Zum Hauptinhalt wechseln
  1. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    Turn the controller on its backside and push the "eject" button to discharge the battery compartment door on the bottom of the controller. Pull the two AA batteries out.
    • Turn the controller on its backside and push the "eject" button to discharge the battery compartment door on the bottom of the controller.

    • Pull the two AA batteries out.

  2. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    Remove the holographic Microsoft sticker with the percision tweezers to reveal a small screw. Use a T6 Torx screwdriver to remove the 1.5mm screw.
    • Remove the holographic Microsoft sticker with the percision tweezers to reveal a small screw.

    • Use a T6 Torx screwdriver to remove the 1.5mm screw.

  3. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    Insert a spudger and pry at these three locations to detach the middle cover. Pull off the middle piece cover to reveal three screws. Use a T8 Torx screwdriver to remove the three 2.3mm screws.
    • Insert a spudger and pry at these three locations to detach the middle cover.

    • Pull off the middle piece cover to reveal three screws.

    • Use a T8 Torx screwdriver to remove the three 2.3mm screws.

    • Remove the cover.

  4. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    Remove the two 90mm screws with a T8 Torx screwdriver. Lift up the silver middle piece to remove. Lift up the silver middle piece to remove.
    • Remove the two 90mm screws with a T8 Torx screwdriver.

    • Lift up the silver middle piece to remove.

  5. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    Use a spudger to remove the silver prong. With the spudger, pinch the metal spring and slowly pull up to remove. Use the spudger to remove eject button.
    • Use a spudger to remove the silver prong.

    • With the spudger, pinch the metal spring and slowly pull up to remove.

    • Use the spudger to remove eject button.

    • Remove the screw holding in the eject button with a T8 Torx screwdriver.

  6. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    This step is very difficult and may require a third hand. Pull the two halves apart at the bottom to detach the two latches that are holding the front and back panels together. Start with one side of the controller (left or right).
    • This step is very difficult and may require a third hand.

    • Pull the two halves apart at the bottom to detach the two latches that are holding the front and back panels together.

    • Start with one side of the controller (left or right).

    • Slide the spudger towards the end of the handles and pry the two halves apart. Do the same for the opposite side.

    • The white circular caps at the top of the controller will pop off by applying light force.

    • Pull the front and back panels apart to separate them and expose the inside of the controller.

  7. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    Lift the battery compartment out of the controller and set it outside of the controller. Do not yank, stress, or pull on the wires for removal. Use the precision tweezers to pull out the red and black wire attached to the white plug at the bottom side of the circuit board.
    • Lift the battery compartment out of the controller and set it outside of the controller.

    • Do not yank, stress, or pull on the wires for removal.

    • Use the precision tweezers to pull out the red and black wire attached to the white plug at the bottom side of the circuit board.

Ziellinie

Team

USF Tampa, Team S16-G5, Boczar Spring 2018 Mitglied von USF Tampa, Team S16-G5, Boczar Spring 2018

USFT-BOCZAR-S18S16G5

5 Mitglieder

8 Anleitungen geschrieben

0 Kommentare

Kommentar hinzufügen

Seitenaufrufe:

Letzten 24 Stunden: 0

Letzten 7 Tage: 6

Letzten 30 Tage: 46

Insgesamt: 1,416