Zum Hauptinhalt wechseln

iPad Displayeinheit verkleben (drei Klebestreifen)

Was du brauchst

  1. iPad Displayeinheit verkleben (drei Klebestreifen), iPad Displayeinheit verkleben (drei Klebestreifen): Schritt 1, Bild 1 von 2 iPad Displayeinheit verkleben (drei Klebestreifen), iPad Displayeinheit verkleben (drei Klebestreifen): Schritt 1, Bild 2 von 2
    • Bevor du neuen Kleber anbringen kannst, musst du erst die Displayeinheit und den Rahmen gründlich von allen Rückständen befreien.

    • Ziehe Reste von Klebestreifen mit einer Pinzette ab.

    • Schabe Kleberreste mit einem Plastiköffnungswerkzeug oder einem Spudger ab. Du kannst den Kleber mit hochkonzentriertem Isopropylalkohol (mehr als 90%ig) aufweichen.

    • Wische die Rückstände nur in einer Richtung ab, das verhindert ein Geschmiere.

    • Schabe nicht mit einem Metallwerkzeug, dadurch entstehen Kratzer auf der Oberfläche der Displayeinheit.

    I followed these instructions and used 99.9% isopropyl alcohol to clean off the glue around the display - but the isopropyl leaked under the screen and ruined it! Replacement screen more than the iPad’s worth. Use tiny amounts and don’t allow for any seepage, or try to manage without and just carefully scape. My iPad’s now a write-off… :-(

    Alex Harness - Antwort

    Hi Alex!

    I’m really sorry to hear about your experience. Can you describe a little more how the alcohol ruined the screen? This info can help with future guides!

    Arthur Shi -

    Use goof off or xylene on cotton swab outdoors to remove adhesive. Do it outside so you don’t smell up the house. Better than rubbing alcohol.

    macman2 - Antwort

    Goof-off will unfortunately leave a residue that can eventually weaken the replacement adhesive. Be sure to fully clean off the surface with alcohol after you use Goof-off.

    Arthur Shi -

    I used a hair dryer to soften the adhesive.

    OK, you still leave a very small, microscopic, layer of adhesive after removing the black tape, but really, new tape will still stick to that. We’re not trying to make the iPad water proof - we’re simply trying to make the components secure and not fall apart. Shame Apple couldn’t have used screws instead!

    Billinski - Antwort

    Used CRC Brakleen PRO SERIES. Applied sparingly with a Q-tip 2 inches at a time. Softened the adhesive was easily squeezed off with a plastic spudger.

    dklj - Antwort

  2. iPad Displayeinheit verkleben (drei Klebestreifen): Schritt 2, Bild 1 von 1
    • Lege die Ersatzklebestreifen passend an den richtigen Seiten um die Displayeinheit herum.

    Beim iPad Air müssen die Klebestreifen übrigens nicht auf das Gehäuse, sondern an das Front Panel geklebt werden.

    Veit Kunz - Antwort

    Danke. Sehr gut.

    Charles Farnsworth -

    Regarding which is the left side and which is the right side, do not rely on the color coding on the image in step 2. Instead, look for how the width of the adhesive strip varies. A thinner strip should correspond to the location of the screen side cables. I used the color coding on the image and got the sides reversed. However, even though there was too much adhesive near the side cables, it did not matter once I finished assembly. Another thing I did to make alignment easier is to cut the left and right sides in two close to the middle. It was easier to align the 4 strips working from corner to middle

    Rudy Chukran - Antwort

  3. iPad Displayeinheit verkleben (drei Klebestreifen): Schritt 3, Bild 1 von 2 iPad Displayeinheit verkleben (drei Klebestreifen): Schritt 3, Bild 2 von 2
    • Jeder Klebestreifen ist von vier Schichten von Plastik eingeschlossen - drei oben und einer unten.

    • Ziehe die oberste Plastikschicht vom linken Klebestreifen ab.

    • Ziehe die untere Plastikfolie vom Streifen ab.

    • Die Oberseite des Klebestreifens sollte immer noch mit einem farbigen Schutzfilm und einer durchsichtigen Plastikaussteifung bedeckt sein.

