Zum Hauptinhalt wechseln

iPhone 6 Plus LCD und Touchscreen tauschen

Was du brauchst


  1. iPhone 6 Plus LCD und Touchscreen tauschen, Pentalobe Schrauben: Schritt 1, Bild 1 von 1
    • Entlade dein iPhone auf unter 25%, bevor du es demontierst. Eine geladene Lithium-Ionen-Batterie kann Feuer fangen und/oder explodieren, wenn man sie aus Versehen ansticht.

    • Schalte dein iPhone ab, bevor du mit der Demontage beginnst.

    • Entferne die beiden 3,6 mm P2 Pentalobe Schrauben neben dem Lightning Connector.

    I prefer to remove the SIM card as the very first step since it's safer to do so while the phone is fully assembled.

    estebanfallasf - Antwort

    I stripped one of the two screws - at a dead stop.

    Margaret Patterson - Antwort

    Before you even start: get the iOpener or hairdryer out. You’ll need it

    GPZ - Antwort

    If a lightning connector won’t provide a charge or needs to be wiggled carefully to provide a charge, power off the device, then try using precision tweezers to scrape the innermost wall of the lightning jack in a pinching motion to check for lint buildup. Pocket lint or other debris can accumulate inside the jack, compacting each time a cable is inserted. This can prevent a lightning cable from seating fully. Clearing the lint may restore functionality without replacing the part.

    Andrew Dolan - Antwort

    A few hints:

    * heating up the phone works great. I used a heating pad that you put in the microwave to heat sports injuries.

    * also, I made a sheet to help you keep track of the screws as you remove them. Print out the page, then place double sided tape below each color-coded listing of screws, and stick the screws to the tape as you disassemble. This helps prevent losing the screws and keeps track of what screws are what for easier reassembly. https://drive.google.com/file/d/1pLSvKvB...

    Paul Faulstich - Antwort

    Additional hints, for anyone who needs them:

    * stick the screws to the tape in the same positions as they are shown in the guide. This will make it easier to identify them during reassembly.

    * if the screws get mixed together, the ‘mm’ (millimetre, millimeter) measurements given in the guide can be used to identify them. Compare the lengths of the threaded shafts to each other to determine which screw is which.

    Friendly Advice -

  2. iPhone 6 Plus LCD und Touchscreen tauschen, Ein Display mit Klebeband bedecken: Schritt 2, Bild 1 von 3 iPhone 6 Plus LCD und Touchscreen tauschen, Ein Display mit Klebeband bedecken: Schritt 2, Bild 2 von 3 iPhone 6 Plus LCD und Touchscreen tauschen, Ein Display mit Klebeband bedecken: Schritt 2, Bild 3 von 3
    • Wenn dein Display zerbrochen ist, dann solltest du ein weiteres Zerbrechen verhindern und Verletzungen während der Reparatur vermeiden, indem du Klebeband auf der Glasscheibe befestigst.

    • Klebe überlappende Streifen von durchsichtigem Paketband über das Display des iPhones, bis die ganze Frontscheibe bedeckt ist.

    • Das hält die Glasscherben zusammen und sorgt füreigen strukturellen Zusammenhalt beim Hebeln und Hochheben des Displays.

    • Schütze deine Augen während der Reparatur mit einer Schutzbrille vor herausfliegenden Glassplittern.

    • Wenn die Scheibe so stark geplittert ist, dass du den Saugheber während der nächsten Schritte nicht ansetzen kannst, dann kannst du versuchen, ein sehr starkes Stück Klebeband (etwa Panzerband) zu einem Griff zu falten und aufzukleben. Versuche dann das Display damit anzuheben. (so wie im dritten Bild gezeigt)

    Tape doesn’t hold. suction cup doesn’t work. Tape folded over doesn’t work as a handle. I’ve used 3m’ s Gorilla duct tape. The glass is so shattered I cant get a point started to remove the glass. Phone has been in an otter box for years. dropped it and shattered glass while replacing case. Now what?

