Zum Hauptinhalt wechseln

iPad Wi-Fi LCD Austausch

Was du brauchst

  1. iPad Wi-Fi LCD Austausch, Display Austausch: Schritt 1, Bild 1 von 3 iPad Wi-Fi LCD Austausch, Display Austausch: Schritt 1, Bild 2 von 3 iPad Wi-Fi LCD Austausch, Display Austausch: Schritt 1, Bild 3 von 3
    • Wenn dein Displayglas Risse aufweist, dann musst du die Bruchstellen sichern und Verletzungen verhindern, indem du ein Klebeband auf die Glasscheibe klebst.

    • Lege überlappende Streifen durchsichtigen Klebebands über das Display des iPad, bis die ganze Scheibe bedeckt ist.

    • Dies hält Glasscherben zurück und hält die Scheibe zusammen, wenn das Display angehoben wird.

    • Tu dein Bestes, den Anweisungen genau zu folgen. Wenn das Glas jedoch zerbrochen ist, wird es wahrscheinlich weiter brechen, während du daran arbeitest. Du musst möglicherweise einen Metallspatel und eine Pinzette verwenden, um Glassplitter herauszuziehen.

    • Trage eine Schutzbrille, um deine Augen zu schützen, und achte darauf, den LCD-Bildschirm nicht zu beschädigen.

    1) Are you recommending to cover the display with clear packing tape even if it is intact (not cracked)?

    2) If so,will the tape take the display’s oleophobic coating with it when removed?

    Mitch Stary - Antwort

  2. iPad Wi-Fi LCD Austausch: Schritt 2, Bild 1 von 2 iPad Wi-Fi LCD Austausch: Schritt 2, Bild 2 von 2
    • In diesem Schritt wirst du die Display-Einheit vom Gehäuse trennen. Lies weiter und folge den Anweisungen genau, um Schäden am Display und den empfindlichen Halteklammern zu vermeiden.

    • Das Display wird von 14 Metallklammern am Gehäuse gehalten. Achte darauf, dass du mit dem Spatel um diese Klammern herum arbeitest und ihn nicht durch sie hindurch schiebst.

    • Falls dir doch einige Klammern brechen sollten, kannst du hier neue bekommen.

    A clearer explanation of the orientation is needed here. The bar code is at the top left of the iPad when you are looking at the screen.

    David Hincks - Antwort

  3. iPad Wi-Fi LCD Austausch: Schritt 3, Bild 1 von 2 iPad Wi-Fi LCD Austausch: Schritt 3, Bild 2 von 2
    • Setze einen Metallspatel zwischen die Oberkante der Display-Einheit und die Rückwandbaugruppe ein.

    • Drehe den Spatel von dir weg, um die Laschen entlang der oberen Kante des Bildschirms zu lösen.

    • Setze einen zweiten Metallspatel zwischen die Oberkante der Displaybaugruppe und die Rückwandbaugruppe ein, damit die Laschen nicht wieder einrasten.

    Tip* "ONLY WITH METAL SPUDGER* heat it with a lighter till its warm to touch, then slide it like a butter knife. it reduces chances of chipping glass.

    luckie - Antwort

    I've found that by using a thicker iPad tool dents the back less(not at all if your careful) and start prying just under the volume button and working my way down works better as the metal clips are on all sider except the right side.

    richard - Antwort

    It would be really helpful to point out where all the clips and tabs are, and to show a picture of them (unbroken), so you know what you're trying to release.

    Styg - Antwort

  4. iPad Wi-Fi LCD Austausch: Schritt 4, Bild 1 von 2 iPad Wi-Fi LCD Austausch: Schritt 4, Bild 2 von 2
    • Arbeite dich mit einem Spudger an der rechten Kante des iPads entlang.

    • Die Frontplatte wird durch Metallklammern oben, unten und links am Aluminiumrücken gehalten. Die rechte Seite hat Plastiklaschen, die in Aussparungen in der Rückplatte gleiten.

    • Sobald die Clips gelöst sind, hebe die linke Seite der Frontplatte nach oben und schiebe sie nach links, um die Laschen von der Aluminium-Rückplatte zu entfernen.

    • Heble sorgfältig und behutsam - sobald es irgendwo schwer geht, dann arbeite an einer anderen Stelle weiter.

    Its seems easier to undo the clips on the left and bottom by levering them with an iPad tool and pusing the clips in from the edge with another tool when i can visually see them. One the right side, bottom and most of the left side is done there isnt much need to do the top as it will slide off if moved about a centimeter

    richard - Antwort

  5. iPad Wi-Fi LCD Austausch: Schritt 5, Bild 1 von 1
    • Hebe die Display-Einheit an der Unterkante von der Rückwandbaugruppe weg.

    • Versuche jetzt noch nicht die Displaybaugruppe zu entfernen. Sie ist immer noch mit der Rückwandbaugruppe verbunden.

