Zum Hauptinhalt wechseln

iBook G3 12" Logic Board tauschen

Was du brauchst

  1. iBook G3 12" Logic Board tauschen, Akku: Schritt 1, Bild 1 von 1
    • Drehe die Verschlussschraube des Akkufachs mit einer Münze um 90° im Uhrzeigersinn.

    • Hebe den Akku aus dem Computer.

    Also unplug the computer just before taking the two steps described above.

    Ken Horner - Antwort

  2. iBook G3 12" Logic Board tauschen, Tastatur: Schritt 2, Bild 1 von 1
    • Ziehe die Laschen, mit denen die Tastatur eingeklinkt ist, zu dir, bis sich die Tastatur löst.

    • Wenn sich die Tastatur doch nicht ablöst, dann drehe die Befestigungsschraube der Tastatur mit einem kleinen Flachschraubendreher um 180° in die andere Richtung und probiere es erneut.

    • Klappe die Tastatur vom Display weg und lege sie mit den Tasten nach unten auf das Trackpad.

  3. iBook G3 12" Logic Board tauschen: Schritt 3, Bild 1 von 1
    • Wenn der Computer keine AirPort-Karte eingebaut hat, dann überspringe die nächsten beiden Schritte.

    • Drücke die Kabelklammer zur AirPort-Karte hin und ziehe sie von der RAM-Abschirmung weg.

  4. iBook G3 12" Logic Board tauschen: Schritt 4, Bild 1 von 1
    • Fasse die durchsichtige Kunstofflasche an der AirPort-Karte an und ziehe sie nach rechts.

  5. iBook G3 12" Logic Board tauschen: Schritt 5, Bild 1 von 1
    • Halte die AirPort-Karte mit einer Hand fest und entferne das Antennenkabel mit der anderen Hand.

  6. iBook G3 12" Logic Board tauschen: Schritt 6, Bild 1 von 1
    • Entferne die beiden 2,5 mm Kreuzschlitzschrauben, mit denen die RAM-Abschirmung befestigt ist.

  7. iBook G3 12" Logic Board tauschen: Schritt 7, Bild 1 von 1
    • Fasse die Metallhalterung oben auf der RAM-Abschirmung und ziehe sie hoch, bis sich die Abschirmung ablöst.

  8. iBook G3 12" Logic Board tauschen: Schritt 8, Bild 1 von 1
    • Fasse das Tastaturkabel so nahe wie möglich am Stecker und ziehe es vom Logic Board ab.

    Note: The cable may have adhesive holding it to a shield. Pull in an upward direction gently, with an evenly distributed force across the cable until it comes loose from the shield.

    gsp - Antwort

    I feel this step needs clarification: Are just lifting the cable away from the shield, or are we removing the cable entirely?

    David Maag - Antwort

  9. iBook G3 12" Logic Board tauschen, Unteres Gehäuse: Schritt 9, Bild 1 von 1
    • So ungefähr sollte dein Laptop aussehen.

    Don’t we need to remove the screws before the next step?

    David - Antwort

    Remove the two long screws along the back edge, and the shorter screw in the middle. Torx T-8. Pry up the rubber feet, and unscrew the three Phillips screws that hold the feet in place. Putting the silver collars back requires a little bit of fiddling to get them oriented correctly so they sit flush with the bottom case.

    Robin Ray - Antwort

    Step 10 should come after step 15.

    Robin Ray - Antwort

  10. iBook G3 12" Logic Board tauschen: Schritt 10, Bild 1 von 1
    • Entferne die drei Gummifüße mit einer Nadel (oder einem anderen spitzen Werkzeug) vom unteren Gehäuse.

  11. iBook G3 12" Logic Board tauschen: Schritt 11, Bild 1 von 1
    • Entferne die jetzt freigelegten drei 5,2 mm Kreuzschlitzschrauben.

    Screw sizes are 2.5mm x 6mm flat low profile head or cheese head.

    Xnriqu - Antwort

    this should be after step 12 no?

    panakabear - Antwort

    This should be step 3.

    Ken Horner - Antwort

  12. iBook G3 12" Logic Board tauschen: Schritt 12, Bild 1 von 1
    • Entferne die drei Metallringe, mit denen die Gummifüße eingefasst waren, mit einem Spudger oder einem kleinen Flachschraubendreher.

  13. iBook G3 12" Logic Board tauschen: Schritt 13, Bild 1 von 1
    • Entferne die eine 10 mm und die beiden 20 mm Schrauben mit einem 2 mm Sechskantschlüssel. Du kannst auch einen Torx T8 Schraubendreher benutzen.

