Zum Hauptinhalt wechseln

Diese Version enthält möglicherweise inkorrekte Änderungen. Wechsle zur letzten geprüften Version.

XBOX 360 Hauptplatine ersetzen

Was du brauchst

  1. XBOX 360 Hauptplatine ersetzen, Festplatte: Schritt 1, Bild 1 von 3 XBOX 360 Hauptplatine ersetzen, Festplatte: Schritt 1, Bild 2 von 3 XBOX 360 Hauptplatine ersetzen, Festplatte: Schritt 1, Bild 3 von 3
    • Lege die Xbox 360 S so hin, das sie mit der Unterseite zu dir zeigt.

    • Schiebe die Einkerbung der Festplattenabdeckung nach links.

    • Ziehe die Festplattenabdeckung von der Konsole weg.

  2. XBOX 360 Hauptplatine ersetzen: Schritt 2, Bild 1 von 3 XBOX 360 Hauptplatine ersetzen: Schritt 2, Bild 2 von 3 XBOX 360 Hauptplatine ersetzen: Schritt 2, Bild 3 von 3
    • An der Festplatte ist eine Lasche aus Gewebe angebracht, auf der die Kapazität der Festplatte (z.B. "250 GB") aufgedruckt ist. Fasse die Lasche fest an.

    • Ziehe die Festplatte gerade aus der Konsole heraus.

    • Die Stofflasche ist an einer Verriegelung weiter im Festplattengehäuse befestigt. Du musst ein wenig Kraft aufwenden, um die Festplatte herauszuziehen.

  3. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    XBOX 360 Hauptplatine ersetzen: Schritt 3, Bild 1 von 1
    • In the following steps, you will remove the bottom vent.

    • It is attached to the bottom panel by the seven clips shown.

  4. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    XBOX 360 Hauptplatine ersetzen: Schritt 4, Bild 1 von 2 XBOX 360 Hauptplatine ersetzen: Schritt 4, Bild 2 von 2
    • Orient the Xbox 360 S so that the hard drive port is facing up and the faceplate is facing to the left.

    • Insert a metal spudger between the black bottom vent and the silver rim of the bottom bezel, in the rear right corner of the vent.

    • Rotate the spudger away from the console, prying the vent up from the bottom bezel.

    • Be sure to rotate the spudger far enough so that the clips on the vent are lifted past the silver rim of the bottom bezel.

  5. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    XBOX 360 Hauptplatine ersetzen: Schritt 5, Bild 1 von 3 XBOX 360 Hauptplatine ersetzen: Schritt 5, Bild 2 von 3 XBOX 360 Hauptplatine ersetzen: Schritt 5, Bild 3 von 3
    • In the same manner as described above, pry the two remaining clips on the bottom right edge.

    • All of the clips along both the right and front edge should now be free. If other clips have come undone as well, that is fine.

  6. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    XBOX 360 Hauptplatine ersetzen: Schritt 6, Bild 1 von 2 XBOX 360 Hauptplatine ersetzen: Schritt 6, Bild 2 von 2
    • Remove the bottom vent by lifting it away from the bottom bezel.

  7. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    XBOX 360 Hauptplatine ersetzen: Schritt 7, Bild 1 von 2 XBOX 360 Hauptplatine ersetzen: Schritt 7, Bild 2 von 2
    • In the following steps, you will remove the bottom bezel, which is attached to the rest of the console by the six clips shown.

    • The clips shown in red can be detached by inserting a metal spudger underneath the bottom edge of the clip. Once underneath the bottom edge, simply prying away from the console will free the clip.

  8. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    XBOX 360 Hauptplatine ersetzen: Schritt 8, Bild 1 von 2 XBOX 360 Hauptplatine ersetzen: Schritt 8, Bild 2 von 2
    • Insert a metal spudger through the slit near the rear left corner of the bottom bezel.

    • Rotate the spudger away from the device while lifting the rear bezel up with the other hand.

    • You may hear a "pop" signifying the clip has cleared its catch.

  9. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    XBOX 360 Hauptplatine ersetzen: Schritt 9, Bild 1 von 2 XBOX 360 Hauptplatine ersetzen: Schritt 9, Bild 2 von 2
    • Insert a metal spudger through the left middle slit of the bottom bezel, and between the bottom edge of the clip and the left case.

    • Simultaneously pull the bottom bezel up and rotate the spudger away from the console to free the clip.

