since I’m afraid if I put more force I might accidentally pull the wires. I’m able to remove the left and right analog stick with the back plate plugged, as mentioned, just be careful.

    Royce Remulla - Antwort

    I was stuck on this step for a while - note that you’re only removing the little white plastic bit. The beige or yellowish plastic bit is attached to the board. I needed to use pliers to carefully grab just the white plastic bit and wiggle it side to side.

    Nova H - Antwort

Abschluss

Um dein Gerät wieder zusammenzubauen, folge den Schritten in umgekehrter Reihenfolge.

11 weitere Nutzer:innen haben diese Anleitung absolviert.

Besonderer Dank geht an diese Übersetzer:innen:

en de

100%

Diese Übersetzer:innen helfen uns, die Welt zu reparieren! Wie kann ich mithelfen?
Hier starten ›

Kim Arre

Mitglied seit: 01/11/13

4.888 Reputation

8 Anleitungen geschrieben

Team

Cal Poly, Team 17-20, Forte Winter 2013 Mitglied von Cal Poly, Team 17-20, Forte Winter 2013

CPSU-FORTE-W13S17G20

5 Mitglieder

38 Anleitungen geschrieben

2 Kommentare

This is either incomplete or mistitled - it is a currently a back plate replacement guide.

At the conclusion of this how-to/walkthrough, most of the GamePad's hardware is still attached to the front plate, one half of the outer case.

Elijah - Antwort

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 7

Letzte 7 Tage: 39

Letzte 30 Tage: 123

Insgesamt: 14,513