Einleitung
Benutze diese Anleitung, um das Logic Board in deinem iPad 3G zu ersetzen.
Was du brauchst
-
-
Wenn das Glas deines Displays gesprungen ist, klebe es mit Klebeband ab, um weitere Brüche zu verhindern und Körperverletzungen während der Reparatur zu vermeiden.
-
Lege überlappende Streifen durchsichtiges Packband über das Display des iPads, bis die gesamte Fläche abgedeckt ist.
-
Versuche, den Rest der Anleitung genau wie beschrieben zu befolgen. Wenn das Glas jedoch einmal zerbrochen ist, wird es wahrscheinlich weiter zerspringen, während du arbeitest, und du musst eventuell ein Werkzeug aus Metall zum Hebeln verwenden, um das Glas herauszuholen.
-
-
-
Setze einen Spudger aus Metall zwischen der rechten Kante der Displayeinheit und der Rückabdeckung ein.
-
Drehe den Spudger von dir weg, um die Laschen an der oberen Kante des Displays zu lösen.
Ok, a word of caution that can't be overstated. The off screen switch, the lock swith, and the volume switch can all be broken easily. I would stay away from this area completely. The bracket on the off switch is tack welded and can be broken. The volume/lock swith can be malformed to become unusable. So avoid the area and you will be better off.
Most of the spring clips mounted to the digitizer panel (sandwitched between the LCD display mount tabs and digitizer frame) are guaranteed to break. I recommend just purchasing a set (I found on one Amazon for less then $6). With that said, even though I broke most of mine while removing the glass panel/frame assembly, I was able to remount the glass. It seems fairly secure, but I'm going to put the iPad (3G/Wifi) in a case, anyway.
Pas besoin de pistolet a chaleur, il faut juste faire sauter les clips qui maintiennent l'ensemble écran et LCD. Bien commencer par la droite, car se sont juste des picots en plastique a faire sauter par dessus le rebord en alu, puis soulever la partie du bas en cassant les 4 clips ( pas moyen de les garder entier). Ensuite la partie gauche (avec 6 clips) se détachera facilement. La partie haute n'est pas éclipser mais retenus par un cable.
Yes, most of the clips break easily, but I was able to reassemble the iPad by putting the left side in first at an angle, and then snapping in the rest of it. Even though most of the clips break, it still holds together pretty tight.
not all clips break, and there are so many clips that despite breaking 2-3 clips it still fitted in nicely, if you do not have a metal spudger you can use any pack of screw drivers whose other end looks like the metal spudger, that’s about it, as far the instruction goes they are good for battery replacement.
-
-
-
Setze einen zweiten Spudger aus Metall zwischen die obere Kante der Displayeinheit und die Rückabdeckung, damit die Laschen nicht wieder einrasten.
-
Heble die Displayeinheit von der Rückabdeckung ab.
-
-
-
Heble die Display Einheit entlang der unteren und linken Kante des iPads weiter von der Rückabdeckung ab.
Be very careful as the left side has plastic pins that go into the cover, the right side and bottom have metal clips which break easily.
After unlocking the left side, pull away from the right side, as to save the metal clips.
During reassembly, it can be difficult to get the clips back into the body. I found that I had to put two (sturdy) metal spudgers on either side of the lower-right clip in order to gain enough space to get the clip into the body. Even then it required a fair amount of force (obviously not so much as to damage the display).
-
-
-
Hebe die Displayeinheit an der unteren Kante von der Rückabdeckung ab.
There are four black angle metal foil corner pieces that just fall out of the case. They are about 4 mm long and 2mm on each leg. Have no clue what they do or where they go.
That's probably broken Metal Display Clips. Easy to replace, but you'll need to purchase a set of new clips. Luckily, they're not expensive :-)
orb -
The display data cable may be glued into place along the right and top side of the right battery. You should use an iPod opening tool to pry it away from the adhesive. This will allow you to get a wider opening between the display and iPad body in order to access and remove other cables.
The photo above is the Wi-Fi version because the cellular communication board is missing in the photo. As I lifted the display, following the instructions, one of the cellular antennas snapped right out of the copper connector exposing bare wire. No big deal because it is an iPad 1 and no one would ever use cellular with an original iPad anyway. Not these days. But be very careful lifting the display because the antenna wires for the cellular board are very short and break easily.
-
-
-
Benutze das flache Ende eines Spudgers, um den Antennenstecker, der sich am nächsten an der Unterseite des iPads befindet, aus seinem Anschluss auf der Kommunikationsplatine zu hebeln.
The antenna cable is easily broken when separating the screen from body.
The whole antenna can be purchased for about $5 new on eBay.
Is there a tutorial? Mine broke and I did buy part. However, only thing I find is how to replace lcd. Just need how to replace 3G antenna.
I just need how to replace 3G antenna. Is there a tutorial? Mine broke and I did buy part. However, only thing that I find online is how to replace lcd.