    • In a similar fashion, free the clip at the front of the bottom bezel's left edge.

    • The entire left side of the bottom bezel should now be free.

  10. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    XBOX 360 Hauptplatine ersetzen: Schritt 10, Bild 1 von 2 XBOX 360 Hauptplatine ersetzen: Schritt 10, Bild 2 von 2
    • Turn the console around so that the faceplate is facing to the right and the right case is facing toward you.

    • Insert the spudger into the rear-most slit on the right edge of the bottom bezel, and wedge it behind the clip by pushing the spudger down while pushing the tip of the spudger against the right case.

    • Simultaneously release the clip and pull the bottom bezel up.

    • This clip is especially hard to remove. Some force will be required to insert the spudger correctly.

  11. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    XBOX 360 Hauptplatine ersetzen: Schritt 11, Bild 1 von 1
    • This clip does not have a slit in the bezel to guide you. You can locate the clip by looking under the bezel near the hard drive slot.

    • Insert a spudger between the silver rim and bottom bezel directly above the clip shown.

    • Release the clip while pulling up on the bottom bezel.

  12. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    XBOX 360 Hauptplatine ersetzen: Schritt 12, Bild 1 von 2 XBOX 360 Hauptplatine ersetzen: Schritt 12, Bild 2 von 2
    • This clip is smaller than the others and should not be removed from above like the others.

    • Lift the left edge of the bottom bezel up enough to gain clearance.

    • Insert a metal spudger behind the left edge of the last clip, and push the clip away from the right case.

  13. XBOX 360 Hauptplatine ersetzen: Schritt 13, Bild 1 von 1
    • In den folgenden Schritten wirst du die Abdeckung an der Oberseite mit den Lüftungsschlitzen entfernen, welche mit 13 Clips an den gezeigten Stellen festgehalten wird.

    • Wenn du die Abdeckung mit den Lüftungsschlitzen entfernst, musst du vorsichtig sein, dass du die Plastik-Clips nicht beschädigst.

  14. XBOX 360 Hauptplatine ersetzen: Schritt 14, Bild 1 von 2 XBOX 360 Hauptplatine ersetzen: Schritt 14, Bild 2 von 2
    • Richte die Konsole so aus, dass die Worte "XBOX 360" auf der Seite nach oben zeigen und die Frontplatte nach links zeigt.

    • Führe einen Metall-Spudger zwischen den Lüftungsschlitzen auf der Oberseite und der oberen Abdeckung bei der Rückseite ein.

    • Drehe den Spudger von der Konsole weg, sodass du die Kante der Abdeckung mit den Lüftungsschlitzen nach oben hebelst, bis die zwei Clips sich lösen.

    • Drehe den Spudger weit genug, sodass die Clips den silbernen Rand der oberen Einfassung freigeben.

  15. XBOX 360 Hauptplatine ersetzen: Schritt 15, Bild 1 von 3 XBOX 360 Hauptplatine ersetzen: Schritt 15, Bild 2 von 3 XBOX 360 Hauptplatine ersetzen: Schritt 15, Bild 3 von 3
    • Führe einen Metall-Spudger zwischen den Lüftungsschlitzen und der oberen Abdeckung entlang der linken Seite ein.

    • Auf die gleiche Art und Weise wie oben, heble die linke Seite der Lüftungsschlitze von der oberen Abdeckung ab.

    • Heble weiter der linken Seite entlang, bis alle Clips auf dieser Seite gelöst sind.

  16. XBOX 360 Hauptplatine ersetzen: Schritt 16, Bild 1 von 2 XBOX 360 Hauptplatine ersetzen: Schritt 16, Bild 2 von 2
    • Hebe die Abdeckung mit den Lüftungsschlitzen an der befreiten linken Seite an, um die Clips auf der anderen Seite zu lösen.

    • Entferne die Abdeckung mit den Lüftungsschlitzen.

  17. XBOX 360 Hauptplatine ersetzen: Schritt 17, Bild 1 von 2 XBOX 360 Hauptplatine ersetzen: Schritt 17, Bild 2 von 2
    • In den folgenden Schritten wirst du die sechs rot markierten Clips lösen.

    • Jeder Clip kann gelöst werden, indem du einen Spudger unter den unteren Rand des Clips einführst. Sobald du unter diesem Rand bist, wird einfaches Hebeln von der Konsole weg den Clip lösen.

