Repariere deine Sachen Community Store

Xbox One S IR Blaster Replacement

Einleitung

If your Xbox One S is not picking up motion signals when playing certain games follow this guide to replace your IR blaster. Make sure to check that you are within line of sight of the front of the Xbox One S and there is no barrier between the user and the device.

Was du brauchst

  1. Xbox One S IR Blaster Replacement, Case: Schritt 1, Bild 1 von 1

    • Flip the Xbox One S so that the bottom of the case is facing upward.

    Übersetzen

  2. Xbox One S IR Blaster Replacement: Schritt 2, Bild 1 von 1

    • Begin by working at the case on the rear where the warranty sticker is located. Insert the plastic opening tool into the gap between the bottom of the case and the grated top side. Then find the clips in between that hold the case in place. Use the opening tool to pop the clips out. The best method is to pry the black case away from the bottom.

    • Use the opening tool to pop the clips out. The best method is to pry the black case away from the bottom.

    • You will hear clicking sounds when you are prying the case open. It may be fairly difficult to remove the bottom.

    • It's possible that the clips may break when you remove the bottom from the case.

    • We recommend starting at the back where the warranty sticker is located. Pry along the rear edge until all clips are free. From there do each side. When three sides are free start at the end of the front opposite the sync button. Be cautious and take your time and all should separate without any damage.

    Übersetzen

  3. Xbox One S IR Blaster Replacement: Schritt 3, Bild 1 von 1

    • Once all of the clips are opened, remove the bottom part of the case.

    Übersetzen

  5. Xbox One S IR Blaster Replacement: Schritt 4, Bild 1 von 2 Xbox One S IR Blaster Replacement: Schritt 4, Bild 2 von 2

    • Use a T10 Torx screwdriver to remove the six green 50 mm long screws from the metal case labeled F1 through F6.

    Übersetzen

  6. Xbox One S IR Blaster Replacement: Schritt 5, Bild 1 von 2 Xbox One S IR Blaster Replacement: Schritt 5, Bild 2 von 2

    • Gently separate the interior case from the white exterior case using the appropriate method.

    • Pry the white plastic sides outwards at the rear to separate from the plastic I/O shield

    Übersetzen

  7. Xbox One S IR Blaster Replacement, IR Blaster: Schritt 6, Bild 1 von 1

    • The IR blaster can be identified on one of the sides of the interior case. It will be next to the disc drive and near the fan.

    Übersetzen

  8. Xbox One S IR Blaster Replacement: Schritt 7, Bild 1 von 1

    • Use a Torx T8 screwdriver to remove the four 15mm screws with orange circles around them.

    • After the screws are removed gently pull the IR blaster off the case.

    Übersetzen
Abschluss

To reassemble your device, follow these instructions in reverse order.

15 weitere Nutzer:innen haben diese Anleitung absolviert.

Autor:in

mit 7 anderen Mitwirkenden

Christopher Chen

Mitglied seit: 04/26/17

627 Reputation

2 Anleitungen geschrieben

Auszeichnungen: 12

+ 9 weitere Auszeichnungen

Team

Cal Poly, Team S22-G3, Livingston Spring 2017 Mitglied von Cal Poly, Team S22-G3, Livingston Spring 2017

CPSU-LIVINGSTON-S17S22G3

4 Mitglieder

56 Anleitungen geschrieben

2 Kommentare

When the board gets replaced does the power light still function normally? I just replaced one because a power button failed and while the new switches work the indicator lights will not power on

Brandon Shrader - Antwort

Question. What's size and type of button does this board use? I have one with the eject and sync button sheered off.

Frank urmom - Antwort

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 1

Letzte 7 Tage: 11

Letzte 30 Tage: 63

Insgesamt: 5,552