Diese Version enthält möglicherweise inkorrekte Änderungen. Wechsle zur letzten geprüften Version.
Was du brauchst
-
-
Wenn das Glas deines Displays gesprungen ist, klebe es mit Klebeband ab, um weitere Brüche zu verhindern und Körperverletzungen während der Reparatur zu vermeiden.
-
Lege überlappende Streifen durchsichtiges Packband über das Display des iPads, bis die gesamte Fläche abgedeckt ist.
-
Versuche, den Rest der Anleitung genau wie beschrieben zu befolgen. Wenn das Glas jedoch einmal zerbrochen ist, wird es wahrscheinlich weiter zerspringen, während du arbeitest, und du musst eventuell ein Werkzeug aus Metall zum Hebeln verwenden, um das Glas herauszuholen.
-
-
-
Setze einen Spudger aus Metall zwischen der rechten Kante der Displayeinheit und der Rückabdeckung ein.
-
Drehe den Spudger von dir weg, um die Laschen an der oberen Kante des Displays zu lösen.
-
-
-
Setze einen zweiten Spudger aus Metall zwischen die obere Kante der Displayeinheit und die Rückabdeckung, damit die Laschen nicht wieder einrasten.
-
Heble die Displayeinheit von der Rückabdeckung ab.
-
-
-
Heble die Display Einheit entlang der unteren und linken Kante des iPads weiter von der Rückabdeckung ab.
-
-
-
Benutze das flache Ende eines Spudgers, um den Antennenstecker, der sich am nächsten an der Unterseite des iPads befindet, aus seinem Anschluss auf der Kommunikationsplatine zu hebeln.
-
-
-
In den folgenden Schritten wirst du die drei Kabel, die die Displayeinheit mit dem Logic Board verbinden, abtrennen. Die Kabel sind für die folgenden Komponenten:
-
Digitizer
-
Umgebungslichtsensor
-
Display-Datenkabel
-
-
-
Benutze die Kante eines iPod Öffnungswerkzeugs, um die Halteklappen hochzuklappen, die die Flachbandkabel des Touchscreens in ihren Anschlüssen auf dem Logic Board halten.
-
Ziehe die Flachbandkabel des Touchscreens gerade aus ihren Anschlüssen heraus.
-
-
-
-
Verwende ein iPod Öffnungswerkzeug, um den Stecker des Umgebungslichtsensors aus seinem Anschluss zu entfernen, indem du ihn vorsichtig nach oben hebelst.
-
-
-
Trenne das Datenkabel des Displays von der Hauptplatine, indem du die Metallhalterung an der schwarzen Kunststofflasche hochklappst.
-
Ziehe den Stecker des Kabels von seinem Anschluss ab.
-
-
-
Verwende die Kante des iPod-Öffnungswerkzeugs, um die Platine des Umgebungslichtsensors vorsichtig vom Kleber zu lösen, mit dem sie am Displayrahmen befestigt ist.
-
Wenn du ihn ausreichend gelöst hast, ziehe den Umgebungslichtsensor vorsichtig vom LCD ab.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
While holding the digitizer cable down, carefully peel back the piece of tape connecting the digitizer cable to the display frame.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Use the edge of an iPod opening tool to peel the antenna off the adhesive securing it to the top edge of the display.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Remove the three T5 Torx screws securing the clips and LCD brackets covered in EMI tape near the home button switch.
-
Carefully peel the display clip and its attached tape off the black plastic display frame.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Remove the remaining T5 Torx screws securing the LCD to the black plastic display frame.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Remove the small strip of tape securing the antenna lead to the LCD.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Insert the edge of an iPod opening tool under one of the ears attached to the steel LCD frame.
-
Twist the iPod opening tool to gently pry the LCD up off the adhesive securing it to the front glass panel.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Repeat the process detailed on the previous step to pry up the display around the three sides opposite the digitizer cable side of the display.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Lift the LCD from its free end, and remove it from the display frame.
-
Carefully peel the adhesive securing the long side of the LCD to the display frame, then remove the LCD.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
If it is still stuck to the front panel, remove the strip of EMI tape near the ambient light sensor socket.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
If they are still in good shape, transfer the clips and EMI tape near the bottom of the LCD to your new LCD.
-
Rückgängig: Ich habe diese Anleitung nicht absolviert.
41 weitere Nutzer:innen haben diese Anleitung absolviert.
4 Kommentare
Did this and everything worked great, but I forgot to re-attach the 3G antenna so I went back in to do that, closed it back up again and now my wifi isn't working. Any thoughts on what I likely messed up?
The first repair didn't require a software/firmware restore, but the second one did. I've restored twice now and reset network settings... all the suggestions Apple makes for troubleshooting a software issue, so I do think I messed something up inside.
Be very careful on step 14 as the piece of tape holding down the digitizer cable will TEAR your cable if not properly peeled. Ask me how I know.
to ifixit.com:
I'm very disappointed in the lack of caution advised during this step. Almost as if you wanted us to mess this up for the purpose of purchasing a digitizer from you. Shame.
A short remark about how much force will then be needed to separate the old battery from the heated adhesive would be helpful. I found that even after I was able to begin the insertion of a plastic card between the battery and the case, it required a great deal of force to push the card further under the battery to complete the separation. Refer: soundcloud converter
Thanks for this helpful steps, its clear and easy, Refer: children toys one and half olds