    Martin Speedy - Antwort

    When all else fails, you can superglue your suction cup (or tape) to the display, wait for it to cure, and pull.

    Jeff Suovanen -

    I had issues getting the suction cup to stick on my cracked screen, so I tried using scotch tape (only tape I had around), but it didn’t work. This best thing I did was to forcefully pry the screen off (I wasn’t worried about damages because it’s already cracked) with the spudger. I think its best to find something stickier (like Duct Tape) and used that to lift up the screen.

    Definitely surprised how sticky the adhesive was.

    Jeffrey Robinos - Antwort

    When using packing tape: the suction won’t hold well with the overlapping pieces, so add a square of tape where you want to put the suction cup, so it will provide an unbroken surface for the seal.

    Christa - Antwort

    It’s amazing how a heat gun or hair dryer makes life easier to soften up the adhesive. Then use a thin iSesame opening tool to get in under the screen (start @ 90 degrees/vertical either side of the home button & slowly go horizontal) the need to use suction cups. Run the opening tool along the front and down both sides to cut the adhesive before trying to lift the screen.

    Cheers Wayne

    Wayne Lyell - Antwort

    I didn’t have a hair dryer so I (gingerly) used an iron over some wet coffee filters (I mean , it is waterproof) . Then, quickly dried i off with paper towels, used gorilla tape and my fixit metal splunger . worked like a charm .

    MajorCouillon - Antwort

    What about baby cracks? skip to step 3 or not…

    Andruw Holland - Antwort

    As others have mentioned, suction cup and tape doesn’t work. I used the blade of a box cutter (watch fingers) and inserted just below and right of home button. Then moved spudger along the crack to tear adhesive/seal. Easy peasy.

    Stephen Smith - Antwort

  3. iPhone 6 Plus LCD und Touchscreen tauschen, Anweisungen für die Anti-Clamp: Schritt 3, Bild 1 von 3 iPhone 6 Plus LCD und Touchscreen tauschen, Anweisungen für die Anti-Clamp: Schritt 3, Bild 2 von 3 iPhone 6 Plus LCD und Touchscreen tauschen, Anweisungen für die Anti-Clamp: Schritt 3, Bild 3 von 3
    • In den nächsten beiden Schritten wird die Verwendung der Anti-Clamp gezeigt, ein Werkzeug, das wir entwickelt haben, um den Öffnungsvorgang zu erleichtern. Wenn du die Anti-Clamp nicht verwendest, überspringe die ersten drei Schritte, um eine alternative Methode zu finden.

    • Eine ausführliche Anleitung zur Verwendung der Anti-Clamp findest du in dieser Anleitung.

    • Ziehe den blauen Griff nach hinten, um die Arme der Anti-Clamp zu entriegeln.

    • Schiebe die Arme entweder über die linke oder rechte Kante deines iPhones.

    • Positioniere die Saugheber nahe an der Unterkante des iPhones direkt über dem Home Button - einen auf der Vorderseite und einen auf der Rückseite.

    • Drücke die Saugheber zusammen, um sie auf der gewünschten Stelle zu befestigen.

    • Wenn du feststellst, dass die Oberfläche deines iPhones für die Anti-Clamp zu rutschig ist, kannst du mit Klebeband eine griffigere Oberfläche schaffen.

  4. iPhone 6 Plus LCD und Touchscreen tauschen: Schritt 4, Bild 1 von 3 iPhone 6 Plus LCD und Touchscreen tauschen: Schritt 4, Bild 2 von 3 iPhone 6 Plus LCD und Touchscreen tauschen: Schritt 4, Bild 3 von 3
    • Ziehe den blauen Griff nach vorne, um die Arme zu verriegeln.

    • Drehe den Griff im Uhrzeigersinn um 360 Grad oder bis die Suagheber anfangen, sich zu dehnen.

    • Achte darauf, dass die Saugheber zueinander ausgerichtet bleiben. Wenn sie zu verrutschen beginnen, löse die Saugheber etwas und richte die Arme neu aus.