-
-
-
In den folgenden Schritten wirst du die drei Kabel, die die Displayeinheit mit dem Logic Board verbinden, abtrennen. Die Kabel sind für die folgenden Komponenten:
-
Digitizer
-
Umgebungslichtsensor
-
Display-Datenkabel
-
-
-
Benutze die Kante eines iPod Öffnungswerkzeugs, um die Halteklappen hochzuklappen, die die Flachbandkabel des Touchscreens in ihren Anschlüssen auf dem Logic Board halten.
-
Ziehe die Flachbandkabel des Touchscreens gerade aus ihren Anschlüssen heraus.
-
-
-
-
Verwende ein iPod Öffnungswerkzeug, um den Stecker des Umgebungslichtsensors aus seinem Anschluss zu entfernen, indem du ihn vorsichtig nach oben hebelst.
-
-
-
Trenne das Datenkabel des Displays von der Hauptplatine, indem du die Metallhalterung an der schwarzen Kunststofflasche hochklappst.
-
Ziehe den Stecker des Kabels von seinem Anschluss ab.
For iPad Wifi Users, there is a ‘3D Antenna’’ cable that also needs to be removed. This is not covered in this tutorial. Here is a YouTube link to that covers this procedure. https://youtu.be/iD8kGSD5r0A
-
-
-
Benutze die Kante eines iPod Öffnungswerkzeugs, um den verbleibenden Antennen Stecker vorsichtig von der Kommunikationsplatine zu hebeln.
Replacing the communications board is a very delicate process. Be warned. I got to this point with only a bracket or two broken and when reseating the communications board, one of the connector wafers cracked. Hopefully it will still work but I suspect I will need to find a replacement.
-
-
-
Entferne das Kabel der Steuertaste an der oberen Kante der Kommunikationsplatine.
-
Ziehe das Kommunikationskabel nach oben, um seinen Stecker aus dem Anschluss auf dem Logic Board herauszuziehen.
-
-
-
Entferne die einzelne T5 Torx-Schraube, mit der die Kommunikationsplatine am Rückgehäuse befestigt ist.
-
-
-
Ziehe die EMI-Abschirmung aus Gummi, die den Anschluss für die GPS-Antenne abdeckt, vorsichtig ab.
-
Verwende die Kante eines iPod Öffnungswerkzeugs, um die Halteklappe des GPS-Flachbandkabels am Anschluss auf dem Logic Board hochzuklappen.
-
-
-
Benutze die Kante eines iPod Öffnungswerkzeugs, um die Halteklappe an der Kopfhörerbuchse/dem Anschluss für das Mikrofon aufzuhebeln.
-
Ziehe das Flachbandkabel für die Kopfhörerbuchse/das Mikrofon aus dem Anschluss.
-
-
-
Verwende ein iPod Öffnungswerkzeug, um den Stecker der SIM-Platine aus seinem Anschluss auf dem Logic Board herauszuhebeln.
Some iPads have a black tape that keeps the connector in place, you will have to remove it.
Cut the tape holding the SIM board connector to the logic board.
-
-
-
Biege das SIM-Kabel zur Unterseite des iPads, um an den Stecker des Lautsprechers zu gelangen.
-
Benutze die Kante eines iPod Öffnungswerkzeugs, um den Stecker des Lautsprechers nach oben und aus seinem Anschluss auf dem Logic Board herauszuhebeln.
-
-
-
Entferne die folgenden Schrauben, mit denen das Logic Board an der Rückabdeckung befestigt ist:
-
Zwei 4,56 mm T5 Torx Schrauben.
-
Zwei 3,76 mm T5 Torx Schrauben.
-
-
-
Benutze die Kante eines iPod Öffnungswerkzeugs, um den Stecker des Dock-Kabels vorsichtig nach oben vom Logic Board abzuhebeln.
-
Um dein Gerät wieder zusammenzubauen, folge den Schritten dieser Anleitung in umgekehrter Reihenfolge.
Um dein Gerät wieder zusammenzubauen, folge den Schritten dieser Anleitung in umgekehrter Reihenfolge.
Rückgängig: Ich habe diese Anleitung nicht absolviert.
10 weitere Nutzer:innen haben diese Anleitung absolviert.
Besonderer Dank geht an diese Übersetzer:innen:
100%
Annika Faelker hilft uns, die Welt in Ordnung zu bringen! Wie kann ich mithelfen?
Hier starten ›
Ein Kommentar
Did this and everything worked great, but I forgot to re-attach the 3G antenna so I went back in to do that, closed it back up again and now my wifi isn't working. Any thoughts on what I likely messed up?
The first repair didn't require a software/firmware restore, but the second one did. I've restored twice now and reset network settings... all the suggestions Apple makes for troubleshooting a software issue, so I do think I messed something up inside. wobble man 3d