Einleitung

iSight not working? Replace your camera board.

  1. Before you work on the computer, unplug the computer and press the power button for 20-30 seconds to drain the stored energy in the power supply.
    • Before you work on the computer, unplug the computer and press the power button for 20-30 seconds to drain the stored energy in the power supply.

    • Loosen the two Phillips screws securing the access door to your iMac.

    • These screws are captive in the access door.

    Kommentar hinzufügen

  2. Remove the access door from your iMac.
    • Remove the access door from your iMac.

    Kommentar hinzufügen

    • Remove the three T8 Torx screws securing the front bezel to the rear panel.

    Kommentar hinzufügen

    • Orient the iMac face-up, on its backside.

    • Use your thumbs to press both RAM arms in past the front bezel for enough clearance to lift it off the rear case.

    Kommentar hinzufügen

  3. Frohes Fest, frohes Tüfteln
    Pack's ein, pack's aus, pack's an: Erhalte 12 € Rabatt auf deinen Einkauf ab 50 € mit dem Code FIXMAS12
    Frohes Fest, frohes Tüfteln
    Pack's ein, pack's aus, pack's an: Erhalte 12 € Rabatt auf deinen Einkauf ab 50 € mit dem Code FIXMAS12
    • While holding the RAM arms in with your thumbs, lift the lower edge of the front bezel enough to clear the rear case.

    Kommentar hinzufügen

    • Re-orient your iMac so it sits upright on the stand.

    • Insert a plastic card up into the corner of the air vent slot at the top of the rear case.

    • Push the card toward the top of the iMac to release the front bezel latch.

    • Pull the front bezel away from the rear case.

    • Repeat this process for the other side of the front bezel.

    • It may be necessary to apply several layers of duct tape to the top of the access card to aid in releasing the latches.

    • If the bezel refuses to release, try pressing the lower edge back onto the rear case and repeat this opening process.

    Using a strongish magnet will grab and release the latches.

    darkstar448 - Antwort

    Zitat von darkstar448:

    Using a strongish magnet will grab and release the latches.

    Are you sure it's safe to do this? How close is the hard drive, won't magnets interfere with it?

    Sarah - Antwort

    It's almost certainly fine. Modern hard drives are very resistant to magnetic fields.

    zschroeder6212 -

    • Lay your iMac stand-side down on a table.

    • Lift the front bezel from its lower edge and rotate it away from the rest of your iMac, minding the RAM arms that may get caught.

    • Lay the front bezel above the rest of the iMac.

    Kommentar hinzufügen

    • If necessary, remove the piece of kapton tape wrapped around the microphone and camera cables.

    Kommentar hinzufügen

    • Disconnect both the camera and microphone cables.

    Kommentar hinzufügen

    • Lay the bezel front side down on a table.

    • If necessary, peel back the tape covering the camera board.

    Kommentar hinzufügen

    • Remove the two T6 Torx screws securing the camera board to the front bezel.

    Kommentar hinzufügen

    • Lift the camera board out from the front bezel.

    Kommentar hinzufügen

Abschluss

To reassemble your device, follow these instructions in reverse order.

Kommentar hinzufügen

Statistik anzeigen:

Letzte 24 Stunden: 0

Letzte 7 Tage: 0

Letzte 30 Tage: 3

Insgesamt: 4,626