    • Die Unterseite des Klebestreifens sollte nun freigelegt und klebrig sein.

  4. iPad Displayeinheit verkleben (drei Klebestreifen): Schritt 4, Bild 1 von 2 iPad Displayeinheit verkleben (drei Klebestreifen): Schritt 4, Bild 2 von 2
    • Wenn sich auf dem Streifen Extrateilchen befinden, die du für dein iPad-Modell nicht brauchst, dann entferne sie jetzt.

  5. iPad Displayeinheit verkleben (drei Klebestreifen): Schritt 5, Bild 1 von 3 iPad Displayeinheit verkleben (drei Klebestreifen): Schritt 5, Bild 2 von 3 iPad Displayeinheit verkleben (drei Klebestreifen): Schritt 5, Bild 3 von 3
    • Richte den linken Klebestreifen an der linken Kante der Displayeinheit aus.

    • Fange an einer Ecke an und lege den Klebestreifen auf die Displayeinheit. Drücke ihn dann fest.

  6. iPad Displayeinheit verkleben (drei Klebestreifen): Schritt 6, Bild 1 von 3 iPad Displayeinheit verkleben (drei Klebestreifen): Schritt 6, Bild 2 von 3 iPad Displayeinheit verkleben (drei Klebestreifen): Schritt 6, Bild 3 von 3
    • Wiederhole das Verfahren für den rechten Klebestreifen.

    • Ziehe den obersten Klebefilm vom Streifen ab.

    • Ziehe die Schutzfolie an der Unterseite vom Streifen ab.

    • Richte den Streifen an der rechten Kante der Displayeinheit aus.

    • Beginne an einer Ecke und lege den Streifen auf die Displayeinheit. Drücke ihn dann fest.

  7. iPad Displayeinheit verkleben (drei Klebestreifen): Schritt 7, Bild 1 von 3 iPad Displayeinheit verkleben (drei Klebestreifen): Schritt 7, Bild 2 von 3 iPad Displayeinheit verkleben (drei Klebestreifen): Schritt 7, Bild 3 von 3
    • Wiederhole das Verfahren für den oberen Klebestreifen.

    • Ziehe den obersten Klebefilm vom Streifen ab.

    • Ziehe die Schutzfolie an der Unterseite vom Streifen ab.

    • Richte den Streifen an der Oberkante der Displayeinheit aus, sodass die gerade Klebelinie die Lücke zwischen dem linken und dem rechten Streifen überbrückt.

    • Drücke den Streifen fest.

  8. iPad Displayeinheit verkleben (drei Klebestreifen): Schritt 8, Bild 1 von 3 iPad Displayeinheit verkleben (drei Klebestreifen): Schritt 8, Bild 2 von 3 iPad Displayeinheit verkleben (drei Klebestreifen): Schritt 8, Bild 3 von 3
    • Ziehe die durchsichtige Aussteifung von allen drei Klebestreifen ab.

    • Die Klebestreifen sind immer noch mit farbigen Schutzfolien bedeckt.

  9. iPad Displayeinheit verkleben (drei Klebestreifen): Schritt 9, Bild 1 von 1
    • Setze den Zusammenbau fort, bis das Gerät endgültig zugeklebt werden kann.

  10. iPad Displayeinheit verkleben (drei Klebestreifen): Schritt 10, Bild 1 von 3 iPad Displayeinheit verkleben (drei Klebestreifen): Schritt 10, Bild 2 von 3 iPad Displayeinheit verkleben (drei Klebestreifen): Schritt 10, Bild 3 von 3
    • Ziehe die drei farbigen Schutzfolien ab, so dass die Klebeschicht freigelegt wird.

    • Schließe das Gerät und staple ein paar schwere Bücher darauf. Lasse sie dort für dreißig Minuten, so dass der Kleber gut abbinden kann.

    • Alternativ kannst du auch Display-Schraubzwingen verwenden, um den neuen Kleber abzubinden.

    Very clear and easy to do :)

    Maris - Antwort

Abschluss

Hat die Reparatur nicht den gewünschten Erfolg gebracht? In unserem Antwortenforum findest du Hilfe bei der Fehlersuche.