    • Setze ein Plektrum oder ein Öffnungswerkzeug unter das Display ein, wenn die Anti-Klemme einen ausreichend großen Spalt erzeugt hat.

    • Wenn die Anti-Clamp keinen ausreichend großen Abstand bildet, drehe den Griff um eine Vierteldrehung.

    • Drehe den Griff nicht mehr als eine Vierteldrehung auf einmal und warte zwischen den einzelnen Umdrehungen ein paar Sekunden. Lasse die Anti-Clamp und die Zeit die Arbeit für dich machen.

    • Überspringe die nächsten drei Schritte.

    Use clear nontextured tape place that over the phone screen. Refer to any guide that addresses replacing a shattered screen

    Abigail Cherry - Antwort

    I know it's tough with cracked glass. You just need enough to get in a plstic pry tool or guitar pick. Then you can pry it apart. Just be patient, I cannot stress that enough; the electronics are very, very small and fragile.

    Mike - Antwort

  5. iPhone 6 Plus LCD und Touchscreen tauschen, Display Einheit: Schritt 5, Bild 1 von 1
    • Benutze einen einzelnen Saugheber, um die Display-Einheit anzuheben:

    • Drücke einen Saugheber auf das Display, direkt über (aber nicht auf) den Home Button.

    • Drücke den Saugheber gut auf der Scheibe fest, damit er sicher haften bleibt.

    • Wenn die Scheibe stark gesplittert ist, haftet der Saugheber möglicherweise nicht gut. Klebe eine Lage von durchsichtigem Paketband darüber, damit er besser festhält. Du kannst auch anstelle eines Saughebers sehr starkes Klebeband verwenden. Eine weitere Möglichkeit ist, den Saugheber mit Sekundenkleber zu befestigen.

    Avec la ventouse, l’ouverture est brutale, tout s’est déclipsé d’un seul coup. Faire attention.

    Paul Briffaut - Antwort

    English Please!

    tom mozeleski -

    With the sucker, the opening is brutal, everything was cleared at once. Pay attention. (Paul’s comment translated by Google)

    Steve Schlotter - Antwort

    May need to burp the sticker before it sticks. Need to let the air out. Once Idid that, no problem. Except it was still hard to get the cover to start up.

    Patricia Tucker - Antwort

    Don’t waste your time with the suction cup - it doesn’t work! insert the blade of a box cutter just below the lower screen edge below the home button and gently pry just enough to start cracking the seal.

    Stephen Smith - Antwort

  6. iPhone 6 Plus LCD und Touchscreen tauschen: Schritt 6, Bild 1 von 1
    • Ziehe an dem Saugnapf während du das iPhone mit der anderen Hand festhältst, um die Displayeinheit etwas von der Rückseite anzuheben.

    • Nimm dir Zeit und wende gleichbleibend feste Kraft an. Die Displayeinheit sitzt sehr viel passgenauer im Gerät als viele andere Teile.

    • Benutze ein Plastik Opening Tool, um vorsichtig die Rückseite nach unten zu drücken, weg von der Display Einheit, während du das Display weiter mit dem Saugnapf nach oben ziehst.

    • Mehrere Clips befestigen die Display Einheit im Gehäuse, weshalb du vielleicht den Saugnapf und ein Plastik Opening Tool brauchst, um die Displayeinheit von der Rückseite zu lösen.

    Be extra careful here. If you don’t take your time, your front panel may jerk back on you, causing you to overextend and break the front camera/mic flex cable; happened to me. Slowly peel back the front panel, opening it no more than 90º.

    Thomas - Antwort

    watch out for the left side of the phone the adhesive bunches up around the inner clips, i didn’t realize it and the upper left of my screen cracked pretty bad. But this guide is awesome follow every direction to the letter

    Aaron Fitzpatrick - Antwort

    Note: this comment is written for the iPhone 6 Plus, but may also apply to other models of iPhone.


