Zum Hauptinhalt wechseln

Xbox One X Festplatte tauschen

Was du brauchst

Einführungsvideo

  1. Xbox One X Festplatte tauschen, Aufkleber entfernen: Schritt 1, Bild 1 von 2 Xbox One X Festplatte tauschen, Aufkleber entfernen: Schritt 1, Bild 2 von 2
    • Ziehe mit einer stumpfen Pinzette den Aufkleber ab, der die rechte Schraube auf der Rückseite der Konsole bedeckt.

    • Bevor du mit dieser Anleitung beginnst: Schalte das Gerät aus. Ziehe dann alle Kabel von der Konsole ab.

  2. Xbox One X Festplatte tauschen, Äußeren Schrauben entfernen: Schritt 2, Bild 1 von 1
    • Entferne die beiden 12,6 mm Torx T10 Schrauben auf der Rückseite der Konsole.

  3. Xbox One X Festplatte tauschen, Gehäuseoberseite waagrecht schieben: Schritt 3, Bild 1 von 2 Xbox One X Festplatte tauschen, Gehäuseoberseite waagrecht schieben: Schritt 3, Bild 2 von 2
    • Drehe die Konsole um 90 Grad.

    • Ziehe die Vorderseite der Gehäuseoberseite waagrecht zur Vorderseite der Konsole, bis sie zum Stillstand kommt. Dadurch werden die Clips aus den Schlitzen der Gehäuseoberseite herausgeschoben.

  4. Xbox One X Festplatte tauschen, Gehäuseoberseite anheben: Schritt 4, Bild 1 von 2 Xbox One X Festplatte tauschen, Gehäuseoberseite anheben: Schritt 4, Bild 2 von 2
    • Drehe die Konsole um 90 Grad, sodass die Rückseite zu dir zeigt.

    • Hebe die linke Seite der Gehäuseoberseite an (von der Rückseite der Konsole aus gesehen) und stoppe, wenn es sich nicht weiter anheben lässt.

  5. Xbox One X Festplatte tauschen: Schritt 5, Bild 1 von 3 Xbox One X Festplatte tauschen: Schritt 5, Bild 2 von 3 Xbox One X Festplatte tauschen: Schritt 5, Bild 3 von 3
    • Halte die linke Seite der Gehäuseoberseite weiterhin fest und drücke die rechte Seite nach oben, um die rechte Schraubennabe aus dem Weg zu räumen.

    • Wenn das Hochdrücken des Gehäuses nicht funktioniert, versuche, es in verschiedene Richtungen zu bewegen, bis es aufschwingt.

    • Klappe das obere Kunststoffgehäuse auf 75 Grad auf.

  6. Xbox One X Festplatte tauschen: Schritt 6, Bild 1 von 2 Xbox One X Festplatte tauschen: Schritt 6, Bild 2 von 2
    • Drücke die Gehäuseoberseite nach unten und von der Konsole weg, um es vollständig zu entfernen.

    I found this step a little hard to complete. I flipped down the lock and then removed the screws. The ribbon came out much easier that way.

    metric - Antwort

  7. Xbox One X Festplatte tauschen, Flachbandkabel abtrennen: Schritt 7, Bild 1 von 3 Xbox One X Festplatte tauschen, Flachbandkabel abtrennen: Schritt 7, Bild 2 von 3 Xbox One X Festplatte tauschen, Flachbandkabel abtrennen: Schritt 7, Bild 3 von 3
    • Verwende das spitze Ende eines Spudgers, ein Öffnungswerkzeug oder deinen Fingernagel, um die kleine, schwenkbare Verriegelungsklappe am ZIF-Anschluss des Flachbandkabels auf der vorderen Leiterplatte herunterzuklappen.

  8. Xbox One X Festplatte tauschen, Flachbandkabel abtrennen: Schritt 8, Bild 1 von 1
    • Ziehe das Flachbandkabel mit einer stumpfen Pinzette aus dem Stecker.

