Zum Hauptinhalt wechseln

iMac Intel 21,5" EMC 2805 Festplatte austauschen

Was du brauchst

  1. iMac Intel 21,5" EMC 2805 Festplatte austauschen, Displayeinheit: Schritt 1, Bild 1 von 1
    In diesem Schritt verwendetes Werkzeug:
    iMac Intel 21.5" Cardboard Service Wedge
    $4.99
    Kaufen
    • Mit einem frei beweglichen Gelenk kann der iMac unkontrolliert pendeln, das macht es schwer an ihm zu arbeiten. Es geht leichter mit einem iMac Service Keil, es kann aber auch ohne ihn durchgeführt werden.

    • Wenn du die iFixit-Reparaturhilfe aus Karton verwendest, dann baue sie zuerst mit Hilfe dieser Anleitung zusammen.

    • Bevor du beginnst an deinem iMac zu arbeiten: Ziehe den Netzstecker, drücke und halte den Ausschaltknopf für mindestens zehn Sekunden. Dadurch werden die Kondensatoren im Netzteil entladen.

    • Sei sehr vorsichtig und berühre nicht die Leitungen oder Lötstellen an den Kondensatoren auf der Rückseite der Platine des Netzteils. Fasse diese nur an den Kanten an.

    The wedge is an extremely tight fit for this model. I was worried that the amount of force needed to use it as shown might damage the stand, so I used it with the long side down instead. It worked fine that way and didn’t need anywhere near as much force to insert.

    roberttrevellyan - Antwort

    Here’s a good YouTube vid on upgrading the RAM: Can a Normal Person Upgrade the RAM in the 2017 21.5" iMac?

    Dan - Antwort

    Here are a couple tips from me:

    1) Expose the adhesive to extreme temperatures. I did this by transporting my iMac in my car, screen-down on a piece of cardboard on a cold February morning (in Chicago). When I went to pick up the iMac, the screen practically fell off the chassis. I would have been distraught by this if I hadn’t already planned this replacement. So it was a happy accident.

    2) Remember to expell the residual power from the power supply by pushing the power button while the iMac is unplugged. This does NOT guarantee it’s safe to touch, but when I accidentally brushed the solder and exposed capacitors, I didn’t get shocked.

    jerrid_foiles - Antwort

    Instead of using the wedge, I placed the iMac faced up with the top side (web cam) facing me while I ran the pizza roller around. It worked out great!

    Sam Fung - Antwort

    “All iMacs also come with a traditional hard drive” mine doesn’t!! it’s HDD bay is completely empty, no SATA cable or anything. I guess I’ll have to upgrade the PCIe SSD instead.

    Chris Hughes - Antwort

    There is no replacement glass for this model, it is part of the LCD and impossible to remove or replace- the entire LCD has to be replaced unfortunately if the glass is cracked or damaged. You will have to Google search for a replacement. Also be careful with some of the lock tight tork screws as I broke one of my screw mounts taking one out.

    Phil Tesone - Antwort

    I used this service wedge but also found it a very tight fit. The same stabilization can be achieved by using a big rolled up towel.

    Ernst - Antwort

    While this is a good instruction guide, I recommend to also look at OWC’s instruction video about drive installation, before starting the exercise. Those install videos are very detailed and useful.

    Ernst - Antwort

    Main advice: TAKE YOUR TIME with the pizza roller.

    Make several passes, until you really feel like there's no more sticker in the way. Stay away from the camera though (approx. 1inch / 2.5cm on both sides). This will reduce the work left with the plastic card. Adhesive is really on the edge of the screen so there is absolutely no need to go any further than the recommended 1cm / 3/8inch depth.

    Where are the sensitive parts?

    Facing your iMac, imagine you're looking at a watch. There are antennas on 1, 2 and 4 o'clock. Do not insert any metal piece there (nor anywhere else, btw). Other than that AND the screen cables underneath the camera, not much danger.

    Froggy Manny - Antwort

  2. iMac Intel 21,5" EMC 2805 Festplatte austauschen: Schritt 2, Bild 1 von 2 iMac Intel 21,5" EMC 2805 Festplatte austauschen: Schritt 2, Bild 2 von 2
    • Setze das iMac Opening Tool an der linken Seite des Displays, in der Nähe des An/Aus Schalters beginnend, in die Spalte zwischen Glaspanel und Rückgehäuse ein.

