Einleitung
Tausche die Trigger an deinem Xbox One Controller aus.
Was du brauchst
-
-
Drücke den Knopf am Batteriefach oben am Controller.
-
Entferne das Batteriefach vom Controller.
-
-
-
Benutze eine Pinzette, um den Barcode-Aufkleber aus dem Batteriefach abzulösen.
-
-
-
Entferne die sieben 9,3 mm T8 Security Torx Schrauben, welche das rückwärtige Gehäuse an das vordere befestigen.
Any recommendation on which set of Security Torx tools to use? I've already purchased 2 kits, one of those being sold as "Xbox controller tools" but the diameter of the head does not fit the hole on the controller and that's critical for the 2 screws on the bottom. The tools must obviously be thinner in diameter and long enough to get there.
How to open an XBOX 360 controller without a special screwdriver. http://www.instructables.com/id/How-to-o... Works perfectly.
A lot of thanks for your comment. It's very usefull
Echedey -
I picked up a handy torx key set from Auto Zone. Was about $10, no lose driver bits. has both sizes you need to repair the controller and the console. Here's the link:
It doesn't really matter which set of bits you by or what brand makes them, Torx bits (and the security versions of them) are generic & come in standardized sizes. You do not need a special "xbox" tool kit, you just need a size 8 torx security bit, no matter what brand makes the bit/kit. Those types of "specialty kits" are usually just collections of generic bits that you can buy at a hardware store in a regular bit set. The difference is that a general bit set will have bits for screws that a specific item doesn't have in it, whereas a specialty kit will only include bits for the types & sizes of fasteners used in the specified item.
BTW, with the smaller sizes of torx security bits you can try breaking off the little post in the middle with needlenose pliers or something else that can fit in the there. Even if the post doesn't break off cleanly, it's usually short enough to fit a regular (non security) torx bit in the slot.
-
-
-
Führe einen weiteren Spudger zwischen das rückwärtige und das vordere Gehäuse, nahe des Kopfhöreranschlusses, ein.
-
Drehe den Spudger in Richtung der Vorderseite des Controllers, um die beiden Gehäuseteile voneinander zu trennen.
-
-
-
-
Halte den Controller am Batteriefach und am Kopfhöreranschluss.
-
Hebe das Batteriefach weg vom Kopfhöreranschluss und trenne so das rückwärtige Gehäuse vom vorderen Gehäuse sowie dem Logic Board.
Good information
-
-
-
Hebe das Kabel des Vibrationsmotors mit dem flachen Ende eines Spudger aus dem Anschluss auf dem Logic Board nach oben und trenne es ab.
-
Hebe den Vibrationsmotor aus dem vorderen Gehäuse heraus.
-
-
-
Entferne auf gleiche Weise den Vibrationsmotor von der anderen Seite des Controllers.
The opposite was true for the controller I just opened. It was the left motor counterweight (as you hold the controller normally) which had more weight. Perhaps it doesn't matter which goes where?
For anyone reading this in the future, it does matter. The way you had them originally is the correct way.
-
-
-
Fasse das Logic Board an der Kopfhörerbuchse und Versorgungsbuchse an, hebe es hoch und entferne es vom vorderen Gehäuse.
What if you're having difficulty taking the logic board out?
-
-
-
Drücke den linken Trigger mit dem Daumen und dem Zeigefinger zur rechten Seite des Controllers hin. Drücke gleichzeitig den Kontrollhebel des Triggers in die entgegengesetzte Richtung.
-
Drücke den Triggerhebel nach unten.
-
-
-
Setze die Kante eines Spudgers zwischen den Trigger und die Triggereinheit nahe an der linken Kante ein. Heble die Fassung von ihrer Aufhängung auf dem Trigger weg.
-
Heble in gleicher Weise die Fassung an der rechten Kante vom Trigger weg.
-
Drehe den Trigger vom Logic Board weg und an seiner Fassung vorbei.
-
-
-
Heble mit einem Spudger die Feder im Trigger von ihrem Stift auf der Fassung weg.
-
Ziehe die Feder aus dem Trigger heraus.
-
-
-
Schiebe den Trigger zur rechten Seite des Logic Boards hin und drehe ihn gegen den Uhrzeigersinn.
-
Entferne den rechten Trigger vom Logic Board.
This is a removal guide not a replacement guide. I need steps to putting the trigger back in now.
My trigger works by moving in and out but it is constantly either working or constantly not, when i press the home screen it switches between the two……help please
-
Um dein Gerät wieder zusammenbauen, folge den Schritten in umgekehrter Reihenfolge.
Um dein Gerät wieder zusammenbauen, folge den Schritten in umgekehrter Reihenfolge.
Rückgängig: Ich habe diese Anleitung nicht absolviert.
45 weitere Nutzer:innen haben diese Anleitung absolviert.
Besonderer Dank geht an diese Übersetzer:innen:
100%
Diese Übersetzer:innen helfen uns, die Welt zu reparieren! Wie kann ich mithelfen?
Hier starten ›
5 Kommentare
use a small tag of double sided tape to hold the counterweights in when you rebuild or its nearly impossible to tip up the two halfs of the controller to fit them together. With the counterweight just slightly stuck into place with a tiny tag of double sided tape you can tip that half of the controller upside down to fit on top of the other half. Still awkward but do-able. Almost impossible otherwise.
If i leave out the vibrations things will it cause the problems tonthe board ??
These instructions were given in proper order and understanding
IMO this could have benefited from some instructions on how to get the triggers back on, cause it was quite a challenge.
The way I managed to do it, is you've got to reverse both step 11 and step 10 in one go, otherwise it would be impossible to get the trigger peg into the white arm (at least I couldn't figure out a way to do it): before reversing step 11, hold the white arm up and to same side you pushed it in the step 10, and then once you click it back into place, the peg would also go into the slot in the arm. For me it was easier to do for LT than RT - the latter too a few tries, so I would recommend doing LT first and then RT.