    What happens if I broke the connector to the ribbon cable ?

    Brandon LittleHawk - Antwort

    If you broke the cable, then one Wifi module would be broken.

    Alex Barblexi -

    Why we dont remove at first the 3 screws and lift the board a little bit, before removing the cable completely?

    Alex Barblexi - Antwort

  9. Xbox One X Festplatte tauschen, Entferne die Schrauben der vorderen Platine: Schritt 9, Bild 1 von 1
    • Entferne die drei 13,3 mm Torx T8 Schrauben, mit denen die vordere Platine am oberen Metallgehäuse befestigt ist.

    How crucial and important is this step? I ovwrlooked it when doing this. Will this mess it all up?

    Ozzy Hernandez - Antwort

  10. Xbox One X Festplatte tauschen, Entfernen der vorderen Platine: Schritt 10, Bild 1 von 2 Xbox One X Festplatte tauschen, Entfernen der vorderen Platine: Schritt 10, Bild 2 von 2
    • Ziehe die vordere Leiterplatte gerade aus dem oberen Metallgehäuse heraus und lege sie beiseite.

    • Fasse die Platine an beiden Seiten dort an, wo sie eingesteckt ist, um zu vermeiden, dass sie verbogen und beschädigt wird.

    During the reassembly process, I highly recommend that you reattach and lock the ribbon cable (steps 7 and 8) before you attach the circuit board. There is plenty of ribbon to work with, and once the circuit board is attached it is nearly impossible to get the ribbon flat and aligned and pushed up into the guide. Obviously be careful you don’t yank the ribbon as you maneuver the circuit board into place, but who’s not being careful while they are doing this?

    Tim Davis - Antwort

  11. Xbox One X Festplatte tauschen, Entfernen der oberen Metallgehäuseschrauben: Schritt 11, Bild 1 von 1
    • Entferne die sechs 47,7 mm Torx T10 Schrauben, mit denen das obere Metallgehäuse am unteren Kunststoffgehäuse befestigt ist.

    • Entferne die beiden 7,5 mm Torx T8 Schrauben, mit denen der Druckverbinder am oberen Metallgehäuse befestigt ist.

    Must remove power supply screws as well

    Kwame Tsunami - Antwort

    Hi, this step only includes the screws needed to remove the lower metal case. Guides that require removing the power supply screws will have a step later on with instructions on which screws to remove.

    Kyle Smith -

    Why we dont't remove the hard drive screws in this step, please?

    Alex Barblexi - Antwort

  12. Xbox One X Festplatte tauschen, Druckstecker lösen: Schritt 12, Bild 1 von 2 Xbox One X Festplatte tauschen, Druckstecker lösen: Schritt 12, Bild 2 von 2
    • Führe das flache Ende eines Spudgers unter den Druckstecker auf der dem Flachbandkabel gegenüberliegenden Seite ein.

    • Hebe den Druckstecker mit dem Spudger vom oberen Metallgehäuse ab.

    • Drücke den Spudger nicht bis zum Anschlag in die Buchse. Ein Hochhebeln der Buchse kann diese beschädigen.

    • Um Druckstecker wie diesen wieder anzubringen, richte ihn vorsichtig aus und drücke ihn auf einer Seite nach unten, bis er einrastet. Wiederhole dies auf der anderen Seite. Drücke nicht auf die Mitte. Wenn der Stecker nicht richtig ausgerichtet ist, können sich die Stifte verbiegen und dauerhaft beschädigt werden.

    I need to know what it calls and I will purchase the one like press connector on the upper metal case.

    Erick Rivera - Antwort

  13. Xbox One X Festplatte tauschen, Gehäuseunterseite entfernen: Schritt 13, Bild 1 von 3 Xbox One X Festplatte tauschen, Gehäuseunterseite entfernen: Schritt 13, Bild 2 von 3 Xbox One X Festplatte tauschen, Gehäuseunterseite entfernen: Schritt 13, Bild 3 von 3
    • Drehe die Konsole um.