    • Die Achse am iMac Opening Tool verhindert, dass du es zu tief einschieben kannst. Wenn du ein anderes Werkzeug verwendest, musst du aufpassen, dass du es nicht tiefer als 9 mm in das Display einschiebst.Sonst riskierst du ein Durchschneiden der Antennenkabel, was zu ernsthaften Schaden führen kann.

    Don’t get too worried about starting exactly where the picture says. The glue is stronger in some parts so just start wherever is easier and then work slowly and patiently around in the direction shown.

    Richard Cook - Antwort

    As this guide doesn’t cover replacing the adhesive strips, I found referring to the following was useful (noting that it’s not for the same model of iMac, so the modification they mention wasn’t necessary): IMac Intel 21.5 "EMC 2544 Klebestreifen ersetzen

    Alan Digby - Antwort

    It is very easy to crack the glass in front of the LCD during this step. I used the guitar pick, maybe it was too thick… crack is just on the frame but anyway it is disappointing :(

    Nikolay - Antwort

    This part of the exercise should be done with extreme patience. I took my sweet time with the opening tool, rolling it through the entire panel and enclosure gap over and over again, until I was very sure no parts were sticking together anymore. And when I thought I was I done, I decided to do it over again.

    Ernst - Antwort

    You can "warm up" the adhesive before try to cut it with the tool using a hair dryer. Heat the edges for about a minute, keep moving it so you don't cause stress in the glass. Also the above note.. use the tool and then the cards. Do not use a guitar pick or other objects as the thickness will cause you to break the front glass, which is a bonded part of the display (expensive).

    Carl Schultz - Antwort

    Merci pour ce conseil

    bry nicolas -

  3. iMac Intel 21,5" EMC 2805 Festplatte austauschen: Schritt 3, Bild 1 von 3 iMac Intel 21,5" EMC 2805 Festplatte austauschen: Schritt 3, Bild 2 von 3 iMac Intel 21,5" EMC 2805 Festplatte austauschen: Schritt 3, Bild 3 von 3
    • Benutze es wie einen Pizzaschneider - Rolle es entlang des Spalts und trenne dabei den Klebeschaum in der Mitte.

    • Achte darauf, dass du es immer mit dem Handgriff hinter dem Schneidrad führst. Wenn du ziehst, kann sich das Rad aus dem Griff lösen.

    • Lasse das Werkzeug die linke Seite des Displays entlang laufen.

    Erreur de traduction: "de bas en haut" et non de" haut en bas" sur le côté gauche de l'écran

    Moreau - Antwort

    If re-opening a screen that was opened and re-attached using iFixit’s adhesive strips, I would strongly recommend heating it first with an iOpener, heat gun or hair dryer. 20 minutes after attaching with the iFixit adhesive I tried to open it again with the pizza slicer to fix something and cracked the screen on the left-hand side.

    plasticpool - Antwort

  4. iMac Intel 21,5" EMC 2805 Festplatte austauschen: Schritt 4, Bild 1 von 3 iMac Intel 21,5" EMC 2805 Festplatte austauschen: Schritt 4, Bild 2 von 3 iMac Intel 21,5" EMC 2805 Festplatte austauschen: Schritt 4, Bild 3 von 3
    • Fahre fort und lasse das Werkzeug um die obere linke Ecke laufen.

    Ne pincez pas l’écran avec l’autre main. Vous exercez une pression inutile sur le verre et empêchez la roulette de couper le joint.

    phfoglia - Antwort

  5. iMac Intel 21,5" EMC 2805 Festplatte austauschen: Schritt 5, Bild 1 von 2 iMac Intel 21,5" EMC 2805 Festplatte austauschen: Schritt 5, Bild 2 von 2
    • Schneide die Klebeverbindung entlang der oberen linken Seite des Displays auf.

  6. iMac Intel 21,5" EMC 2805 Festplatte austauschen: Schritt 6, Bild 1 von 2 iMac Intel 21,5" EMC 2805 Festplatte austauschen: Schritt 6, Bild 2 von 2
    • Fahre an der Oberseite des Displays fort.