  18. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    XBOX 360 Hauptplatine ersetzen: Schritt 18, Bild 1 von 2 XBOX 360 Hauptplatine ersetzen: Schritt 18, Bild 2 von 2
    • Orient the console so that the left case is facing toward you and the faceplate is facing toward the right.

    • Insert a metal spudger through the front-most slit on the left edge of the top bezel and between the bottom edge of the clip and the left case, as described above.

    • Simultaneously rotate the spudger away from the console and pull up on the top bezel to free the clip.

    • You will hear a "pop" signifying that the clip cleared its catch.

  19. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    XBOX 360 Hauptplatine ersetzen: Schritt 19, Bild 1 von 2 XBOX 360 Hauptplatine ersetzen: Schritt 19, Bild 2 von 2
    • Using the same method described above, free the two remaining clips along the left edge of the top bezel.

  20. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    XBOX 360 Hauptplatine ersetzen: Schritt 20, Bild 1 von 1
    • Grab the entire top panel with your hands, lift up the entire left edge high enough to rest the separated clips on top of the left case.

    • You may have to go back with a spudger and undo any clips that have re-attached.

    • The top panel will not come free of the console yet.

  21. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    XBOX 360 Hauptplatine ersetzen: Schritt 21, Bild 1 von 2 XBOX 360 Hauptplatine ersetzen: Schritt 21, Bild 2 von 2
    • Rotate the console so that the rear of the Xbox 360 S is facing to the right, and the right case is facing you.

    • Insert a metal spudger through the rear-most slit on the right edge of the top bezel and between the bottom edge of the clip and the right case.

    • While lifting up on the top bezel with your fingers, rotate the spudger away from the console to free the clip.

  22. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    XBOX 360 Hauptplatine ersetzen: Schritt 22, Bild 1 von 2 XBOX 360 Hauptplatine ersetzen: Schritt 22, Bild 2 von 2
    • In the same manner as described in the previous steps, release the middle and front clips along the right edge of the top panel.

  23. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    XBOX 360 Hauptplatine ersetzen: Schritt 23, Bild 1 von 1
    • Lift the top panel off the device.

    • You may have to go back with a spudger and undo any clips that have re-attached to the console.

  24. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    XBOX 360 Hauptplatine ersetzen: Schritt 24, Bild 1 von 1
    • Opening your Xbox 360 any further will require breaking or removing the warranty sticker on the outer case. Your Microsoft warranty for any components not directly attached to the logic board will likely be voided by removing this seal.

  25. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    XBOX 360 Hauptplatine ersetzen: Schritt 25, Bild 1 von 2 XBOX 360 Hauptplatine ersetzen: Schritt 25, Bild 2 von 2
    • Orient the console right-side up, with the faceplate facing toward you.

    • Locate the two clips connecting the right and left case along the top edge of the console, behind the Wi-Fi card.

    • While pushing the left and right case away from each other with one hand, pry the clips away from the case with a metal spudger.

  26. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    XBOX 360 Hauptplatine ersetzen: Schritt 26, Bild 1 von 2 XBOX 360 Hauptplatine ersetzen: Schritt 26, Bild 2 von 2
    • Continue to hold the two cases apart to prevent the clips reattaching.

    • Insert a spudger between the right and left cases to hold them separate while you work elsewhere.

  27. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    XBOX 360 Hauptplatine ersetzen: Schritt 27, Bild 1 von 2 XBOX 360 Hauptplatine ersetzen: Schritt 27, Bild 2 von 2
    • Flip the Xbox over so the faceplate is facing left, and the left case is facing toward you.

    • While pushing the left and right cases apart with one hand, free one clip located beside the hard drive slot.

  28. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    XBOX 360 Hauptplatine ersetzen: Schritt 28, Bild 1 von 2 XBOX 360 Hauptplatine ersetzen: Schritt 28, Bild 2 von 2
    • Continue to hold the cases apart to prevent the clips from reattaching.

    • Place another spudger between the left and right cases directly below the clip.

  29. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    XBOX 360 Hauptplatine ersetzen: Schritt 29, Bild 1 von 3 XBOX 360 Hauptplatine ersetzen: Schritt 29, Bild 2 von 3 XBOX 360 Hauptplatine ersetzen: Schritt 29, Bild 3 von 3
    • Insert the flat edge of a metal spudger between the left and right cases where the warranty sticker used to be.

    • Pry the left case upwards to form a gap between the two cases, and slide the spudger in toward the left case.