    • Halte die Gehäuseunterseite fest, da sie nicht mehr am Metallgehäuse befestigt ist.

    • Hebe die Gehäuseunterseite vom Metallgehäuse ab und lege sie beiseite.

    I had a hard time getting the bottom case back on by trying to slide it over the console. It was easier for me to place the case on the table and guide the hardware into it. There are four holes just above the disc drive that are tricky to line up if you try to slip the case back on.

    metric - Antwort

    When reassembling, ensure that the press connector and the ribbon cable are hanging outside of the chassis so that you can reattach them. The ribbon cable in particular is easy to leave inside of the case where it may get bent and crushed as you reassemble it.

    A.Kulcsar - Antwort

  14. Xbox One X Festplatte tauschen, Entfernen der unteren Metallgehäuseschrauben: Schritt 14, Bild 1 von 1
    • Entferne die beiden Torx T10 Schrauben, mit denen das untere Metallgehäuse befestigt ist:

    • Eine 7,7 mm Schraube

    • Eine 11,4 mm Schraube

    bei mir waren beide Schrauben identisch konnte sie auch komplett versenken

    Evtl. fand vor mir schon ein Austausch statt

    André Schuler - Antwort

  15. Xbox One X Festplatte tauschen, Entfernen des unteren Metallgehäuses: Schritt 15, Bild 1 von 1
    • Hebe das untere Metallgehäuse vom oberen Metallgehäuse und den internen Komponenten ab.

    • Das Laufwerk kann sich gleichzeitig mit dem unteren Metallgehäuse anheben. Halte es während dieses Schritts nach unten gedrückt.

    • Lege das untere Metallgehäuse beiseite.

  16. Xbox One X Festplatte tauschen, Schrauben, mit denen die Festplatte am Gehäuse befestigt ist, entfernen: Schritt 16, Bild 1 von 1
    • Drehe die Konsole um.

    • Das Laufwerk ist nur über zwei Kabelanschlüsse mit dem Motherboard verbunden. Halte das Laufwerk fest, wenn du die Konsole umdrehst, um eine Beschädigung zu vermeiden.

    • Entferne die vier 11,4 mm Schrauben, mit denen die Festplatte am oberen Metallgehäuse befestigt ist, mit einem T10 Torx-Schraubendreher.

    • Drehe dann die Konsole wieder um.

  17. Xbox One X Festplatte tauschen, Laufwerk anheben: Schritt 17, Bild 1 von 3 Xbox One X Festplatte tauschen, Laufwerk anheben: Schritt 17, Bild 2 von 3 Xbox One X Festplatte tauschen, Laufwerk anheben: Schritt 17, Bild 3 von 3
    • Hebe das Laufwerk an, damit die Metalllasche vom Netzteil gelöst wird.

    • Drehe das Laufwerk um und lege es auf das Netzteil. Das Laufwerk sollte in die entgegengesetzte Richtung zeigen, auf dem es vorher lag.

    • Das Laufwerk ist an das Motherboard angeschlossen. Vermeide es, die Kabel mehr als nötig zu ziehen und zu biegen, um Beschädigungen zu vermeiden.

  18. Xbox One X Festplatte tauschen, Stecker des Kabelbündels abziehen: Schritt 18, Bild 1 von 2 Xbox One X Festplatte tauschen, Stecker des Kabelbündels abziehen: Schritt 18, Bild 2 von 2
    • Ziehe den Stecker des Kabelbündels ab, der die Festplatte mit dem Motherboard verbindet, indem du gerade nach oben ziehst.

  19. Xbox One X Festplatte tauschen, SATA-Kabel abziehen: Schritt 19, Bild 1 von 2 Xbox One X Festplatte tauschen, SATA-Kabel abziehen: Schritt 19, Bild 2 von 2
    • Ziehe das SATA-Kabel ab, das die Festplatte mit dem Motherboard verbindet, indem du es gerade nach oben ziehst.