    By it's BOTTOM edge.

    jonathan - Antwort

  6. iPad Wi-Fi LCD Austausch: Schritt 6, Bild 1 von 1
    • In den folgenden Schritten trennst du die drei Kabel, mit denen die Display-Einheit am Logic Board befestigt ist. Die Kabel sind für folgende Komponenten vorgesehen:

    • Touchscreen

    • Umgebungslichtsensor

    • Display Datenkabel

    It would be easier to detach the Display Data Cable at its connector on the far right in the picture, since there doesnt seem to be much play to undo the suggested one.

    David Hincks - Antwort

  7. iPad Wi-Fi LCD Austausch: Schritt 7, Bild 1 von 3 iPad Wi-Fi LCD Austausch: Schritt 7, Bild 2 von 3 iPad Wi-Fi LCD Austausch: Schritt 7, Bild 3 von 3
    • Verwende die Kante eines Kunststofföffnungswerkzeugs, um die Halteklappen, die die Touchscreenkabel in ihren Buchsen auf dem Logic Board halten, hochzuklappen.

    • Achte darauf, dass du nur die Halteklappe nach oben klappst, nicht den Sockel selbst.

    • Ziehe die Touchscreen Flachbandkabel gerade aus den Sockeln heraus.

    Adding this comment in its proper place:

    After flipping up the metal retainer, pull it sideways.

    Do not pull it up vertically.

    Joe in PA

    David Hincks - Antwort

  8. iPad Wi-Fi LCD Austausch: Schritt 8, Bild 1 von 1
    • Verwende ein Kunststofföffnungswerkzeug, um den Verbinder des Umgebungslichtsensors aus seinem Sockel zu entfernen, indem du ihn vorsichtig nach oben hebelst.

  9. iPad Wi-Fi LCD Austausch: Schritt 9, Bild 1 von 2 iPad Wi-Fi LCD Austausch: Schritt 9, Bild 2 von 2
    • Löse das Display-Datenkabel von der Hauptplatine, indem du die Metallsicherung an der schwarzen Plastikzuglasche hochklappst.

    • Ziehe den Verbinder aus dem Sockel.

    • Ziehe den Verbinder parallel zur Oberfläche des Logic Boards.

    IMHO, unhooking data display cable from the other end is preferable to the above location, since the cable itself is sealed or taped onto the assembly.

    Roger Buttermore - Antwort

  10. iPad Wi-Fi LCD Austausch: Schritt 10, Bild 1 von 1
    • Entferne die Display-Einheit von der Rückwandbaugruppe.

  11. iPad Wi-Fi LCD Austausch, Umgebungslichtsensor: Schritt 11, Bild 1 von 3 iPad Wi-Fi LCD Austausch, Umgebungslichtsensor: Schritt 11, Bild 2 von 3 iPad Wi-Fi LCD Austausch, Umgebungslichtsensor: Schritt 11, Bild 3 von 3
    • Wenn du dein LCD wieder verwendest, ist es nicht nötig den Umgebungslichtsensor von der Rückseite des LCD abzulösen.

    • Löse die Klebeverbindung der Umgebungslichtsensoreinheit am Displayrahmen vorsichtig mit der Kante eines Plastiköffnungswerkzeugs ab.

    • Wenn du sie ausreichend gelöst hast, kannst du sie ganz vom LCD entfernen.

    • Achte darauf du den Umgebungslichtsensor nicht unterhalb seines Oberteils abknickst, der Teil mit dem Klebestreifen könnte sonst abbrechen.

    • Falls nötig musst du vor Zusammenbau das Plastikfenster an deinem neuen Umgebungslichtsensor anbringen.

    You can leave the sensor stuck to the LCD if you're reusing the LCD. It just stays attached to the LCD no problem.

    jonathan - Antwort

    Step 7 after flipping up the metal retainer, pull it sideways.

    Do not pull it up vertically.

    Joe in PA - Antwort

    I added your comment in the proper place at Step 7

    David Hincks -

  12. iPad Wi-Fi LCD Austausch, LCD: Schritt 12, Bild 1 von 1
    • Drücke das Touchscreen Kabel nach unten und ziehe sorgfältig das Stück Klebeband, welches das Touchscreen Kabel am Displayrahmen befestigt, ab.

  13. iPad Wi-Fi LCD Austausch: Schritt 13, Bild 1 von 2 iPad Wi-Fi LCD Austausch: Schritt 13, Bild 2 von 2
    • Entferne die drei Torx T5 Schrauben, die die Klammern und LCD Halterungen, welche mit Abschirmband bedeckt sind, in der Nähe des Home Schalters befestigen

    • Ziehe sorgfältig die Displayklammer und das daran befestigte Klebeband vom schwarzen Plastikrahmen des Displays ab.