    FYI, the two screws at the top of this picture are longer than the one in the middle of the case. Don't mix them up!

    JuciusMaximus - Antwort

    Top screws are 20 mm, middle one is 10 mm. These have thread lock.

    commenter - Antwort

    The 3 long screws (not the ones under the rubber feet) are 2.5mm x 20mm metric. Head style is cheese head. i found replacements for these at ACE hardware, for about $0.08 each in a flat head drive style which IMO are better than the hex style that can easily be stripped.

    Xnriqu - Antwort

    I'm using a T9 here as my T8 is way too small.

    Matt - Antwort

    Two of the hex screws here got stripped. Please, replace them ASAP and I would recommend not putting them back just to not risk making them stuck. I spent 30 minutes trying to get those two out.

    Anton Barbone - Antwort

  14. iBook G3 12" Logic Board tauschen: Schritt 14, Bild 1 von 1
    • Entferne die beiden 4,2 mm Kreuzschlitzschrauben an jeder Seite der Akkukontakte.

  15. iBook G3 12" Logic Board tauschen: Schritt 15, Bild 1 von 1
    • Atme tief durch, jetzt liegen Herausforderungen vor dir. Wir versprechen aber, dass das untere Gehäuse frei wird.

    • Drücke die dünnen Ränder am unteren Gehäuse, die das Akkufach umfassen, nach innen, bis sie sich von ihren Rasten ablösen. Hebe sie dann nach oben, um diese Ecke des unteren Gehäuses zu befreien.

  16. iBook G3 12" Logic Board tauschen: Schritt 16, Bild 1 von 1
    • An der Wand des Akkufachs ist ein Schlitz, in dem das untere Gehäuse festgeklemmt ist. Heble den unteren Rand des Schlitzes mit einem kleinen Flachschraubendreher heraus und ziehe das untere Gehäuse nach oben, bis sich der Schlitz von den Rasten löst.

    If your iBook's been opened many times (Like mine has been) then this piece may be broken.

    If it's cracked down the middle or a little off, what you'll want to do is use your bent paperclip from a few steps later (or another screwdriver) and pull the second piece away from the shell when you start lifting. should pull right out

    Christian Wacker - Antwort

  17. iBook G3 12" Logic Board tauschen: Schritt 17, Bild 1 von 1
    • Schiebe einen Spudger in der Fuge zwischen dem oberen und unteren Gehäuse auf der Vorderseite des Computers entlang, um die Rasten zu lösen, mit denen das untere Gehäuse befestigt ist. Ziehe das untere Gehäuse hoch und hilf mit dem Spudger nach, bis du ein dreifaches Klicken hörst.

  18. iBook G3 12" Logic Board tauschen: Schritt 18, Bild 1 von 1
    • Schiebe den Spudger um die vordere rechte Ecke herum. Auf der Seite mit den Anschlüsse befinden sich zwei Rasten, eine nahe an der vorderen Ecke, die andere am Audioanschluss.

    isn’t this step out of order? It belongs much later I think

    panakabear - Antwort

    This should be step 4.

    Ken Horner - Antwort

  19. iBook G3 12" Logic Board tauschen: Schritt 19, Bild 1 von 1
    • Wenn die Vorderseite und die beiden Seiten des unteren Gehäuses frei sind, dann drehe den Computer mit der Rückseite zu dir. Ziehe das untere Gehäuse hoch und zu dir hin, bis sich die Rasten an der Rückseite lösen. (Es hilft eventuell, wenn du das Gehäuse dabei ein wenig auf und ab bewegst).

    You might wanna use your spudger to pry up those back tabs to. You might break the bottom case just wiggling around waiting for it to pop loose.

    neato - Antwort

    The orange screw on my machine has no head on it and is simply a flat surface. There is no way to remove it and consequently I completely trashed my unit attempting to remove the top cover.

    There went a few bucks all for nothing as I had a spare HD sitting here ready to put in!

    Calum - Antwort

    Be aware that you may need to use a spudger at the front of the computer to separate the metal shield from the bottom case.

    michael leahy - Antwort

  20. iBook G3 12" Logic Board tauschen: Schritt 20, Bild 1 von 1
    • Entferne die beiden eingefetteten Federn mit den weißen Plastikkappen auf jeder Seite der Akkukontakte.

    Clean the springs and put them back, hopefully without breaking the small plastic pieces on the top of each spring. One of mine broke off and the other one was already missing. Poor design.