    • Du kannst das Werkzeug mehrmals hin und her schieben. So trennst du so viel wie möglich von der Klebeverbindung auf.

    In this step can I cut along the display without make any damage to the front camera?

    arisnordico - Antwort

    Hi! Actually - there is no need to cut the tape around the camera area - there is no tape to cut at all! And so, the way go is easy - just pass 10 mm to the left and to the right from camera and start cutting!

    P.S. Just did the whole procedure to replace a RAM and to add SSD on PSIe an hour ago! Seems to be different reading the instructions... you know - 2/10 and so on. But it's really not that hard, trust me. I'll give it 5/10.

    P.P.S. By the way there is one trick to pass the difficult steps. Any action which requires pulling smth (motherboard, speaker, power supply unit) from the narrow crack (or should i say - slit?) at the bottom of your Imac is really not so easy.

    And the trick is to first remove a thin metal stripe with some kind of insulation on it which held by 5 small (very small!!) screws at the bottom of your Imac. After you done it - it's easy to pull everything! Pay attention to the fact that one of this 5 screws at the center are more shortly than others.

    dv1977 - Antwort

    I did all steps like this manuell but now the Display wont work only some colered strips are to see! Whats happend??

    Can anybody help me ? Maybe the connector cable is broken?

    djfanta - Antwort

    Check both connectors, probably one of them not seated well

    pzhivulin -

    You can add a SATA SSD if you already have a PCIe SSD Factory?

    kaserlik - Antwort

    If you're changing cracked EMC 2638 display to new assembly, there's two more steps:

    Step 24: Use the tip of a spudger to flip up the metal retaining bracket on the display data cable.

    Carefully pull the display data cable from its socket on the display assembly.

    Step 25: Use the tip of a spudger to unplug bracket of the thermal sensor small cable near display data cable.

    Carefully remove scotch tape covering thermal sensor. Using iSesamo or flat tip of the spudger carefully peel the thermal sensor away.

    pzhivulin - Antwort

    omg - forgot to switch the termal sensor from the old display...

    now fan runs like crazy...

    Andrei Balotescu -

    The key thing is to never put any force on the opening tool when working through the tape. Just roll it back and forth with ease.

    Ernst - Antwort

  7. iMac Intel 21,5" EMC 2805 Festplatte austauschen: Schritt 7, Bild 1 von 3 iMac Intel 21,5" EMC 2805 Festplatte austauschen: Schritt 7, Bild 2 von 3 iMac Intel 21,5" EMC 2805 Festplatte austauschen: Schritt 7, Bild 3 von 3
    • Schiebe das Werkzeug um die obere rechte Ecke des Displays.

  8. iMac Intel 21,5" EMC 2805 Festplatte austauschen: Schritt 8, Bild 1 von 2 iMac Intel 21,5" EMC 2805 Festplatte austauschen: Schritt 8, Bild 2 von 2
    • Rolle das Werkzeug die rechte Seite des Displays nach unten.

  9. iMac Intel 21,5" EMC 2805 Festplatte austauschen: Schritt 9, Bild 1 von 2 iMac Intel 21,5" EMC 2805 Festplatte austauschen: Schritt 9, Bild 2 von 2
    • Beende das Schneiden mit dem iMac Opening Tool unten auf der rechten Seite des Displays.

    • An dieser Stelle solltest du noch einmal das Werkzeug um das ganze Display laufen lassen, um wirklich soviel von der Klebeverbindung wie möglich aufzutrennen.

    Yes, do it many times to loosen the adhesive.

    Noah Ralston - Antwort

    Would be good data to show the 3 areas (wifi antennas where the "tape" is larger and covers them. The rest of the "tape" is 1.4" and easy. Also after removing the display, be sure to remove the old "tape" from both the display and the rubber parts of the case. Use the spudger to start an end and it should pull off easily. Careful on the baackside of the display as you can scratch off the black paint/covering.

