iPhone 4S SIM Karte ersetzen

Einleitung

Prerequisite um Logic Board zu entfernen

Was du brauchst

Schritt 1 SIM Karte

iPhone 4S SIM Karte ersetzen, SIM Karte: Schritt 1, Bild 1 von 2

iPhone 4S SIM Karte ersetzen, SIM Karte: Schritt 1, Bild 2 von 2

Entferne die SIM-Karte und den SIM-Einschub mit Hilfe eines SIM Card Eject Tools oder einer Büroklammer.
Dies kann beträchtlichen Krafteinsatz erfordern.
Entferne die SIM-Karte und den Einschub vom iPhone.

Übersetzen

I have an Iphone 4 but the inerds look more like this 4S than the 4, except I do not have a SIM card port. What's up?

Dave - 25. Jan 2013 Antwort

Probably a CDMA (Verizon) iPhone 4.

Pepper - 11. Feb 2013

Is there a reason for waiting until step 18 to remove the sim card and its holder? I can do it right before I start without much force, is this not better?

jmaelzer - 18. Feb 2013 Antwort

I don't see any reason. So it was my step 1 to remove the SIM card.

Ida - 25. Jul 2014

I agree that the SIM card should be removed before you even start. After I completed this repair (waiting until this step to remove the SIM), the SIM card and holders won't go flush with the side of the phone anymore. The phone still works and everything else is fine, it's just annoying that I have a SIM holder sticking out about 1mm. I'm not certain this step caused this, but I'm just letting folks know that I agree with jmaelzer.

Song - 3. Aug 2013 Antwort

for the life of me I can NOT get this sim card and holder out!

Lori - 25. Okt 2013 Antwort

While "This may require a significant amount of force." may vary by individual device, I found it to be true. I used a straightened paper clip held with a (really good) pair of needle nose pliers and pushed straight in until it fully popped out.

Orac - 17. Dez 2016

To be honest, it's really hard to remove SIM card without a correct tool.

Beck Sisyphus - 25. Dez 2013 Antwort

You have to PUSH the paperclip IN, then the tray pops OUT.

Floris Jansen - 21. Jan 2014 Antwort

I agree. Push in.

ivesrubl - 21. Mai 2014

ifixit needs to edit this: "significant force" is NOT needed! I started to bend out the hole until I read the last post- just push the tool straight in, the SIM card will eject easily.

soopamandan - 23. Aug 2014 Antwort

That may depend on the specific device; significant force *was* needed to eject it in the case of the phone I'm working on. Putting it back in, however, was very easy and didn't require any significant effort.

Orac - 17. Dez 2016

Is there any reason why you still have the ribbon cable under the little metalic plate (right under the sticker that says "Authorized Service Provider Only") plugged in in STEP 10. And it is without any instruction step removed in STEP 12? I mean it's not like it is complicated, but when I got to that part I was confused there for a minute that I forgot some step, and then reassured myself that I did everything as it said in the manual.

[deleted] - 8. Sep 2014 Antwort

I have done everything correctly but when i turn the phone on all i get is a blank screen. The phone operates as normal i.e. it rings, vibrates etc but the screen is just blank so you can't actually do anything with it :(

anyone had the same issue?

mark - 19. Jan 2015 Antwort

FWIW, I found it easier to replace during re-assembly by turning the phone front-side up, as on the Sprint-locked one I was working on, the SIM card faces that way. Otherwise, it tends to fall out (down) while trying to re-insert it if the phone is face down.

Orac - 17. Dez 2016 Antwort

Popped the SIM card holder out no prob - but there’s no SIM card. This is a Virgin Mobile phone, does that matter?

Ray - 22. Okt 2017 Antwort

There is a rubber spring that fits on the power button hinged wire bar that slipped out of place here (button was stuck, no click), take a look at it here: http://geulah.net/test/

uhf mhz - 10. Feb 2020 Antwort