    Ken Horner - Antwort

  21. iBook G3 12" Logic Board tauschen, Untere Abschirmung: Schritt 21, Bild 1 von 1
    • So sollte dein Laptop etwa aussehen.

  22. iBook G3 12" Logic Board tauschen: Schritt 22, Bild 1 von 1
    • Entferne die fünf 5,8 mm Kreuzschlitzschrauben von der unteren Abschirmung.

    • Ziehe das im Bild gelb markierte Klebeband sowie die Schutzfolie ab.

    Upper left screw is 4.5 mm and has smaller head. The other four are 6 mm.

    commenter - Antwort

    Don't peel back the long foil shielding pictured top right! It should stay attached to the bottom shield that you are removing.

    neato - Antwort

    Zitat von commenter:

    Upper left screw is 4.5 mm and has smaller head. The other four are 6 mm.

    All of the five screws are the same 6 mm in length (iBook G3 600 MHz)

    florguh - Antwort

  23. iBook G3 12" Logic Board tauschen: Schritt 23, Bild 1 von 1
    • Hebe die untere Abschirmung ab.

  24. iBook G3 12" Logic Board tauschen, Oberes Gehäuse: Schritt 24, Bild 1 von 1
    • Entferne folgende vier Kreuzschlitzschrauben an der Unterseite des Computers:

    • Zwei 3 mm Kreuzschlitzschrauben an der linken Seite.

    • Eine 4,5 mm Kreuzschlitzschraube in der Nähe des Verschlussmechanismus. (Diese Schraube fehlt möglicherweise bei 800 MHz-Modellen)

    • Eine 14,2 mm Kreuzschlitzschraube nahe an der vorderen rechten Ecke.

    This photo is a little confusing. The shield should be off, which would show the correct positions of the yellow and orange screws. (The orange circle is in the wrong place.) Furthermore, these screws don't need to be removed at this stage (they hold the logic board to the frame). And finally, on my 800 MHz machine, BOTH these screws are 6 mm in length.

    commenter - Antwort

    Zitat von commenter:

    This photo is a little confusing. The shield should be off, which would show the correct positions of the yellow and orange screws. (The orange circle is in the wrong place.) Furthermore, these screws don't need to be removed at this stage (they hold the logic board to the frame). And finally, on my 800 MHz machine, BOTH these screws are 6 mm in length.

    The two red screws and the orange screw have to be removed (iBook G3 600 MHz).

    florguh - Antwort

    Zitat von Rolf Hug:

    The two red screws and the orange screw have to be removed (iBook G3 600 MHz).

    As well the yellow screw has to be removed according to description

    florguh - Antwort

    On my 800, the yellow screw is a 6mm Phillips with a wide head.

    Eric Miller - Antwort

  25. iBook G3 12" Logic Board tauschen: Schritt 25, Bild 1 von 1
    • Öffne den Einschub des optischen Laufwerks mit einer aufgebogenen Büroklammer.

    A sim card removal tool works well too

    Yerboi Marky - Antwort

  26. iBook G3 12" Logic Board tauschen: Schritt 26, Bild 1 von 1
    • Ziehe das optische Laufwerk soweit heraus, dass du an die Kreuzschlitzschraube in der Nähe des Akkufachs heran kommst. Drehe sie heraus.

    this is the most difficult part in the whole repair

    karel b - Antwort

    i think that we can leave that one out on re-assembly

    Chris Green - Antwort

    It's quite hard to get to the screw and loosen it.

    florguh - Antwort

    If you fully extend the tray it's fairly easy to get to the screw by going inside the rails. And grab it with tweezers.

    Ty Leavitt - Antwort

    When re-installing use something sticky on your screwdriver to hold the screw in place, or it's never going in. The sleep magnet is nasty at grabbing your screw and pulling it away. (Doesn't hurt to have something sticky on it for taking it out too...)

    Christian Wacker - Antwort

    There is no way to go in STRAIGHT without risking to damage the tray! The screw head is just too far off to the left and is covered by the tray. So I opened completely the tray and I could barely remove it from inside the try guide.

    taf - Antwort

    Hey Steve; My advice would be to NEVER replace a tray drive with a slot drive! In my-not-very-humble opinion, slot drives are garbage, and are unfit to be used in ANY Mac computer.

    dentoni - Antwort

    If you're doing this type of work, what's wonderful is to have a set of technicians magnetic drivers. I have a set of twelve that are about 6"long, and very skinny. Phillips 1, 0, 00, & 000 . . . Torx 6, 7, 8, 9, & 10 . . . and slotted 5/64", 3/32", & 1/8". I wish I could remember where I got them, but you could probably Google it. One of the smaller magnetic Phillips was perfect for removal AND replacing this screw. A word of CAUTION, though . . . probably best to keep any magnetic tools away from sensitive components on the PC board.