    • Rotate the spudger upward to release the last clip.

    • The spudgers holding the top and bottom clips apart may be removed.

  30. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    XBOX 360 Hauptplatine ersetzen: Schritt 30, Bild 1 von 2 XBOX 360 Hauptplatine ersetzen: Schritt 30, Bild 2 von 2
    • Release one clip in the front left corner of the top edge securing the left case to the faceplate.

  31. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    XBOX 360 Hauptplatine ersetzen: Schritt 31, Bild 1 von 2 XBOX 360 Hauptplatine ersetzen: Schritt 31, Bild 2 von 2
    • Flip the console over so the bottom is facing upward.

    • Release one clip in the front left corner of the bottom edge securing the left case to the faceplate.

    • Rotate the left case away from the device to release the last two inner clips.

    • Remove the left case.

  32. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    XBOX 360 Hauptplatine ersetzen: Schritt 32, Bild 1 von 2 XBOX 360 Hauptplatine ersetzen: Schritt 32, Bild 2 von 2
    • Orient the console right-side-up, with the faceplate facing forward.

    • Release the clip near the front right corner of the top edge securing the right case to the faceplate.

  33. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    XBOX 360 Hauptplatine ersetzen: Schritt 33, Bild 1 von 1
    • Turn the console over, so that the bottom is facing upward, and the faceplate is facing forward.

    • Release the clip in the bottom right corner of the top edge securing the right case to the front case.

  34. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    XBOX 360 Hauptplatine ersetzen: Schritt 34, Bild 1 von 2 XBOX 360 Hauptplatine ersetzen: Schritt 34, Bild 2 von 2
    • Lift the left edge of the faceplate upward to release the last two clips securing the faceplate to the right case.

    • Detach the faceplate from the rest of the device.

    • The faceplate is still attached to the console by a thin ribbon cable. Do not attempt to completely remove the faceplate yet.

  35. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    XBOX 360 Hauptplatine ersetzen: Schritt 35, Bild 1 von 3 XBOX 360 Hauptplatine ersetzen: Schritt 35, Bild 2 von 3 XBOX 360 Hauptplatine ersetzen: Schritt 35, Bild 3 von 3
    • Using a spudger or fingernail, lift the clear blue tab away from the connector.

    • Slide the locking tab on the power switch board cable connector toward the top of the console.

    • The locking tab will only move about 2 mm.

    • Pull the power switch cable straight out of the connector.

    • The faceplate is now free of the rest of the console.

  36. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    XBOX 360 Hauptplatine ersetzen: Schritt 36, Bild 1 von 1
    • Remove the two 5.6 mm T8 Torx screws securing the RF module to the metal case.

  37. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    XBOX 360 Hauptplatine ersetzen: Schritt 37, Bild 1 von 2 XBOX 360 Hauptplatine ersetzen: Schritt 37, Bild 2 von 2
    • The RF module is still connected to the Xbox by a large USB-type connector.

    • Pull the board directly away from the Xbox to remove it.

  38. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    XBOX 360 Hauptplatine ersetzen: Schritt 38, Bild 1 von 3 XBOX 360 Hauptplatine ersetzen: Schritt 38, Bild 2 von 3 XBOX 360 Hauptplatine ersetzen: Schritt 38, Bild 3 von 3
    • Remove the single T10 Torx screw holding in the wireless card.

    • Pull the Wi-Fi Board out of the console.

  39. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    XBOX 360 Hauptplatine ersetzen: Schritt 39, Bild 1 von 1
    • This is the terminal point if you ever want to send your Xbox back to Microsoft for repair.

    • Remove the large white warranty sticker from the metal frame to expose a screw.

  40. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    XBOX 360 Hauptplatine ersetzen: Schritt 40, Bild 1 von 1
    • Remove the five 55.5 mm T10 Torx screws securing the right case to the metal frame.

  41. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    XBOX 360 Hauptplatine ersetzen: Schritt 41, Bild 1 von 1
    • Turn the Xbox over so the right case is facing up.

    • Lift the right case off by its metal framework.

  42. XBOX 360 Hauptplatine ersetzen: Schritt 42, Bild 1 von 2 XBOX 360 Hauptplatine ersetzen: Schritt 42, Bild 2 von 2
    • Entferne das Datenkabel des optischen Laufwerks von der Rückseite des Laufwerks.

    • Entferne das Stromkabel von der Rückseite des Laufwerks.