    I had a hard time unplugging this connector. I left it plugged in and replaced the drive.

    metric - Antwort

  20. Xbox One X Festplatte tauschen, Festplatte entfernen: Schritt 20, Bild 1 von 2 Xbox One X Festplatte tauschen, Festplatte entfernen: Schritt 20, Bild 2 von 2
    • Hebe die Festplattenbaugruppe nach oben aus dem oberen Metallgehäuse.

    • Halte die Festplatte dabei an den Seiten fest, um Beschädigungen zu vermeiden.

  21. Xbox One X Festplatte tauschen, Montagehalterung entfernen: Schritt 21, Bild 1 von 1
    • Drehe die Festplatte um, so dass die Gehäusehalterung aus Kunststoff nach oben zeigt.

    • Entferne mit einem T10 Torx-Schraubendreher die vier 8,6 mm Schrauben, mit denen die Festplatte an der Montagehalterung befestigt ist.

  22. Xbox One X Festplatte tauschen: Schritt 22, Bild 1 von 2 Xbox One X Festplatte tauschen: Schritt 22, Bild 2 von 2
    • Hebe die Halterung von der Festplatte ab.

  23. Xbox One X Festplatte tauschen, Stecker des Festplattenlaufwerks abziehen: Schritt 23, Bild 1 von 2 Xbox One X Festplatte tauschen, Stecker des Festplattenlaufwerks abziehen: Schritt 23, Bild 2 von 2
    • Ziehe den Festplattenanschluss von der Festplatte ab, indem du parallel zur Länge der Festplatte ziehst.

Abschluss

Um dein Gerät wieder zusammenzubauen, befolge diese Anweisungen in umgekehrter Reihenfolge.

Entsorge deinen Elektroschrott fachgerecht.

Die Reparatur hat nicht wie geplant geklappt? Versuche es mit einigen grundlegende Lösungsansätzen oder frage in unserem Xbox One X AForum nach.

99 weitere Nutzer:innen haben diese Anleitung absolviert.

Besonderer Dank geht an diese Übersetzer:innen:

en de

100%

Diese Übersetzer:innen helfen uns, die Welt zu reparieren! Wie kann ich mithelfen?
Hier starten ›

Kyle Smith

Mitglied seit: 02/01/21

40.630 Reputation

123 Anleitungen geschrieben

20 Kommentare

If I buy a new hard drive off of amazon, how do I install the Xbox OS back on? The offline usb?

SilentWorkForce - Antwort

The only way I found was to clone the disc sector-by-sector. I read online that you can expand it by making the “user content” partition larger.

Bryan Remely -

Do an offline update for xbox one x. I posted a link in another comment.

mike forrest -

Check out this video. It has a great step by step for putting the console into troubleshooting mode and downloading the correct software.

XBox One X SSD Upgrade - LFC#268 - YouTube

metric -

I read a post somewhere saying that if Microsoft detect non-standard hardware in your system you could be banned. Has anyone had any experience with this?

David Marques - Antwort

That was the case for the Xbox 360, these were very picky and only accepted certain models of Western Digital Hard Drives (if you didn't modify them with RGH/JTAG but then you would get banned if you tried to connect to Xbox Live).

The Xbox One is totally fine with other hard drives, I replaced my One X's HDD two years ago with a 2 TB Samsung 860 Evo SSD and had no problems, some people rather recommend using the SSD externally but IMHO it's worth the effort, because it also accelerates the Operating System drastically like in every PC/Mac (I don't want to use systems with the OS on an HDD anymore except some retro computers up to mid-2000s).