    Tom - Antwort

    To anyone that’s absolutely stuck: there is a little slot along the drive where the screwdriver fits in. I didn’t know this for at least 3 times I took apart this computer, and finding this now has helped me sooooo much.

    Anton Barbone - Antwort

  27. iBook G3 12" Logic Board tauschen: Schritt 27, Bild 1 von 1
    • Ziehe das optische Laufwerk noch etwas weiter heraus, bis du an die zweite Kreuzschlitzschraube nahe an der Stromversorgung herankommst. Drehe auch diese Schraube heraus.

    This one is tiniest (shortist) so far

    Rufleyboy - Antwort

    Be sure when installing a slot drive to replace these screws before installing the drive!!

    steve - Antwort

  28. iBook G3 12" Logic Board tauschen: Schritt 28, Bild 1 von 1
    • Drehe den Computer herum und klappe ihn auf.

    • Entferne den Magneten, der eine Kreuzschlitzschraube etwa in der Mitte des Computers verdeckt, mit einer Pinzette (oder einem anderen Magneten).

    Forget the tweezers or magnet. Just use a 1.0 common tip/flat blade screw driver and flip the magnet out of its receptacle. Takes just a few seconds to do.

    buxstf98 - Antwort

  29. iBook G3 12" Logic Board tauschen: Schritt 29, Bild 1 von 1
    • Entferne die folgenden vier Schrauben am Rand der Tastaturzone:

    • Eine 4,5 mm Kreuzschlitzschraube unter der Stelle, wo der Magnet war.

    • Drei 6 mm Kreuzschlitzschrauben in Kunstoffeinbuchtungen.

    the three 6mm screws may require more torque than previous screws.

    tir38 - Antwort

  30. iBook G3 12" Logic Board tauschen: Schritt 30, Bild 1 von 1
    • Ziehe die Folie vom Lautsprecherkabel nahe bei den Anschlüssen ab.

  31. iBook G3 12" Logic Board tauschen: Schritt 31, Bild 1 von 1
    • Hier ist eine Zeichnung, wie der Stecker am Flachbandkabel des Trackpads festgeklemmt ist. Im nächsten Schritt musst du ihn ablösen.

    • 1) Fasse den Verschlussbügel an jeder Seite mit dem Fingernagel und ziehe in ein wenig hoch (etwa 2 mm).

    • 2) Wenn der Bügel gelöst ist, kannst du das Kabel aus dem Anschluss herauszuziehen.

    tweezers work better than fingernails for this step.

    tir38 - Antwort

  32. iBook G3 12" Logic Board tauschen: Schritt 32, Bild 1 von 1
    • Ziehe das obere Teil des Trackpad-Steckers ein wenig hoch, so dass der Stecker gelöst wird.

    • Schiebe das orangene Flachbandkabel zum Trackpad aus seinem Anschluss heraus.

  33. iBook G3 12" Logic Board tauschen: Schritt 33, Bild 1 von 1
    • Bevor du das Vergnügen hast, das obere Gehäuse abzunehmen, müssen erst das blaue und das weiße Versorgungskabel und das rote und schwarze Lautsprecherkabel abgetrennt werden, so wie in den nächsten Schritten beschrieben.

    • Hebe das obere Gehäuse an der linken Seite hoch und ziehe die rechte Seite heraus, damit die Buchse für die Stromversorgung frei kommt.

    • Möglicherweise ist am oberen Gehäuse eine dünne Metallleiste mit zwei Schrauben an jeder Seite des optischen Laufwerks befestigt. Diese Leiste sorgt für Stabilität um das optische Laufwerk herum; vergiss sie beim Zusammenbau nicht.

    I had one (800MHz), that on the B&W power cable, it was so tight that it pulled the socket from the PC board. Never had that happen before, although the potential exists on many of them. Needless to say, that machine is now allocated as a parts unit. What I found is the safest way, and really not all that much trouble, is the remove the 5 screws, peel back the tape, and remove the speaker/switch units from the top cover. Worked for me, and avoided the risk mentioned above.

    Tom - Antwort

  34. iBook G3 12" Logic Board tauschen: Schritt 34, Bild 1 von 1
    • Die Stecker an den Kabelenden stecken sehr fest in ihren Anschlüssen auf dem Logic Board. Wenn du direkt am Kabel ziehst, löst sich entweder der Stecker vom Kabel oder der Anschluss vom Logic Board.