  43. XBOX 360 Hauptplatine ersetzen: Schritt 43, Bild 1 von 1
    • Hebe das optische Laufwerk aus der Xbox heraus.

  44. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    XBOX 360 Hauptplatine ersetzen: Schritt 44, Bild 1 von 1
    • Turn the console over so that the metal case is facing up.

    • Remove the single 11.3 mm gold T10 Torx screw from the hole marked "G."

  45. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    XBOX 360 Hauptplatine ersetzen: Schritt 45, Bild 1 von 2 XBOX 360 Hauptplatine ersetzen: Schritt 45, Bild 2 von 2
    • Lift the fan duct off the fan.

    • There is a locator peg underneath the fan duct (top right corner of the fan duct as viewed in the pictures). When reinstalling look down the screw hole to aid alignment.

  46. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    XBOX 360 Hauptplatine ersetzen: Schritt 46, Bild 1 von 2 XBOX 360 Hauptplatine ersetzen: Schritt 46, Bild 2 von 2
    • Remove the single 9.2 mm T10 Torx screw securing the hard drive cable connector to the plastic bracket.

    • Lift the hard drive cable connector off the hard drive bracket.

  47. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    XBOX 360 Hauptplatine ersetzen: Schritt 47, Bild 1 von 1
    • Remove the 11.3 mm T10 Torx screw holding the hard drive bracket to the metal frame, near the DC-In port.

  48. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    XBOX 360 Hauptplatine ersetzen: Schritt 48, Bild 1 von 1
    • Lift the hard drive bracket out of the metal frame.

  49. XBOX 360 Hauptplatine ersetzen: Schritt 49, Bild 1 von 1
    • Entferne das Lüfterkabel, indem du den Stecker vom Mainboard abziehst.

  50. XBOX 360 Hauptplatine ersetzen: Schritt 50, Bild 1 von 3 XBOX 360 Hauptplatine ersetzen: Schritt 50, Bild 2 von 3 XBOX 360 Hauptplatine ersetzen: Schritt 50, Bild 3 von 3
    • Entferne die zwei 11,7 mm Kreuzschlitzschrauben, mit denen der Lüfter am Kühlkörper befestigt ist.

    • Entferne den Lüfter vom Mainboard.

  51. XBOX 360 Hauptplatine ersetzen: Schritt 51, Bild 1 von 1
    • Das Mainboard ist mit insgesamt zehn Schrauben im Metallgehäuse befestigt:

    • Fünf 11,3 mm silberne T10 Torx Schrauben, in den mit "M", "N", "P", "R" und "T" markierten Löchern.

    • Vier 5,6 mm schwarze T9 Torx Schrauben, in den mit "D", "E", "J" und "K" markierten Löchern.

    • Eine einzelne 11,3 mm goldene T10 Torx Schraube, in dem mit "A" markierten Loch.

  52. XBOX 360 Hauptplatine ersetzen: Schritt 52, Bild 1 von 2 XBOX 360 Hauptplatine ersetzen: Schritt 52, Bild 2 von 2
    • Hebe den Haltebügel des optischen Laufwerks vom Mainboard ab.

  53. XBOX 360 Hauptplatine ersetzen: Schritt 53, Bild 1 von 2 XBOX 360 Hauptplatine ersetzen: Schritt 53, Bild 2 von 2
    • Greife den Kühlkörper mit einer Hand, und halte den Rahmen mit der anderen Hand fest.

    • Hebe die Mainboard-Einheit aus dem Metallrahmen heraus.

    • Du wirst ein wenig Kraft aufwenden müssen, um das Mainbaord zu entfernen.

  54. XBOX 360 Hauptplatine ersetzen, Kühlkörper: Schritt 54, Bild 1 von 2 XBOX 360 Hauptplatine ersetzen, Kühlkörper: Schritt 54, Bild 2 von 2
    • Drehe das Logic Board um, um an die X-Klemme des Kühlkörpers zu gelangen.

    • Um ESD-Schäden zu vermeiden, solltest du dein Logic Board während der Wartung auf eine weiche, statische Oberfläche legen.

    • Das Logic Board ist sehr empfindlich gegen Stöße und Kratzer. Achte darauf, dass der Schraubendreher nicht verrutscht und das Logic Board beschädigt wird.

    • Beginnen Sie an der vorderen linken Ecke der x-Klemme und stecken Sie einen 1,5-mm-Schlitzschraubendreher zwischen den Stift des Kühlkörpers und den Haken der x-Klemme.