    Carl Schultz - Antwort

  10. iMac Intel 21,5" EMC 2805 Festplatte austauschen: Schritt 10, Bild 1 von 3 iMac Intel 21,5" EMC 2805 Festplatte austauschen: Schritt 10, Bild 2 von 3 iMac Intel 21,5" EMC 2805 Festplatte austauschen: Schritt 10, Bild 3 von 3
    In diesem Schritt verwendetes Werkzeug:
    Plastic Cards
    $2.99
    Kaufen
    • Das Werkzeug hat den größten Teil der Klebeverbindung aufgeschnitten., aber das Display ist immer noch ein wenig mit dem Gehäuse verklebt. Den letzten Rest musst du mit einer Plastikkarte lösen.

    • Lege den iMac mit der Scheibe nach oben auf den Tisch.

    • Beginne in der oberen rechten Ecke und zwänge eine Kunststoffkarte zwischen Display und Rahmen.

    • Achte darauf, die Karte nicht tiefer als 9 mm einzuschieben. Du könntest sonst Bauteile im Inneren beschädigen.

    this step is extremely important NOT to stick in the cards too far….. doing so, you risk a 600 euro replacement as I experienced………

    Edgar Broekema - Antwort

    I drew a 3/8” line on my cards with a marker first.

    Max Romano - Antwort

    I’m reading this on the EU store, please change all measurements to cm/mm.

    Morgana Devina - Antwort

    @ifixit The next batch of cards you create should have a line printed on the card 3/8” in from the edges. Would make a nice reference.

    Richard Giratd - Antwort

    Here’s where OWC provides glass removal suction cups, which is a better solution than plastic cards.

    The suction cups help to easily lift the glass panel, without risking the damaging of any internal wiring that the plastic cards could cause.

    Ernst - Antwort

    Better to remove stand wedge at this point? Can’t see from pics

    derekrobinson - Antwort

  11. iMac Intel 21,5" EMC 2805 Festplatte austauschen: Schritt 11, Bild 1 von 2 iMac Intel 21,5" EMC 2805 Festplatte austauschen: Schritt 11, Bild 2 von 2
    • Verdrehe die Plastikkarte seitlich und vergrößere so den Spalt zwischen Display und Rahmen.

    • Bewege die Karte vorsichtig und langsam, damit das Displayglas nicht zu stark belastet wird - du brauchst nur einen Spalt von etwa 6 mm Breite zu öffnen.

    This part must be done very carefully or you can damage the flat cable from display, despite it was under a iron cover.

    Cassio Machado - Antwort

  12. iMac Intel 21,5" EMC 2805 Festplatte austauschen: Schritt 12, Bild 1 von 3 iMac Intel 21,5" EMC 2805 Festplatte austauschen: Schritt 12, Bild 2 von 3 iMac Intel 21,5" EMC 2805 Festplatte austauschen: Schritt 12, Bild 3 von 3
    • Schiebe die Karte zur Mitte des Displays hin und schneide so allen Kleber an der rechten oberen Ecke des iMac auf.

    • Halte unbedingt vor der iSight Kamera an, damit sie nicht beschädigt wird.

    You don't need to do it like this, simply open the iMac bendidng the LCD completely and use the pizza cutter to remove the adhesive.

    Felix - Antwort

    Using glass removal suction cups will avoid running this risk of damaging the camera (or any wiring).

    Ernst - Antwort

  13. iMac Intel 21,5" EMC 2805 Festplatte austauschen: Schritt 13, Bild 1 von 2 iMac Intel 21,5" EMC 2805 Festplatte austauschen: Schritt 13, Bild 2 von 2
    • Zwänge die Plastikkarte erneut in die obere rechte Ecke ein und lasse sie dort stecken. Damit verhinderst du, dass sich die Teile wieder verkleben.

  14. iMac Intel 21,5" EMC 2805 Festplatte austauschen: Schritt 14, Bild 1 von 3 iMac Intel 21,5" EMC 2805 Festplatte austauschen: Schritt 14, Bild 2 von 3 iMac Intel 21,5" EMC 2805 Festplatte austauschen: Schritt 14, Bild 3 von 3
    • Setze eine zweite Plastikkarte an der oberen linken Ecke des iMac in den Spalt zwischen Rahmen und Display ein.

  15. iMac Intel 21,5" EMC 2805 Festplatte austauschen: Schritt 15, Bild 1 von 2 iMac Intel 21,5" EMC 2805 Festplatte austauschen: Schritt 15, Bild 2 von 2
    • Verdrehe die Karte nach oben, vergrößerte so den Spalt zwischen Rahmen und Display ein wenig.