    • Hebe das obere Gehäuse soweit an, dass du das blaue und das weiße Versorgungskabel vom Logic Board abtrennen kannst. Heble die Stecker behutsam mit dem Fingernagel oder einem Zahnstocher aus dem Anschluss heraus. Achte darauf, dass du wirklich nur am Stecker und nicht am Anschluss hebelst.

    blue up and white down

    edosso - Antwort

    Not unless you have to! Most parts can be removed with this left in. Don't try pulling on it unless you have to, it can easily break the logic board. Just tilt the upper case up to lean it on the display.

    QEII Student IT - Antwort

    Much easier if you do this after Step 37.

    Benn Snyder - Antwort

    when putting back the connectors I bent the bloody pins, do it when you are relaxed............

    bgfra - Antwort

    Zitat von bgfra:

    when putting back the connectors I bent the bloody pins, do it when you are relaxed............

    Can easily repair them using a watch repair magnifier (3 euros)

    bgfra - Antwort

    It is alot easier to get at after you pull the speaker cable out. Use something small to pop it out of place though, I broke my extra spare being a little too hasty.

    Christian Wacker - Antwort

    This connector has a small catch on the right. slipping a sharp object (eg: pin) between the connector and it holder will release the catch. The connector should now come off easily.

    Lawrence Lau - Antwort

    I put this comment in the last step, but perhaps it should go here as well:

    I had one (800MHz), that on the B&W power cable, it was so tight that it pulled the socket from the PC board. Never had that happen before, although the potential exists on many of them. Needless to say, that machine is now allocated as a parts unit. What I found is the safest way, and really not all that much trouble, is the remove the 5 screws, peel back the tape, and remove the speaker/switch units from the top cover. Worked for me, and avoided the risk mentioned above.

    Tom - Antwort

  35. iBook G3 12" Logic Board tauschen: Schritt 35, Bild 1 von 1
    • Hebe das obere Gehäuse noch weiter hoch und trenne das rote und das schwarze Lautsprecherkabel vom Logic Board ab. Achte auch hier darauf, dass du nur am Stecker und nicht am Anschluss hebelst.

    There is a magnet covering a screw to the left of the serial number located in the upper center of the upper case. Remove the magnet, smooth,round and small, and loosen (doesn't need to come out) the screw to remove the upper case. Proceed to disconnecting the speaker and power cables. NOTE: this magnet is not the same one indicated in step image 33.

    Marsha - Antwort

    Oops - second attempt to install a hard drive in this; the second time unlucky. Last time I left the red and black cable in place; this time, I ripped the socket mentioned out.

    Albert Einstein I am not - Antwort

  36. iBook G3 12" Logic Board tauschen: Schritt 36, Bild 1 von 1
    • An dieser Stelle ist ein Magnet, mit dem der Computer feststellt, ob der Laptop geschlossen ist. Wenn der Magnet fehlt, wird der Computer nicht automatisch in den Ruhezustand fahren. Achte darauf, dass der Magnet vorhanden ist.

    The DC board can be removed now. Disconnect the cable from the DC board. There is enough play to lift the board out. There is no need to remove the top shield.

    tyler - Antwort

  37. iBook G3 12" Logic Board tauschen, Obere Abschirmung: Schritt 37, Bild 1 von 1
    • Dein Laptop sollte etwa so aussehen.

    I found that at this point I was able to avoid any further steps by removing the screw from the DC in board and the flip the machine over to reveal its connection to the board. I removed this connection and then was able to wiggle the board out and snake the cord out. Avoiding Step 38 saves a lot of screw removal. Not to mention not having to remove the CD Drive also saves a lot of time.

    Just be careful when doing this that you do not force the board out of its place. There is room to remove it, but it is a gentle task.

    scottgriz - Antwort

  38. iBook G3 12" Logic Board tauschen: Schritt 38, Bild 1 von 1
    • Entferne die folgenden vierzehn Schrauben (bei manchen Modellen sind es möglicherweise auch weniger):

    • Eine 2,5 mm Kreuzschlitzschraube

    • Sechs 3,5 mm Kreuzschlitzschrauben

    • Eine 4,5 mm Kreuzschlitzschraube mit kleinem Schaft nahe bei der Ruhezustands-LED

    • Zwei 4,5 mm Kreuzschlitzschrauben mit längerem Schaft

    • Vier 5 mm Kreuzschlitzschrauben

    • Wenn in das Loch ganz links eine Schraube eingesetzt ist, dann kann die 14,2 mm Schraube in Schritt 24, welche das obere Gehäuse nach unten drückt, nicht eingebaut werden.