55 weitere Nutzer:innen haben diese Anleitung absolviert.

Besonderer Dank geht an diese Übersetzer:innen:

en de

100%

Diese Übersetzer:innen helfen uns, die Welt zu reparieren! Wie kann ich mithelfen?
Hier starten ›

Arthur Shi

Mitglied seit: 01/03/18

248.445 Reputation

503 Anleitungen geschrieben

Team

iFixit Mitglied von iFixit

Staff

136 Mitglieder

16.573 Anleitungen geschrieben

10 Kommentare

Thanks, I was able to fix my wife’s shattered digitizer screen on the iPad 6th gen with this guide!

Kevin Chatterton II - Antwort

I managed to get it done, but this was a personal nightmare for me and more difficult than replacing the battery in my ipad. There are too many instruction that say “remove plastic” and I have no idea which layer; there was nothing on the packaging to indicate which side was up or which side was the front and I ended up guessing the wrong direction because it “looked” right, but wasn’t. A simple sticker on the packaging indicating a direction would have removed all of the frustration. I only managed to figure it out by removing all of the plastic so that the sticky side of the adhesive was exposed and then I could finally see how it was supposed to fit and how I was supposed to press down with the other side of the plastic to push the adhesive side into the frame.

twizzlercraze72 - Antwort

Fixed a cracked iPad 4 mini screen; I agree with twizzlercraze72. Some kind of labeling would have saved so much peeling and re-sticking. I ended up with a gap next to my home button. An expensive lesson to learn.

CBrewington - Antwort

For me, actually replacing the battery wasn’t too bad, but I ended up using too much isopropyl to clean off the old glue, and it seeped under the display and ruined it. Wish Apple didn’t use so much glue. It massively impedes repairability, which is not very environmentally sound. My iPad was perfect apart from the battery - it’s now got a perfect battery but the iPad is ruined :-(

Alex Harness - Antwort

Same here :(. $50 repair just turned into $250!

Paul Manos -

I had the same thing happen. Lesson is not work so hard to remove the glue. :(

Charles Farnsworth -

I too thought it was the isopropanol that ruined the screen (even though I made sure it wouldn't go into the screen), but that stuff evaporates pretty quickly anyway. Your screen was most likely damaged just by opening the device with those picks (just like in my case) - a variety of people have reported the same thing. Turns out the instructions are just doing a really bad job at indicating how easy it is to damage the screen, and underestimate the force as well as time and heat required for the whole procedure. The German instructions are even worse. Even though the instructions give a warning, at one point they inexplicably also suggest it's "ok" to shove those picks into the display as far as the display bezel goes. If that's not going to ruin people screens, I don't know what is. And I personally think those "picks" are horrible choice for this repair. I never used them in any of my other repairs, but stupidly decided to work with them this time. This is by far one of the most difficult repairs.

Mac Stevenson -

would be WAY EASIER to align and install if designed to be applied on the FRAME instead of the SCREEN, the frame borders serve as guides, while the screen has none. Aside from a slight difficulty aligning the strips, it was simple to perform. Thanks!

nonyo - Antwort

Adhesive: Used CRC Brakleen PRO SERIES. Applied sparingly with a Q-tip 2 inches at a time. Softened the adhesive was easily squeezed off with a plastic spudger. Final cleaned with Isopropyl.

Application: Went as instructed including sick book method over night.

Result: Display is secure except on the upper left side ½” below the corner. This is the area where the adhesive narrows for about an inch. The narrowing is not necessary on an iPad Air 2. In hind site adding some Tesa 61395 Tape in the narrowed areas would have prevented reopening to redo the adhesive. At this point using B7000 adhesive may have been a better choice.

dklj - Antwort

AT LEAST THIS recognizes that taping the screen back in place is a non-trivial task. I have searched through multiple iPad ifixit repairs and they all say "Now that you have got it apart now just do the reverse with the good part".

FI's

Interesting the the tape is applied prior to reconnecting the digitizer

gerennichols - Antwort

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 16

Letzte 7 Tage: 151

Letzte 30 Tage: 701

Insgesamt: 38,485