    • Drehe, genau wie an der anderen Seite, langsam und lasse dem Klebstoff Zeit beim Auftrennen. Achte drauf, das Displayglas nicht zu stark zu belasten.

  16. iMac Intel 21,5" EMC 2805 Festplatte austauschen: Schritt 16, Bild 1 von 3 iMac Intel 21,5" EMC 2805 Festplatte austauschen: Schritt 16, Bild 2 von 3 iMac Intel 21,5" EMC 2805 Festplatte austauschen: Schritt 16, Bild 3 von 3
    • Fahre mit der Karte zur Mitte hin, halte auch hier wieder vor der iSight Kamera an

  17. iMac Intel 21,5" EMC 2805 Festplatte austauschen: Schritt 17, Bild 1 von 2 iMac Intel 21,5" EMC 2805 Festplatte austauschen: Schritt 17, Bild 2 von 2
    • Zwänge die Karte wieder bei der linken oberen Ecke ein.

  18. iMac Intel 21,5" EMC 2805 Festplatte austauschen: Schritt 18, Bild 1 von 3 iMac Intel 21,5" EMC 2805 Festplatte austauschen: Schritt 18, Bild 2 von 3 iMac Intel 21,5" EMC 2805 Festplatte austauschen: Schritt 18, Bild 3 von 3
    • Verdrehe nun beide Karten seitlich, wie im Bild zu sehen an den Ecken eingesetzt, und vergrößere den Spalt zwischen Gehäuse und Display.

    • Wenn manche Stellen noch verklebt erscheinen und sich nicht trennen lassen, dann musst du aufhören zu verdrehen und mit einer der Karten die Klebestelle auftrennen.

    • Fange an, die Oberkante des Displays vom Rahmen weg zu heben.

    • Hebe es nur ein paar Zentimeter an - die Datenkabel und Versorgungskabel des Displays sind immer noch am Logic Board angeschlossen.

  19. iMac Intel 21,5" EMC 2805 Festplatte austauschen, Kabel der Displayeinheit: Schritt 19, Bild 1 von 3 iMac Intel 21,5" EMC 2805 Festplatte austauschen, Kabel der Displayeinheit: Schritt 19, Bild 2 von 3 iMac Intel 21,5" EMC 2805 Festplatte austauschen, Kabel der Displayeinheit: Schritt 19, Bild 3 von 3
    • Klappe mit einer Pinzette den metallenen Sicherungsbügel am Displaydatenkabel hoch.

    • Ziehe das Displaydatenkabel vorsichtig aus seinem Sockel auf dem Logic Board.

    • Achte darauf, dass du den Stecker des Displaydatenkabels gerade aus dem Sockel herausziehst.

    Does anyone know where to find a replacement display cable for the 2014?

    PN: 923-00047

    PBMedic is out of stock

    Brian Hernandez - Antwort

  20. iMac Intel 21,5" EMC 2805 Festplatte austauschen: Schritt 20, Bild 1 von 2 iMac Intel 21,5" EMC 2805 Festplatte austauschen: Schritt 20, Bild 2 von 2
    • Während du das Display mit einer Hand nach oben hältst, trenne mit der anderen Hand das Stromkabel des Displays.

    • Hebe den Display nur so weit an, dass du genug Platz hast, um an den Anschluss zu kommen, jedoch nicht so weit, dass du die Kabel dehnst und ihre Anschlüsse überbeanspruchst (~20cm).

  21. iMac Intel 21,5" EMC 2805 Festplatte austauschen, Display: Schritt 21, Bild 1 von 2 iMac Intel 21,5" EMC 2805 Festplatte austauschen, Display: Schritt 21, Bild 2 von 2
    • Hebe das Display an, bis es fast senkrecht ist.

    • Es gibt immer noch einen Klebestreifen an der unteren Kante des Displays, der das Display wie eine Art Scharnier mit dem Gehäuse verbindet. Klappe das Display einige Male auf und zu, um den Kleber zu lösen.