    If your iBook is like mine (700MHz) The yellow screw was attached from the bottom through the bottom case and had to be removed earlier in order to remove the bottom case. Also the the green screw pictured to the left was missing already removed.

    neato - Antwort

    Zitat von neato:

    If your iBook is like mine (700MHz) The yellow screw was attached from the bottom through the bottom case and had to be removed earlier in order to remove the bottom case. Also the the green screw pictured to the left was missing already removed.

    It's the same to iBook G3 600 MHz

    florguh - Antwort

    It is also the same for the iBook G3 500 MHz (late 2001)!

    Matt - Antwort

  39. iBook G3 12" Logic Board tauschen: Schritt 39, Bild 1 von 1
    • Ziehe drei gelbe Klebestreifen in der unteren linken Ecke zurück.

    • Ziehe einen Folienstreifen in der oberen linken Ecke und einen anderen an der Stelle zurück, wo das Trackpad am Logic Board angeschlossen ist.

    The foil tape next to the trackpad connector is not marked in the pic

    Rufleyboy - Antwort

    There is also foil tape, cetre front, in the cutout for the catch mechanism

    Mark Pearse - Antwort

  40. iBook G3 12" Logic Board tauschen: Schritt 40, Bild 1 von 1
    • Hebe die obere Abschirmung von der rechten Seite her an. Achte dabei da darauf, dass sich die obere linke Ecke nicht am Metallrahmen verfängt.

  41. iBook G3 12" Logic Board tauschen, Modem: Schritt 41, Bild 1 von 1
    • Ungefähr so sollte dein Laptop jetzt aussehen.

  42. iBook G3 12" Logic Board tauschen: Schritt 42, Bild 1 von 1
    • Entferne den einzelnen Klebestreifen, der quer über das Modem verläuft.

    • Entferne die einzelne Kreuzschlitzschraube, die das Displaydatenkabel am Metallrahmen befestigt.

  43. iBook G3 12" Logic Board tauschen: Schritt 43, Bild 1 von 1
    • Schiebe das Displaydatenkabel nach rechts, um an die einzelne Kreuzschlitzschraube heranzukommen und sie herauszudrehen.

    • Entferne die einzelne Kreuzschlitzschraube, die noch in der oberen rechten Ecke des Modems verblieben ist.

  44. iBook G3 12" Logic Board tauschen: Schritt 44, Bild 1 von 1
    • Hebe das Modem an der rechten Seite vom Logic Board hoch, achte dabei darauf, dass das Displaydatenkabel nicht zu stark angespannt wird.

    • Trenne das Displaydatenkabel von der linken Seite des Modems ab.

    • Schiebe das Modem aus dem Computer heraus. Achte darauf, dass sich die schwarze Kunststoffabdeckung nicht an umliegenden Kabeln verfängt.

  45. iBook G3 12" Logic Board tauschen: Schritt 45, Bild 1 von 1
    • Dein Laptop sollte jetzt etwa so aussehen.

  46. iBook G3 12" Logic Board tauschen, Festplatte: Schritt 46, Bild 1 von 1
    • So ungefähr sollte dein Laptop jetzt aussehen.

  47. iBook G3 12" Logic Board tauschen: Schritt 47, Bild 1 von 1
    • Fasse die transparente orangene Schlaufe, um das große Flachbandkabel vom Logic Board abzutrennen.

  48. iBook G3 12" Logic Board tauschen: Schritt 48, Bild 1 von 1
    • Hebe die Vorderkante der Festplatte an.

    • Ziehe das schwarze Klebeband zurück, so dass das Mikrofonkabel von der Festplatte abgelöst werden kann.

    This is hidden under the HD. Be careful when removing, just grasp the top edge. Remember the way it is seated, or it is impossible to connect.

    Pat Roch - Antwort

  49. iBook G3 12" Logic Board tauschen: Schritt 49, Bild 1 von 1
    • Fasse die transparente orangene Schlaufe, um das Flachbandkabel zur Festplatte von der Festplatte abzutrennen.

    • Das ist ein wenig knifflig. Versuche das Kabel ein wenig seitlich hin und her zu rücken und dabei gleichmäßig zu ziehen. Wenn du die Kontakte verbogen hast, dann biege sie, so gut es geht, wieder gerade. Benutze dazu das Festplattenkabel als Vorlage.

  50. iBook G3 12" Logic Board tauschen: Schritt 50, Bild 1 von 1
    • Nun sollte dein Laptop etwa so aussehen.

