Zum Hauptinhalt wechseln

Xbox One Wireless Controller Steuerkreuz Austausch

Was du brauchst

  1. Xbox One Wireless Controller Steuerkreuz Austausch, Akku: Schritt 1, Bild 1 von 1
    • Entferne den Akkudeckel

    • Entnimm den Akku

  2. Xbox One Wireless Controller Steuerkreuz Austausch, Seitenteile: Schritt 2, Bild 1 von 2 Xbox One Wireless Controller Steuerkreuz Austausch, Seitenteile: Schritt 2, Bild 2 von 2
    • Im Foto ist ein Metallspudger zu sehen. Wir empfehlen einen Spudger aus Plastik.

    • Nimm den Controller fest in die Hand um die Seitenteile abzunehmen. Heble mit einem Spudger in die Naht zwischen Front- und Seitenteil.

    • Ziehe das Seitenteil ab indem du den Spudger vor und zurück bewegst. Das musst du entlang der ganzen Naht durchführen.

    Start prying the side plate off underneath the trigger, this makes it easier to disconnect the other clips connecting the side plate to the backplate.

    Brandon - Antwort

    One you take it off, is it possible to click it back in?

    Aiden Bear - Antwort

    As long as you don’t exceed the couple tons you need to take it off you should be able to put it back.

    Brandon -

    I don’t have a squdger

    TimidFerret4982 Gaming - Antwort

    getting those handles back on seems impossible, they just dont fit as well, a gap remains even after snapping into place.

    Dont think ill be doing this in the future

    Spoutin Wyze - Antwort

    edit: wiggled the bo9ttom middlewith the handles off and somethign finally “clicked” into place for that extra 1/4 mm for the down arrow on my D-Pad to click back up into place!.

    Spoutin Wyze - Antwort

  3. Xbox One Wireless Controller Steuerkreuz Austausch, Schrauben: Schritt 3, Bild 1 von 2 Xbox One Wireless Controller Steuerkreuz Austausch, Schrauben: Schritt 3, Bild 2 von 2
    • Hinter einem Aufkleber in der Mitte des Controllers ist eine Schraube verborgen.

    • Mit einem Schraubendreher kannst du ein Loch direkt in die Mitte des Aufklebers stoßen.

    • Wenn du den Aufkleber nicht verletzen willst kannst du ihn auch vorsichtig anheben.

    • Entferne die fünf 10 mm Torx TR8 Sicherheitsschrauben auf der Rückseite.

    i damaged my screws. how do i get the screws out?

    tenzin - Antwort

    wait. i just watched a video guide on ifixit's youtube channel about damaged screws. i'll try those methods.

    tenzin - Antwort

    It's a t8 or t9 security bit btw, I got the top two out with a regular T8, but the bottom two and middle needed a T9 Security bit.

    David Loper - Antwort

    All five faceplate/backplate screws in the controller I disassembled were T8 security fasteners.

    John Dziedzic - Antwort

    Am I doing something wrong because I got the tool it said I needed and got the middle screw out but the others have a bump or something in the center of the screw and it won't fit.

    kolton77 - Antwort

    The T8 is only good for the middle screw on my One S controller. The others require something bigger

    Matej Skelo - Antwort

    These requires SECURITY Torx bits (they have a cannulated hole in the driver). I don't believe the iFixIt branded driver is cannulated but you can buy a set of bits from DeWalt DWAX200 which is overkill but has what you need.

    jhighsmith - Antwort

    The driver that iFixIt sells is cannulated.

    jhighsmith -

    where do you get this dumb ass screw driver

    Jake Zweier - Antwort

    iFixit Store #IF145-027-3

    VauWeh - Antwort

    You can bypass it with a 1.5mm flathead.

    Marianne Sandling - Antwort

    thank you for this. worked for me

    Mr Anderson (Evolluisionist) -

    These screws required a T10, not T8.

    Armand - Antwort

    TR9. A $10 kit from Walmart has the bit/driver in it and extra goodies to make life simple.

    Matt Martin - Antwort

    As weird as it sounds, the top 2 came out for me with a flathead- but the bottom two and the middle one wont

    macybrooksevans - Antwort

    If you damage the middle part of the screws you can still take it out with the same screwdriver.

    Kev God - Antwort

    Thank-You :)

    Isaiah - Antwort

    needed a T8H, not easy to see.

    on a grey green xbox one controller

    Michael - Antwort

    On my 1708 controller there are two internal screws near the rumble motors that need to be removed with a T6 non security bit to remove the back cover.

    teeedubb - Antwort

  4. Xbox One Wireless Controller Steuerkreuz Austausch, Rückseite: Schritt 4, Bild 1 von 1
    • Nimm die Rückseite ab.

  5. Xbox One Wireless Controller Steuerkreuz Austausch, Frontplatte: Schritt 5, Bild 1 von 1
    • Entferne die Frontplatte.

  6. Xbox One Wireless Controller Steuerkreuz Austausch, Metallrahmen: Schritt 6, Bild 1 von 2 Xbox One Wireless Controller Steuerkreuz Austausch, Metallrahmen: Schritt 6, Bild 2 von 2
    • Hebele den Metallrahmen um das Steuerkreuz ab.

  7. Xbox One Wireless Controller Steuerkreuz Austausch, Steuerkreuz: Schritt 7, Bild 1 von 1
    • Hebe das Steurkreuz aus seinem Sitz.

Abschluss

Um dein Gerät wieder zusammen zu setzen folge den Schritten in umgekehrter Reihenfolge.

44 weitere Nutzer:innen haben diese Anleitung absolviert.

Besonderer Dank geht an diese Übersetzer:innen:

en de

100%

VauWeh hilft uns, die Welt in Ordnung zu bringen! Wie kann ich mithelfen?
Hier starten ›

Garrett George

Mitglied seit: 01/22/15

6.151 Reputation

3 Anleitungen geschrieben

Team

Cal Poly, Team 20-15, Maness Winter 2015 Mitglied von Cal Poly, Team 20-15, Maness Winter 2015

CPSU-MANESS-W15S20G15

5 Mitglieder

50 Anleitungen geschrieben

7 Kommentare

Can you show me how to replace xbox one controller 3.5mm stereo jack dpad

Arief Hidayat - Antwort

This model of the xbox one controller does not feature a 3.5mm headphone jack. Please look at the guides for later models of the xbox one controller.

Brandon -

it's exactly the same like shown above :)

David Schmidt - Antwort

How do u fix one of the silver things behind the d-pad?

Bob - Antwort

How do fix the silver things behind each d-pad

Bob - Antwort

I had a unresponsive left-button on my D-pad. It worked consistently only if I pressed very hard. l fixed mine, not with a new D-pad, but by adding a few layers of plastic tape over the press-sensitive “cushion” (the one that the button plastic part of the left d-pad should trigger). That made it much more responsive. It feels slightly different pressing down on the button now, but I can live with that trade-off.

john lastson - Antwort

Como arreglo las teclas además de desmontar se puede arreglar cada botón?

isaac barreto - Antwort

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 7

Letzte 7 Tage: 61

Letzte 30 Tage: 268

Insgesamt: 62,862