  22. iMac Intel 21,5" EMC 2805 Festplatte austauschen: Schritt 22, Bild 1 von 2 iMac Intel 21,5" EMC 2805 Festplatte austauschen: Schritt 22, Bild 2 von 2
    • Wenn nötig, kann eine Plastikkarte helfen, den unteren Klebestreifen vollständig zu abzutrennen.

    Anyone else notice this iMac is different than the one in Step 20. The cables are in different places. I just saw one on YT like this, in a different country.

    Thomas Tommy - Antwort

  23. iMac Intel 21,5" EMC 2805 Festplatte austauschen: Schritt 23, Bild 1 von 3 iMac Intel 21,5" EMC 2805 Festplatte austauschen: Schritt 23, Bild 2 von 3 iMac Intel 21,5" EMC 2805 Festplatte austauschen: Schritt 23, Bild 3 von 3
    • Hebe das Display nach oben aus dem Rahmen und entferne es aus dem iMac.

    • Möglicherweise musst du an einer Seite anfangen, das Display anzuheben, um den Rest des Klebebandes zu lösen.

    • Sei vorsichtig bei der Handhabung des Display. Es ist groß, schwer und aus Glas.

    • Wenn du das Display durch ein neues ersetzen willst, musst du eventuell einige Bauteile vom alten auf das neue Display übertragen.

    • Schaue beim Zusammenbau in unsere Anleitung für den Displaykleber.

  24. iMac Intel 21,5" EMC 2805 Festplatte austauschen, Festplattenhalterungen: Schritt 24, Bild 1 von 1
    • Entferne folgende Torx T10 Schrauben, welche die Festplattenhalterung am Rückgehäuse befestigen:

    • Zwei 21 mm Schrauben an der linksseitigen Festplattenhalterung

    • Eine 9 mm Schraube

    • Eine 27 mm Schraube

    Pay attention to this photo and where the fan is. It is 180° from where the previous step shows it is oriented to you.

    Max Romano - Antwort

  25. iMac Intel 21,5" EMC 2805 Festplatte austauschen: Schritt 25, Bild 1 von 2 iMac Intel 21,5" EMC 2805 Festplatte austauschen: Schritt 25, Bild 2 von 2
    • Entferne die links- und rechtsseitige Festplattenhalterung vom iMac.

  26. iMac Intel 21,5" EMC 2805 Festplatte austauschen, Festplatteneinheit: Schritt 26, Bild 1 von 3 iMac Intel 21,5" EMC 2805 Festplatte austauschen, Festplatteneinheit: Schritt 26, Bild 2 von 3 iMac Intel 21,5" EMC 2805 Festplatte austauschen, Festplatteneinheit: Schritt 26, Bild 3 von 3
    • Hebe die Festplatte an der Kante nahe am Logic Board hoch und ziehe sie etwas aus ihrer Vertiefung heraus.

    • Die Festplatte ist noch über ein einzelnes SATA Daten/Versorgungskabel angeschlossen. Versuche nicht, sie ganz vom iMac zu entfernen.

    During the reassembly process I found it very difficult to plug the power/data cable on to the new hard drive. On my machine it’s very short and the fact that the cable comes into the plug from below at 90 degrees means it’s hard to keep straight on to the drive. I found this process could be made much easier by undoing 2 x T10 screws and CAREFULLY (there are cables attached) moving the adjacent speaker assembly a little away from the drive, reattaching once done. Hope this helps

    Jerry Frost - Antwort

    Moving the speaker helped tremendously! Thanks

    lucas -

  27. iMac Intel 21,5" EMC 2805 Festplatte austauschen: Schritt 27, Bild 1 von 3 iMac Intel 21,5" EMC 2805 Festplatte austauschen: Schritt 27, Bild 2 von 3 iMac Intel 21,5" EMC 2805 Festplatte austauschen: Schritt 27, Bild 3 von 3
    • Löse das SATA Daten/Versorgungskabel mit dem Spudger ab.

  28. iMac Intel 21,5" EMC 2805 Festplatte austauschen: Schritt 28, Bild 1 von 1
    • Entferne die Festplatte vom iMac.