Marcel Pape -

I didn’t remove the fragile connectors, that ribbon cable I just opened the lock and slowly slid out the ribbon cable, I finally just put it all back together it took me a day, I done it very slowly, I have a SSD in there, it’s blazing fast. After doing all that download OSU1, extract it and format your USB to NTFS, copy $systemupdate to the root of your NTFS formatted USB, the update will auto partition and script the hard drive, download OSU1 from Microsoft, specifically search for offline Xbox update, then good luck putting your Xbox back together. No need to run third part scripts anymore.

King Difius - Antwort

I have had no luck finding the xbox one x os im not sure if its general for all xbox ones or if there’s a specific one for each? Also I’ve had not luck finding a source for a link to the code to reformat the drive that I trust (except for the ifixit youtube video but that link is dead.) in summary I was wondering if there is a good source someone could lead me to?

erik manousaridis - Antwort

This is the link for One X and One S models: https://support.xbox.com/en-US/help/hard...

The article says something about a different file for regular Xbox One. Idk what or where it is. But it’s on their site somewhere.

Andrew Sauk -

A couple of questions posted on installing the OS:

https://support.xbox.com/en-CA/help/hard...

*The download file is there too and you can see the link but you must right-click and save as. Regular left-click will not work.

mike forrest - Antwort

This was exactly right. New Hard drive in, the trouble shooter auto-ran when the xbox was turned on. I installed the update from a formatted Flashdrive and it’s all up and running.

(Running a 2018 Xbox One X)

Stuart Morris -

Good guide, thanks. There’s no need to unplug the sata cables from the main board, though, as there is enough play to reach the four screws holding the hdd to the plastic bracket.

Reinstalling the last part of the case can be tricky, the key is to locate the plastic lugs down one side of the base in their respective slots on the case. Once they’re in it all falls into place.

Mark Midderigh - Antwort

I purchased a 1 TB Samsung 870 QVO for my Xbox One X, I did not perform any formatting to the HDD prior to the install, it went straight from the packaging it came in and was installed in the console. I didn’t use any scripts or OSU files. I simply plugged the ethernet cable in and booted it up using the manual recovery button method. The Xbox immediately recognized the new SSD and automatically formatted and installed the OS. No special tools or hacks. The console is just like it was before just loads games a bit faster, I can play online, it updates when it needs to without hassle. Not sure why everyone is having such a hard time with finding so called software for the new hdd.

Stephen Sherfield - Antwort

I had to download the software to a usb drive and install it manually. Not sure how yours automatically installed the new software.

metric -

I like to use the Powershell script from XFiX on this YouTube channel to do hard drive maintenance (format, partition, etc.) on the XBox Hard Drive. He also has some other helpful videos too.


https://www.youtube.com/watch?v=3GlX_Ev_...

Scott - Antwort

Did you not read the last comment before yours? You don't need any of the formatting tools. Just stick the new drive in connect to the internet with Ethernet and when it boots up it will do all the work for you.

Stephen Sherfield -

Honestly I am desperate, I tried to change with another SSD for my Xbox One X Scorpio Edition, which the original HDD is dead.

I purchased Kingston 480GB and another one Crucial 1TB, they didn't work and didn't start. Xbox One X is very weird, it don't want another any kind of SSD/HDD! Anyone experienced same way? Thanks in advance

MikieL - Antwort

The drive I ordered wasn't anything too special.

Amazon.com: SanDisk SSD PLUS 1TB Internal SSD - SATA III 6 Gb/s, 2.5"/7mm, Up to 535 MB/s - SDSSDA-1T00-G26 : Electronics

I followed the guide here and then the OS restore here.

XBox One X SSD Upgrade - LFC#268 - YouTube

Worked like a charm.

metric -

As much as I would want a faster SSD on mine, I'm not doing this one, if there's a risk of getting banned.

Roger C. Rocha - Antwort

If I buy this hard drive do I need a thumb drive with the Xbox os on it?

Corey - Antwort

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 80

Letzte 7 Tage: 499

Letzte 30 Tage: 2,437

Insgesamt: 144,064