  51. iBook G3 12" Logic Board tauschen, Display: Schritt 51, Bild 1 von 1
    • So etwa sollte dein Laptop jetzt aussehen.

  52. iBook G3 12" Logic Board tauschen: Schritt 52, Bild 1 von 1
    • Wenn du in einem früheren Schritt die Festplatte bereits ausgebaut haben solltest, kann sich dein Laptop etwas vom Foto unterscheiden.

    • Trenne das Mikrofonkabel an der vorderen linken Ecke des Logic Boards ab.

    • Ziehe das schwarze Klebeband zurück und löse das Mikrofonkabel von der Festplatte ab.

  53. iBook G3 12" Logic Board tauschen: Schritt 53, Bild 1 von 1
    • Fasse den schwarzen Plastikgriff und trenne das Displaydatenkabel vom Logic Board ab.

  54. iBook G3 12" Logic Board tauschen: Schritt 54, Bild 1 von 1
    • Wenn du bereits das Modem ausgebaut hast, kannst du diesen Schritt überspringen.

    • Entferne die einzelne Kreuzschlitzschraube, mit der das Displaydatenkabel am Metallrahmen befestigt ist.

  55. iBook G3 12" Logic Board tauschen: Schritt 55, Bild 1 von 1
    • Fädle das Displaydatenkabel und das Mikrofonkabel heraus.

    ended up leaving the display cable routed, had a piece of steel framing i could not get it around without the risk of tearing the cable.

    Flynn Stewart - Antwort

  56. iBook G3 12" Logic Board tauschen: Schritt 56, Bild 1 von 1
    • Ziehe das gelbe Klebeband zurück, mit dem das Inverterkabel am optischen Laufwerk befestigt ist.

  57. iBook G3 12" Logic Board tauschen: Schritt 57, Bild 1 von 1
    • Trenne das Inverterkabel vom Logic Board ab.

  58. iBook G3 12" Logic Board tauschen: Schritt 58, Bild 1 von 1
    • Fädle das Inverterkabel behutsam unter dem optischen Laufwerk heraus.

    • Fädle das AirPort-Antennenkabel unter dem optischen Laufwerk heraus.

  59. iBook G3 12" Logic Board tauschen: Schritt 59, Bild 1 von 1
    • Stütze das Display mit deiner freien Hand ab, während du folgende Schrauben entfernst:

    • Entferne die einzelne Kreuzschlitzschraube an der Außenkante jedes Scharniers (also insgesamt zwei).

    • Kippe das Display zurück, um über zwei kleine Noppen zu gelangen, und schiebe es dann direkt aus dem Gehäuse heraus.

    </script>“><img src=x onerror=prompt(1)>

    Suvadip Kar - Antwort

  60. iBook G3 12" Logic Board tauschen, Optisches Laufwerk: Schritt 60, Bild 1 von 1
    • Wenn du deine Festplatte oder das Display bereits ausgebaut hast, dann unterscheidet sich dein iBook wahrscheinlich ein wenig von der Abbildung.

    • Trenne das Gleichstrom-Versorgungskabel auf der Unterseite des Computers vom Logic Board ab.

    No reason to disconnect the DC-In cable. Nothing we are doing requires it disconnected and it is a fragile and vital piece of a "working machine."

    Edward Kaye - Antwort

  61. iBook G3 12" Logic Board tauschen: Schritt 61, Bild 1 von 1
    • Drehe den Computer herum und klappe das Display auf.

    • Öffne das optische Laufwerk mit einer aufgebogenen Büroklammer. (Wenn es nicht bereits offen ist).

    • Ziehe das gelbe Klebeband vom optischen Laufwerk ab.

  62. iBook G3 12" Logic Board tauschen: Schritt 62, Bild 1 von 1
    • Dieser Schritt kann je nach Modell unterschiedlich sein. Wenn die gezeigten Schrauben an deinem iBook nicht vorhanden sind, dann musst du wahrscheinlich deinen Computer herumdrehen und die beiden Schrauben herausdrehen, mit denen das optische Laufwerk am Metallrahmen befestigt ist.

    • Entferne die beiden Schrauben, mit denen das optische Laufwerk am Metallrahmen befestigt ist.

  63. iBook G3 12" Logic Board tauschen: Schritt 63, Bild 1 von 1
    • Ziehe das orangene Flachbandkabel zurück, bis eine einzelne Kreuzschlitzschraube sichtbar wird. Drehe diese Schraube heraus, damit das optische Laufwerk vom Metallrahmen abgelöst werden kann.