    I found that there is one more torx screw underneath the hdd when you take it out. If you remove this it seems to be easier to reattach the SATA cable to the new drive.

    jeffjeffmurray - Antwort

  29. iMac Intel 21,5" EMC 2805 Festplatte austauschen, Festplatte: Schritt 29, Bild 1 von 2 iMac Intel 21,5" EMC 2805 Festplatte austauschen, Festplatte: Schritt 29, Bild 2 von 2
    • Löse die flexible Festplattenhülle von der oberen linken Ecke der Festplatte ab.

  30. iMac Intel 21,5" EMC 2805 Festplatte austauschen: Schritt 30, Bild 1 von 2 iMac Intel 21,5" EMC 2805 Festplatte austauschen: Schritt 30, Bild 2 von 2
    • Fahre mit dem Ablösen der Festplattenhülle aus der Klebeverbindung zum Laufwerk fort.

    • Entferne die Hülle von der Festplatte.

    • Die Festplatte bleibt übrig.

    Followed the instructions in this guide using the included tool that I got with the strips. Everything worked great. Put in a brand new Samsung 850 Evo 250GB Drive. The guide makes it sound a little bit more complicated but everything went pretty smooth. Just took it slow and easy.

    Michael Conrad - Antwort

    About torx is this good or what should I buy? https://www.amazon.it/gp/product/B00CIIM...=oh_aui_search_detailpage?ie=UTF8&psc=1

    Matteo Raggi - Antwort

    If replacing with an SSD, do you just use a mount? (I’ve don't this replacement in 27” models and the hard drive doesn’t have a silicone casing so I’m wondering how to get around this)

    Arispa Weigold - Antwort

    Great guide. I wanted to upgrade my late 2012 as much as I could to accommodate my large iTunes library. So with a little bit of cutting on the rubber hard drive cushion, I put a 15mm 5 TB hard drive and replaced the 120GB blade SSD with OWC’s 1 TB blade SSD. Now have 5.95 TB of fast usable space with my fusion drive.

    tednmandy - Antwort

    No temperature sensor issues on this? I know the 27” needs a temperature sensor adapter.

    Chris Harding - Antwort

    I couldn’t get the SATA cable connected again with the rubber sleeve on. Luckily my iMac had it in two separate pieces to stick to the long sides only, so I plugged it in first and carefully attached the bumpers after.

    Max Romano - Antwort

    What’s the trick to connect the SATA cable to the disk?? There’s very little play in the connector. Am unable to position it properly to get a connection. Maybe my fingers are too large.

    Also, the photos are a bit misleading with regard to disconnecting the data display cable - show tweezers pulling on the distal end of the cable, which, is very fragile. Pictures should be improved and better description of that step added.

    George Guess - Antwort

    Success! For those contemplating this, it takes some persistence and a perfect diagonal positioning of the SATA cable connector to attach the hard drive. Geez - Apple always seems to make things so easy for us average joes and janes.

    George Guess - Antwort

    I was very impressed with the instructions above, took my time and was patient all through. I had to spend some time in the installation of the OS, care is required and attention to restoring a good backup is necessary. I had great success and would recommend undertaking this task. Many thanks IFIXIT.

    Liam Foster - Antwort

    Successfully replaced harddrive when original crashed in Big Sur upgrade. Excellent instructions.

    Heikki Hanhimaki - Antwort

    Is the hard drive you remove accessible once removed? Can you pull data off the drive once removed? Great job explaining the removal process.

    Paul - Antwort

    Paul, you would have to get a external case inclosure to install the drive into. There are USB and SATA versions.

    B Jack - Antwort

    Since I unplugged a SATA cord to remove, will I need a SATA case? Gonna connect to new 24” iMac (M1) and try and grab the pics and music.

    Paul -

    The IFIXIT kit I bought included a SATA case, which I used to pull the data off the old hard drive which was on its last legs. Thank you, IFIXIT!

    This was my first attempt at opening an iMac for anything but RAM upgrade (when it was possible easily on older iMacs). I too took it easy and slow. Replacing the hard drive was the easiest part of all this! The hardest part, which I'm still struggling with, was unplugging and replugging the display data and power cables. I was able to install an OS on the new SSD but in order to close the machine I had to unplug the display cables, and it seems that one of them did not seat properly, since the computer starts up but the display is black. Sigh. I will have to do the cutting and pasting of the glue strips all over again. Apple really doesn't want us doing these repairs.

