Ersatzteile

Kein Ersatzteil erforderlich.

  1. Löse mit der Kante eines Platsic Opening Tools Ohrhörer und Lautsprecher von dem Schaumkleber, mit dem sie am iPhone festgemacht sind. Wenn du den Ohrhörer und Lautsprecher wiederverwenden willst, versuche den Schaumkleber, mit dem sie am iPhone Gehäuse festgemacht sind, nicht abzulösen.
    • Löse mit der Kante eines Platsic Opening Tools Ohrhörer und Lautsprecher von dem Schaumkleber, mit dem sie am iPhone festgemacht sind.

    • Wenn du den Ohrhörer und Lautsprecher wiederverwenden willst, versuche den Schaumkleber, mit dem sie am iPhone Gehäuse festgemacht sind, nicht abzulösen.

    • Entferne Ohrhörer und Lautsprecher.

    Go ahead and order a new speaker - its nearly impossible not to break the foam

    nweeks - Antwort

    The foam can be replaced by similar double side tape.

    davidsotl -

    Tools plus parts plus shipping (FedEx) costs me about $100. Probably would cost about the same to have some do it for me, but what's the fun in that! The small magnetic mat is a must have, so handy.

    davidsotl - Antwort

    Agree with "nweeks" on it being impossible not to break the foam. However, I reinstalled without the foam. Since the earpiece is wrapped in the ribbon cable and it's also very securely contained in the recess, I can't see the foam adding a ton of value. My phone worked fine after I reused the earpiece without any new foam.

    Song - Antwort

    Its really easy to remove the foam and tape intact and re-use. grab an exacto blade and slice in between the flex cable and foam, once you have the edge started it will sparate pretty easily. dont worry about damaging the cable, you're replacing that anyway.

    Andrew - Antwort

    I tried this and it worked easily. Thanks for the tip.

    davisyang -

    Does it matter which orientation the earpiece gets reattached to the cable?

    Robert Lindsley - Antwort

    The second piece of tape was missing on the new speaker I purchased. The speaker buzzes for voice except for loud/slow speaking.

    wmarkwitherspoon - Antwort

    On reassembly, fix the earphone speaker before the top sensor assembly. The first step is to glue the Power and Sensor Cable down on the iPhone base. Then put the earphone speaker on top of the cable, oriented as in the photos. Then bend the cable over the speaker and reassemble the top sensor assembly.

    gregm - Antwort

    Note: be sure that the foam on your brand-new replacement sticker is centered properly! Mine was originally glued down onto the speaker improperly - off-center. This made the foam touch the actual speaker diaphragm instead of just sitting on the case, and made it extremely quiet - almost inaudible. It took two tear-downs for me to think of trying to re-seat the foam, but it immediately fixed the problem.

    jil24 - Antwort

  2. Kostenloser Versand für alle Bestellungen über 100 $ oder mit einem Pro Tech Toolkit!

    Schau dich im Store um
Abschluss

Arbeite die Schritte in umgekehrter Reihenfolge ab, um dein Gerät wieder zusammenzubauen.

Besonderer Dank geht an diese Übersetzer:

100%

Jasper Fleischhauer hilft uns, die Welt in Ordnung zu bringen! Wie kann ich mithelfen?
Beginne zu übersetzen ›

Kommentar hinzufügen

Statistik anzeigen:

Letzte 24 Stunden: 0

Letzte 7 Tage: 0

Letzte 30 Tage: 0

Insgesamt: 708