    • Wenn du das LCD austauschst, musst du diese Stücke Abschirmband samt Klammern auf die neue LCD übertragen.

  14. iPad Wi-Fi LCD Austausch: Schritt 14, Bild 1 von 1
    • Entferne die restlichen T5 Schrauben, die das LCD am schwarzen Displayrahmen aus Plastik befestigen.

    I see that the author broke 4 tabs on the top and 2 tabs on the bottom -- the exact same ones that I broke. I must be following his instructions perfectly!

    Styg - Antwort

  15. iPad Wi-Fi LCD Austausch: Schritt 15, Bild 1 von 2 iPad Wi-Fi LCD Austausch: Schritt 15, Bild 2 von 2
    • Setze ein Plastiköffnungswerkzeug unter eine der Ausbuchtungen am metallenen LCD Rahmen.

    • Verdrehe das Werkzeug vorsichtig, um das LCD aus der Klebeverbindung zur Frontscheibe zu lösen.

    • Verbiege das LCD nicht zu stark, es ist ja aus Glas.

  16. iPad Wi-Fi LCD Austausch: Schritt 16, Bild 1 von 1
    • Wiederhole diesen Schritt für alle drei Seiten gegenüber der Seite des Displays mit dem Touchscreen Kabel, um das Display hochzuheben.

  17. iPad Wi-Fi LCD Austausch: Schritt 17, Bild 1 von 2 iPad Wi-Fi LCD Austausch: Schritt 17, Bild 2 von 2
    • Hebe das LCD an der freien Seite hoch und entferne es aus dem Displayrahmen.

    • Ziehe sorgfältig das Klebeband ab, welches das LCD an der langen Seite am Displayrahmen befestigt, entferne dann das LCD.

    remove the home button spring assembly from the old digitizer and transfer it to the new one!!!!!!!!!

    wh1513 - Antwort

  18. iPad Wi-Fi LCD Austausch: Schritt 18, Bild 1 von 1
    • Wenn es dann immer noch am Front Panel festhängt, musst du den Streifen Abschirmband in der Nähe des Sockels des Umgebungslichtsensors entfernen.

    • Übertrage es auf das neue LCD, falls nötig.

    • Wenn es am LCD befestigt ist und du benutzt wieder das alte LCD weiter, kannst du diesen Schritt überspringen. Wenn du aber ein neues LCD verwendest, musst du den Abchirmklebestreifen übertragen.

    Jeez!! Please put to keep the emi tape if you are resusing your lcd BEFORE the step that says to remove it...I don't know how import this stuff is, but I'm guessing pretty important cause I just removed it.

    Noah - Antwort

  19. iPad Wi-Fi LCD Austausch: Schritt 19, Bild 1 von 1
    • Wenn sie noch in gutem Zustand sind, kannst du die Klammern samt Abschirmband unten am LCD auf das neue LCD übertragen.

Abschluss

Um dein Gerät wieder zusammenzusetzen, folge den Schritten in umgekehrter Reihenfolge.

78 weitere Nutzer:innen haben diese Anleitung absolviert.

Besonderer Dank geht an diese Übersetzer:innen:

en de

100%

Diese Übersetzer:innen helfen uns, die Welt zu reparieren! Wie kann ich mithelfen?
Hier starten ›

4 Kommentare

So what if ive snapped off one of the retaining flaps? Ive seen in the past when ive snapped them off before i could just plug it in, slap on some kapton tape and it was fine. This time i cant get the bottom of the digitizer to work on new glass. I put on the old glass and the bottom works just fine. the bottom flap is the one that broke, but why would the old glass work just fine, but the new glass does nothing on the bottom half?

Blib - Antwort

Just replaced my lcd using this guide. Not easy, but doable. Took about an hour and a half. broke about half of the clips that hold the assembly in, but moved the remaining ones around so that it is secure. I recommend buying replacement clips if you aren't comfortable with that. Also, this guide says to use a Torx T5 screwdriver. Other sites say T4. It is most definitely T5. I bought the wrong one first and had to get a new one. Home Depot has an 8 in 1 Torx tool for 6 bucks that is great. Thank you iFixit for saving me hundreds that I would have spent on a new iPad!

dcook88 - Antwort

Don't worry about buying more replacment clips -- if you still have them on the left edge, not having the clips on the top and bottom isn't noticeable.

Styg -

When reassembling at the last step (inserting the screen assembly into the back cover), do NOT simply do the reverse of what you did to take it out. Instead, insert the right edge first (with the plastic tabs). The metal tabs on the left edge (and top and bottom edges if you have any left) are flexible, so it is very easy to snap the left edge of the screen into the back cover AFTER the right edge is in place. If you put the left edge in first, you'll have a much tougher time trying to get the plastic tabs on the right edge into back cover.

Styg - Antwort

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 1

Letzte 7 Tage: 6

Letzte 30 Tage: 55

Insgesamt: 211,363