    Amacl - Antwort

Abschluss

Um dein Gerät wieder zusammenzusetzen, folge den Schritten in umgekehrter Reihenfolge.

70 weitere Nutzer:innen haben diese Anleitung absolviert.

Besonderer Dank geht an diese Übersetzer:innen:

en de

100%

Diese Übersetzer:innen helfen uns, die Welt zu reparieren! Wie kann ich mithelfen?
Hier starten ›

19 Kommentare

Is there a problem with the fan if I install SSD?

asrugo770 - Antwort

Yes. There is a thermal sensor, which is going crazy after replacement.

And also have a problem with kernel_task after upgrade...

markeev -

is there a solution about the termal sensor and the kernel_task issue?

Roberto Bonilla - Antwort

is there a solution about the termal sensor and the kernel_task issue?

i have the same problem, CPU 700 %…

roro974 - Antwort

I’ve run into the same thing: fans are running constantly with a new 1 TB 2.5” drive that I pulled from a 2012 iMac. I can use MacsFanControl as a 3rd party fix, but if anyone has a better (command line?) solution, I would be grateful!

Aaron Schine - Antwort

SSD Fan Control is doing the job perfectly !

Jose Vilar -

Thank you for posting this. Awesome! I am an IT Admin at a school and have Techie Students that help with the smaller things. One of the iMacs went bad. I had him follow this guide and he was able to replace the hard drive successfully!! Thank you!

Patti Braun - Antwort

What do you have to do with the temp sensor to make the fans behave normally after installing a SSD in an originally hard drive based iMac?

Andrew spoelstra - Antwort

Install the SSD into the HD bay and download the SSD Fan Control application to avoid fan noise (easier, but less legitimate)

Install the SSD into the HD bay with the OWC thermal sensor (Extremely difficult, considerably more expensive, but works properly). Link for thermal sensor: https://eshop.macsales.com/item/OWC/DIDI.... Link for SSD Fan Control: http://exirion.net/ssdfanctrl/

pfrohwein - Antwort

You should have installed the OWC inline thermal sensor.

MacFans is the only other solution.

https://eshop.macsales.com/item/OWC/DIDI...

rockpiano54 - Antwort

This guide is for the Mid-2014 21.5” 2808 machine, which does not have any thermal sensor on the STANDARD 2.5’” HDD. I just completed mine, and it’s totally silent, no fan issues as I’m typing this. I suggest some of the peeps above are posting in the wrong guide, and may have 27” machines with 3.5” HDD with the thermal sensor issue. A great guide, well written and illustrated, excellent 10/10.

Phil Reed - Antwort

Exactly. I just replaced my HD with an SSD and absolutely no fan noice.

Also a 21.5” imac a1418 emc 2805.

Pretty straight forward repair.

Christian Tørring -

I’ve just replaced the internal HDD by a Samsung 850 Pro SSD 256 GB. There is no need for any special cable, thermal sensor or additional software, the SSD runs fine. Model is a Mid 2014 iMac 21.5”, EMC 2805, 1.4 GHz i5, no Fusion Drive.

kriechel -

The issue with the fan is easily sorted with the software solution SSDfancontrol is free and works 99% of the time for me.

macfixer - Antwort

Outstanding kit by iFixit for replacing the HHD.

Great guide, I followed it step by step and had no problem but one: when reinserting the cable into the new SSD, I had no room for my fingers. I had to loose the black plastic cover to the left in order to have a bit more room and succeeded.

Then, I added an extra check before sealing the screen, powering on the Mac just to be sure I reconnected correctly the screen cables.

Now the Mac is super fast!

Aran Banjo - Antwort

Good guide, thank you very much :-)

Dariusz - Antwort

Thanks for the manual and the parts/tools to do this repair. It took me a lot more time than listed though :-)

David Shelton - Antwort

Pour faciliter le décollage, après avoir passé la roulette, j'insére tout autour des bandes de plastique dur de 2cm de large découpées sans un classeur en plastique. Ceci évite que ca recolle et l'écran se lève sans difficulté

Ordysouris - Antwort

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 11

Letzte 7 Tage: 60

Letzte 30 Tage: 251

Insgesamt: 55,126