    The clips in the rear case attach to small slotted shapes under the edges of the display assembly, and these attachment points alternate from one side to the other. Moving from bottom to top, gently pulling the rear case away at these points will help to separate the two halves without using too much force.


    Ensure that the plastic clips along the top edge of the front panel (shown in step 8) are fitted properly inside the rear case, then gently press the display assembly into the rear case at these points, moving from top to bottom. There may be a small click sound as the clips in the rear case engage with the slots on the display assembly, and the rear case should fit flush with the edges of the display assembly.

    Friendly Advice - Antwort

    This was challenging. For me, the suction cup could only create a tiny bit of motion and at first, no actual gap at all. You might have to pull the suction cup away from the base a few times just to loosen things up a tiny bit. Eventually, I got my fingernail in, and then after a few minutes got the plastic tool in.

    Also, use the plastic tool to gently pry along the sides of the phone once there’s light there. I was afraid of using too much leverage and breaking the screen as per the other comments, but starting at the bottom and then going around the sides slowly worked for me.

    FixingMyiPhone - Antwort

  7. iPhone 6 Plus LCD und Touchscreen tauschen: Schritt 7, Bild 1 von 2 iPhone 6 Plus LCD und Touchscreen tauschen: Schritt 7, Bild 2 von 2
    • Ziehe an der Plastiknoppe, um das Vakuum des Saugnapfes zu lösen.

    • Entferne den Saugnapf von der Display Einheit.

    There is an adhesive strip all along the edge between the top and bottom of the phone. Is that just adhesive or is it wire of some sort?

    Larry Ingerling - Antwort

    @lingerling The adhesive strip was introduced on the iPhone 6s and 6s Plus (one model year later than what’s shown on this page). Guides specific to each model can be found here—be sure to use the correct one for your particular phone. And yes, just adhesive, no wires. ;)

    Jeff Suovanen - Antwort

  8. iPhone 6 Plus LCD und Touchscreen tauschen: Schritt 8, Bild 1 von 3 iPhone 6 Plus LCD und Touchscreen tauschen: Schritt 8, Bild 2 von 3 iPhone 6 Plus LCD und Touchscreen tauschen: Schritt 8, Bild 3 von 3
    • Nutze die Spitze des iPhones wie ein Scharnier und nimm das Displayende mit dem Home Button von der Rückseite ab.

    • Öffne das Display bis zu einem 90°-Winkel und lehne es gegen einen festen Gegenstand, um es beim Arbeiten in dieser Position zu halten.

    • Ein Gummiband könnte hilfreich sein, um es in dieser Position zu halten und sicherzustellen, dass die Displaykabel nicht beschädigt werden.

    • Als Trick kannst du eine ungeöffnete Getränkedose als Halterung verwenden.

    Be careful If we leave the screen connected and set it to 90 degrees, the speaker / sensor flex may break. With an opening of 60 degrees it is convenient to completely disconnect the screen. The headset's flex is short, and if we put it at 90º, it can break. Guiding me from the images of iFixit, I have broken two cables.


    Cuidado. Si dejamos la pantalla conectada y lo ponemos a 90 grados, el flex del altavoz/sensor puede romperse. Con una abertura de 60 grados es conveniente desconectar enteramente la pantalla. El flex del auricular es corto, y si lo ponemos en 90º , se puede romper. Guiándome de las imágenes de iFixit, se me han roto dos cables.

    txaukos - Antwort

    At 60º the display will block access to all the screws and the phone would be practically unserviceable, so I’m having trouble making sense of this comment. The cables on a factory original display are pretty tough and designed with enough slack that a 90º angle is no problem. Same with any decent aftermarket display.

    Jeff Suovanen - Antwort

    If you look at the enlarged image, you can see how the flex cable from the camera / speaker is in tension. This is my opinion. Sorry for my bad English

    Si usted se fija en la imagen ampliada, puede ver cómo el flex cable de la cámara/altavoz está en tensión. Esta es mi opinión.

