iMac Intel 21.5" EMC 2389 Festplatte austauschen

Einleitung

Interne Voraussetzung

Was du brauchst

Schritt 1 Festplatte

iMac Intel 21.5" EMC 2389 Festplatte austauschen, Festplatte: Schritt 1, Bild 1 von 2

iMac Intel 21.5" EMC 2389 Festplatte austauschen, Festplatte: Schritt 1, Bild 2 von 2

Ziehe den Stecker des Temperatursensors der Festplatte in Richtung Oberkante des iMac und löse ihn vom Sockel auf dem Logic Board.

Übersetzen

I don't think this is necessary, I'd just leave it since you're removing the other end from the drive.

maccentric - 13. Dez 2013 Antwort

Want to add a comment on this w/reference to HDD & thermal sensor. HDD used: WD1002FAEX - 1TB WD Black. Temperature sensor on this model iMac has a little tab/plastic protrusion, Apple HDD actually has specific opening for it. With this HDD/any after market WD HDD you should use small electrical wire cutters, and just cut off the offending piece of plastic from the iMac sensor. Insert it as specified, closest to SATA/PCB board, take a picture first before taking it out, and it works like a champ!

MaximBorzov - 22. Aug 2014 Antwort

Sure enough, I had the same problem of the temperature sensor not fitting because of the plastic protrusion on the Apple connector. Instead of using a wire cutter to remove the protrusion, I filed it with a metal file (careful to place a rag cloth underneath, where all the filing dust would drop). It fit wonderfully after that.

girlscandotoo - 10. Nov 2014

I am getting ready to swap out my wife's drive for an SSD. Since there are no moving parts do i need to be concerned with the temperature sensor?

I picked up a 240GB PNY CS1200 Series drive. Its smaller than the original but she doesnt use that much anyways.

Robert Hancock - 3. Aug 2015 Antwort

Schritt 2

Entferne die beiden 9 mm Torx T10 Schrauben, die die obere Halteklammer der Festplatte am Gehäuse befestigen.

Übersetzen

T8 screw on my Mid-2010.

rch - 14. Aug 2018 Antwort

Schritt 3

Drehe die Festplatte aus dem Gehäuse und hebe sie aus den Haltestiften in Richtung Oberkante des iMac.
Achte darauf, dass du dabei nicht die AirPort Karte berührst.

Übersetzen

Instead of trying to not hit the Airport card, spend 10 seconds to unscrew the one screw, pull it out of the socket and set it aside.

maccentric - 13. Dez 2013 Antwort

WATCH IT! When pulling out the hard drive or putting in the new one, stay clear of the strong magnets that hold the glass pane in place. I was so focused on following those steps closely, and when I had the HDD clear I kind of relaxed a bit too much and – "CLONK" – the magnet pulled the HDD and ruined it.

Roberting - 16. Nov 2014 Antwort

I have fitted a barracuda tb sata hdd ,i have partitioned the drive in d/utility .I have made a bootable us. stick containing os x and it says mac osx cannot be installed to your computer , even though itis displYed as verified in disk utility .......Plese help me !!!!!!

therumourcastro - 5. Feb 2015 Antwort

Schritt 4

Löse das SATA Datenkabel und die SATA Versorgung, indem du die jeweiligen Stecker von der Festplatte abziehst.

Übersetzen

Computer doesn’t see the new hard drive. Mid year 2010 iMac, #2389. Removed Seagate Barracuda 7200 500 gig drive. Installed Toshiba 7200, 1tb drive. Computer starts, screen lights but I get a ?. So I started in recovery mode but it doesn’t see a hard drive to load to. I have an external backup and it dies see that drive. Tried reinstalling the os over the internet but when it looks for a hard drive it doesn’t see one. The fan is running…starts off slowly but as timne goes by it gradyally speeds up.

Any help is apprecioated

Paul Theriault - 23. Dez 2017 Antwort