Einleitung
Schultertasten an einem Xbox One Wireless Controller 1697 können im Laufe der Zeit aufgrund längerer Nutzung weniger empfindlich werden. Wenn die Trigger an deinem Controller mit der Zeit locker werden oder brechen, verwende diese Anleitung, um die Schultertasten am Controller zu ersetzen.
Was du brauchst
-
-
Entferne die Abdeckung des Batteriefachs.
-
Entferne die beiden AA-Batterien.
-
Entferne den Aufkleber vorsichtig oder mache ein Loch an der Stelle, an der man die Schraube ertasten kann.
-
-
-
Entferne die seitlichen Griffe, indem du den Spudger um die Seitenabdeckungen herum einkeilst.
-
Hebe die Seitenabdeckung an, indem du den Spudger hin und her bewegst. Mach das entlang der gesamten Fuge, um das seitliche Griffteil zu entfernen.
-
Um die Abdeckungen der beiden Handgriffe zu entfernen, müssen jeweils sieben Klammern gelöst werden.
Absolutely use the spudger to do this. DO NOT just lift up a bit at the bottom and then try to forcefully pull off this panel (as is shown and suggested on *multiple* YouTube videos). You WILL snap the clips. Maybe not all of them and *maybe* none of them, but as the instructions here detail, what you want to do is UNCLIP the clips where they are located, using the PLASTIC spudger. NOT a screwdriver. I watched three separate videos on YouTube where the person said “just stick a screwdriver in there and once you’re able to lift up enough to fit your finger inside, do so, and then just carefully pull the panel off.” That’s not how it works.
-
-
-
-
Benutze einen TORX TR8 Schraubendreher Grösse 8, um die fünf Torxschrauben TR9 zu entfernen.
you must also remove the T8 screw hidden under the label in the battery compartment to free the faceplate.
Precised by Dennis Kim, but to remove the screws you need a TORX TR8 screwdriver (I guess it’s a Torx size 8)
-
-
-
Die Schultertasten sind durch eine Kunststoffabdeckung in der Mitte verbunden, die sich um den Xbox-Home-Button herum befindet. Entferne dieses Kunststoffteil, indem du die Kunststoffabdeckung über die beiden Stifte hebst, den Home-Button hineindrückst und die Abdeckung in Richtung Oberseite des Controllers ziehst.
-
Achte auf den Sync-Button, der lose unter die Plastikabdeckung gesetzt ist. Vergewissere dich, dass er wieder an Ort und Stelle ist, bevor du die Schultertasten/Kunststoffabdeckung wieder anbringst.
-
Entferne die alte Schultertasten-Einheit, indem du sie von der Kunststoffabdeckung abziehst.
you forgot to include directions for removing the central cover.
And when you do, the connect button pops out, and now I have no clue how to put it back -_-
The replacement part I bought fit OK but was too snug, with the result that the bumpers wouldn’t spring back so they wouldn’t click and unclick the tiny control switches they connect to.
After a bit of examination I determined that if I cut out the middle arch section that joins the bumpers, but leaving enough plastic to go under the central plastic cover so that they would be held in place securely, that it was possible to reassemble the controller so the bumpers click and unclick freely.
I had the same issue, But i just shaved the little lugs that connect the button to the switch with a scalpel and used the original plastic black cover. Works a treat and i’ve no fear the button will fall out.. :)
-
-
-
Richte die neuen Schultertasten auf der Oberseite des Controllers aus, indem du die Trigger gedrückt hältst und die vier Stifte auf beiden Seiten ausrichtest.
-
Setze die neue Abdeckung des Home-Button über den Mikro-USB-Anschluss, drücke den Home-Button hinein und ziehe die Abdeckung über die beiden abgebildeten Stifte.
-
Dein Gerät ist nun einsatzbereit.
Dein Gerät ist nun einsatzbereit.
Rückgängig: Ich habe diese Anleitung nicht absolviert.
60 weitere Nutzer:innen haben diese Anleitung absolviert.
Besonderer Dank geht an diese Übersetzer:innen:
100%
Diese Übersetzer:innen helfen uns, die Welt zu reparieren! Wie kann ich mithelfen?
Hier starten ›
12 Kommentare
You should add a security hex screwdriver to your tools list, along with the gauge that is required.
There is a fifth screw in the battery compartment that holds the faceplate on. Take an exacto knife and cut out sticker where the hole is.
Could you elaborate on the “remove the bumpers” part (last step) please, thank you.
Great guide. Helped me easily fix a sticky bumper and save 60$
Thank you soooo much. Had a broken bumper for over a year and finally fixed it thanks to this great guide.
How do you put them back on. The right button assembly seems to be different than the left for me
Bad design or planned obsolescence on Microsoft's part, but thanks for the guide. I had a problem that others had on the replacement bumper where it had the switch depressed all the time, their solution was to file down the plastic (just barely) that presses the switch and it worked for me as well.
Excellent guide! Just revived a controller that had been chilling unused for 2 years. The replacement bumper I purchased off of Ebay had a little hitch. They would not move or click at all when placed. I just had to break off the little plastic nub that holds the end of the bumper to the controller (I found that little trick on accident by breaking one of them, lol). Now the controller functions fine, the bumpers can just be pulled up at the outside ends. Not a problem, as their purpose is to be clicked. Thanks!
Note: Screw removal is in Step 3
jkgarrett17 - Antwort