    Perdón por mi mal inglés

    txaukos - Antwort

    your English isn’t the issue, it’s the proposed 60 degree opening space that doesn’t allow for the removal of the screws of the mounting plate where the connectors connect to the main pcb…

    if can make a recommendation here; it helps if the can is full and not refrigerated, the weight helps in keeping the phone where it should stay without adding additional tension to the ‘flex’ ribbon cable. it’s called flex for a reason people, if your breaking these the phones already been overheated too much, the cables become brittle and should also be replaced. i replaced my battery without disconnecting the screen, at 90 degrees with a rubber band around an empty beer can. pierced the orig. battery and caused sparks. albeit, i wasn’t in a hurry and it took me a good 30+ minutes, removal of the battery and stickers is by far the most challenging, especially when NOT disconnecting the screen…

    it’s not a race, take your time. move slowly but precisely with forethought and persistent force…

    circuitbender 477 - Antwort

    Werkt dit ook voor iPhone 7(plus)?

    Christina Pegtel - Antwort

    Werkt dit hetzelfde voor iPhone 7 (plus)?

    Christina Pegtel - Antwort

  9. iPhone 6 Plus LCD und Touchscreen tauschen: Schritt 9, Bild 1 von 2 iPhone 6 Plus LCD und Touchscreen tauschen: Schritt 9, Bild 2 von 2
    • Mehrere Clips am oberen Rand der Display Einheit bilden fast ein Scharnier, durch das das iPhone wie ein Buch aufgeklappt werden kann.

    • Achte während der Remontage darauf, die Clips direkt unter dem oberen Rand der Rückseite zu befestigen. Dann schiebe die Display Einheit nach oben, bis der obere Rand bündig mit dem der Rückseite ist.

    I would recommend protecting the screen once the display is free and the suction cup has been removed. This will help avoid any possibility of accidental scratching of the display crystal while the remaining steps are being performed. I used an inexpensive screen protector then removed it after reassembling and testing are complete.

    anthonyspampinato - Antwort

  10. iPhone 6 Plus LCD und Touchscreen tauschen: Schritt 10, Bild 1 von 1
    • Entferne die folgenden Kreuzschlitz-Schrauben von der Abdeckung des Akkuanschlusses:

    • Eine 2,3 mm #00 Kreuzschlitz-Schraube

    • Eine 3,1 mm #00 Kreuzschlitz-Schraube

    for the iPhone 6 Plus, all screws were Phillips #000

    Michael Adams - Antwort

    I had difficulty removing the 3.1mm (iPhone 6 Plus / Phillips #000); had to give it significant downward pressure to get it started.

    Allen Matheson - Antwort

    stripped the 2.3mm screw attempting to remove, had to use excessive force to successfully remove

    Matthew Gao - Antwort

    The Phillips bits provided in the kit would not engage the Phillips heads enough to loosen them. Luckily I had my own small screwdriver set that worked like a charm.

    David Davis - Antwort

    Same issue. Could not remove the screw. Dead in the water.

    Tiffany - Antwort

    Agree with above comments regarding the supplied Phillips bit. It is not the correct size.

    Use a Phillips #000.

    bobgottner - Antwort

    Phillips #000 is what’s included in the kit. As others mentioned above, firm downward pressure is key. The phone is not that delicate; just press hard and crank it.

    Jeff Suovanen -

    Is this step necessary ?\

    Asianay - Antwort

    @asianay0129 Yes, disconnecting the battery is necessary. You can sometimes get away with skipping it, at the risk of destroying something important and potentially bricking your phone. Not a wise gamble for the sake of skipping two screws.

    Jeff Suovanen - Antwort

  11. iPhone 6 Plus LCD und Touchscreen tauschen: Schritt 11, Bild 1 von 1
    • Entferne die Akkuverbindungsklemme aus Metall von dem iPhone.

    Was not able to remove the battery connector bracket as one of the cable connectors was glued/stuck to the underside. Instead moved the bracket out of the way to disconnect the battery. Care should be taken not to over bend/stretch the ribbon cable.

    dwtan - Antwort

    That may be just the foam connector adhering to the bracket. If you pull up gently and twist slightly it should separate.