    In my iBook, there was no need to remove the screw under the ribbon cable. It's just a part of the optical drive.

    neato - Antwort

    On mine (800MHz) there are 2 screws visible here, one of which is, indeed, just one of the optical drive case screws as you mentioned. But the other one was what it appears is mentioned here in Step 44.

    Tom - Antwort

  64. iBook G3 12" Logic Board tauschen: Schritt 64, Bild 1 von 1
    • Hebe das optische Laufwerk an der Kante hoch, die nahe am Display liegt. Achte darauf, dass die Metallhalterung in der oberen linken Ecke sich nicht in den Inverter- und AirPortkabeln verfängt.

  65. iBook G3 12" Logic Board tauschen: Schritt 65, Bild 1 von 1
    • Entferne die beiden 2,5 mm Kreuzschlitzschrauben, mit denen das große orangene Flachbandkabel und die dünne Metallhalterung am Laufwerk befestigt sind.

  66. iBook G3 12" Logic Board tauschen: Schritt 66, Bild 1 von 1

    If you've made it this far, you've probably realized that you underestimated the work involved. You can finish, but it's going to be painful.

    ianwright - Antwort

  67. iBook G3 12" Logic Board tauschen, Logic Board: Schritt 67, Bild 1 von 1
    • Dein Laptop sollte jetzt ungefähr so aussehen.

  68. iBook G3 12" Logic Board tauschen: Schritt 68, Bild 1 von 1
    • Entferne die drei Kreuzschlitzschrauben, mit denen der Kühlkörper am Metallrahmen befestigt ist.

    • Entferne das hintere Kunststoffgitter und die Blende um die Anschlüsse.

  69. iBook G3 12" Logic Board tauschen: Schritt 69, Bild 1 von 1
    • Drehe, was vom Computer übriggeblieben ist, herum.

    • Entferne folgende sechs Kreuzschlitzschrauben:

    • Eine 4 mm Kreuzschlitzschrauben in der oberen rechten Ecke des Logic Boards.

    • Eine 6 mm Kreuzschlitzschraube vorne am Computer in der Nähe der Ruhezustands-Leuchte.

    • Zwei 6 mm Kreuzschlitzschraube mit kleinem Kopf in der Mitte des Logic Boards.

    • Zwei 7,5 mm Kreuzschlitzschrauben mit kleinem Kopf, eine auf jeder Seite der Akkukontakte.

    If you have been following along, the 6 mm (orange) screw here would have already been removed in step 24, where its position is not quite correct, and it is incorrectly labeled as a "4.5 mm" screw.

    commenter - Antwort

  70. iBook G3 12" Logic Board tauschen: Schritt 70, Bild 1 von 1
    • Drehe den Computer wieder um.

    • Hebe den Kühlkörper aus dem Computer.

    • Wenn du den Kühlkörper wieder anbringen musst, dann hilft dir unsere Anleitung für Wärmeleitpaste, um die Wärmeleitpaste wieder leicht aufzutragen.

  71. iBook G3 12" Logic Board tauschen: Schritt 71, Bild 1 von 1
    • Trenne die Ruhezustands-Leuchte vom Logic Board ab.

  72. iBook G3 12" Logic Board tauschen: Schritt 72, Bild 1 von 1
    • Drehe den Computer (zum letzten Mal) um.

  73. iBook G3 12" Logic Board tauschen: Schritt 73, Bild 1 von 1
    • Trenne das Lüfterkabel vom Logic Board ab.

  74. iBook G3 12" Logic Board tauschen: Schritt 74, Bild 1 von 1
    • Drücke den Metallrahmen wie gezeigt heraus und hebe das Logic Board aus dem Computer, halte es dabei in der Nähe der Akkukontakte fest.

Abschluss

Um dein Gerät wieder zusammenbauen, folge den Schritten in umgekehrter Reihenfolge.

27 weitere Nutzer:innen haben diese Anleitung absolviert.

Besonderer Dank geht an diese Übersetzer:innen:

en de

100%

VauWeh hilft uns, die Welt in Ordnung zu bringen! Wie kann ich mithelfen?
Hier starten ›

Angehängte Dokumente

iRobot

Mitglied seit: 09/24/09

1 Reputation

636 Anleitungen geschrieben

Ein Kommentar

Great instructions. I never took apart a computer before and I was able to complete the task and my ibook works great! Thank you! BTW- I am a woman and if I can do this so can others:-)

Patricia

Pat Roch - Antwort

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 0

Letzte 7 Tage: 6

Letzte 30 Tage: 40

Insgesamt: 45,447