    • Wenn du dir Sorgen machst, dass du das Logic Board zerkratzen könntest, führe einen "Plastikspatel" (Als Abstandhalter) oder einen dünnen Schraubendreher durch eines der Löcher in der X-Klemme in den Spalt direkt im Schraubenstift. Heble nach außen, um die X-Klemme zu lösen. Wiederholen Sie den Vorgang für den anderen Arm.

  55. XBOX 360 Hauptplatine ersetzen: Schritt 55, Bild 1 von 2 XBOX 360 Hauptplatine ersetzen: Schritt 55, Bild 2 von 2
    • Drehe das Logic Board um 90Grad im Uhrzeigersinn.

    • Lösen Sie auf die gleiche Weise wie oben beschrieben den hinteren rechten Haken der X-Klemme.

  56. XBOX 360 Hauptplatine ersetzen: Schritt 56, Bild 1 von 2 XBOX 360 Hauptplatine ersetzen: Schritt 56, Bild 2 von 2
    • Drehe das Logic Board um 180 Grad gegen den Uhrzeigersinn.

    • Lösen Sie auf die gleiche Weise wie oben beschrieben den hinteren linken Haken der X-Klemme.

  57. XBOX 360 Hauptplatine ersetzen: Schritt 57, Bild 1 von 2 XBOX 360 Hauptplatine ersetzen: Schritt 57, Bild 2 von 2
    • Hebe die X-Klemme von der Rückseite des Logic Boards ab.

  58. XBOX 360 Hauptplatine ersetzen: Schritt 58, Bild 1 von 2 XBOX 360 Hauptplatine ersetzen: Schritt 58, Bild 2 von 2
    • Verwende eine Hand, um den Kühlkörper an Ort und Stelle zu halten, und drehe das Logic Board vorsichtig um.

    • Hebe den Kühlkörper vom Logic Board.

    • Befolgen Sie vor dem Wiederzusammenbauen unsere Leitfaden für Wärmeleitpaste, um die Wärmeleitpaste zwischen Kühlkörper und Prozessor auszutauschen.

  59. XBOX 360 Hauptplatine ersetzen, Hauptplatine/Mainboard: Schritt 59, Bild 1 von 1
    • Das Logic Board und seine Anschlüsse bleiben erhalten.

    • Wenn Sie eine neue Platine neu installieren, entfernen Sie die Kabel von dieser Platine und legen Sie sie auf die neue Platine.

Abschluss

Um dein Gerät wieder zusammenzubauen, folge der Anleitung in umgekehrter Reihenfolge.

115 weitere Nutzer:innen haben diese Anleitung absolviert.

David Hodson

Mitglied seit: 04/13/10

150.352 Reputation

127 Anleitungen geschrieben

9 Kommentare

This guide wouldn't even work. DVD drives are linked to the motherboard. If someone were to follow this the end result would be an Xbox console that could only play DVDS games would show up as DVDs because of key mismatch.

Adam - Antwort

What you mean “could only play DVDS games would show up as DVDs because of key mismatch “?

Whats the difference you mean about DVDS and DVDs?

Enio Freitas -

Yes, but this is a good guide for those that are installing new thermal paste on their boards and/or wanna gut their system for a thorough cleaning.

the bongo guy -

just wanted to say thank you although i only needed up to step 43 as i'm have issues with the dvd drive it seems it only wants to read if the drive case is open my my thought is the slider servo is about done for. the dvd was a bit of a bear to figure out for a few minutes but remove the foam then use a p42 driver on the screws underside then the top slides off the back and honestly i left the bottom on.i found step 29 to be a bit of a pain and almost decided to break that bugger of a clip off for future work but didn't, and to me it seemed that removing the screws in step 40 made steps 32 through 34 easier, i don't know take it for what it's worth also i found i could also skip step 35 and leave the front plate and the rf module connected which made working the unit while open/disassembled easier if you need to remove the rf module then you can move the front plate off to the side enough and remove the screws holding it, and beside i hate working with ribbon cable. all in all nice guide though THUMBS UP!

jinarion - Antwort

Thanks mate, got me to where I needed to get to… that other tosser can !#^& off tho, id like to see him take the time and effort to produce a detailed instructional like this.

Paul Hayes - Antwort

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 17

Letzte 7 Tage: 161

Letzte 30 Tage: 604

Insgesamt: 134,346