    Evan Noronha -

    It was the foam connector, and it did twist free with a gentle pull

    Al Taylor - Antwort

  12. iPhone 6 Plus LCD und Touchscreen tauschen: Schritt 12, Bild 1 von 1
    • Heble den Akkustecker vorsichtig aus seinem Anschluss auf dem Logic Board. Das kannst du entweder mit einem sauberen Fingernagel oder mit einem Öffnungswerkzeug aus Kunststoff machen.

    • Achte darauf, dass du nur am Akkustecker hebelst und nicht an der Fassung auf dem Logic Board. Wenn du an der Fassung hebelst, kann der Anschluss brechen.

    you may consider placing a thin non-conductive item between the connector and the socket like a bit of rubber band to prevent any power flowing during this procedure

    Michael Adams - Antwort

    It was too close to other parts to pry up with either end of plastic tool. Finally used 1 tine of tweezer to lift edge. Came free easily

    Al Taylor - Antwort

    J’ai pris une loupe pour bien observer l’endroit où placer l’outil.

    Paul Briffaut - Antwort

    Magnification is key for many tasks and this is certainly one.

    Kenneth Gilbert - Antwort

    I couldn’t use the iFixit blue opening tool to pry that battery connector. I used the top of the black spudger near the hole where the 3.1mm screw was in step 9-10 to easily pry it open!

    Alyssa Sayuki - Antwort

    The blue plastic board breaker can easily cause damage here. Professionals would recommend using the human fingernail as the ideal tool for this job.

    Jessa Jones - Antwort

  13. iPhone 6 Plus LCD und Touchscreen tauschen: Schritt 13, Bild 1 von 1
    • Entferne die folgenden fünf Kreuzschlitz-Schrauben, mit denen die Kabelabdeckung der Display Einheit befestigt ist:

    • Drei 1,2 mm Schrauben

    • Eine 1,5 mm Schraube

    • Eine 2,9 mm Schraube

    • Versuche nicht, längere Schrauben in die rot markierten Schraubenlöcher einzuführen. Andernfalls kann es zu irreparablen Schäden am Logic Board kommen.

    There's an other panel with one screw in the middle.........

    Herbert - Antwort

    Sounds like you have an iPhone 6s Plus, rather than a 6 Plus. Be sure to use the correct guide! And make sure you’ve ordered the correct part, as they’re not cross-compatible.

    Jeff Suovanen -

    I _love_ the color coding of screws. I know this is a little OCD, but it would be incredibly useful if there were an 8.5 X 11 you could print with indicated homes for where to drop items from each step of disassembly. That is, in the box for step 9, little colored circles for where to place each screw type. As long as you don't jostle the paper, it would make it a lot easier to know exactly where you are in reassembly.

    cscarlson47shop - Antwort

    I have done the exact same thing. Created a sheet where each screw goes.

    Chris Murphy -

    I used the 000 bit from the ifixit 54 piece kit.

    hhandh - Antwort

    Actually you don’t need to do steps 12 to 18 if you attach the display panel to the iPhone box as shown in step 7 and handle your iPhone with care during the replacement. I didn’t disconnect the display panel mainly because the more you work on the interior of your phone the higher is the chance you break something.

    Dany Castillo - Antwort

    Since this guide is for DISPLAY replacement, I don’t see how you can skip the steps for disconnecting and removing the DISPLAY.

    Jim Bateman -

    That's what I was thinking.

    The Wizard - Antwort

    I skipped this series of steps too. I was very careful when removing the battery and never had an issue with the screen leaning back against the box that this battery shipped in. I even broke half of the third strip of adhesive but used a plastic card to slide under the battery and it slowly lifted out without applying heat.

    mark - Antwort

    I'm having trouble with one screw not wanting to come out. Any suggestions to keep from stripping the head and getting it?

    Patric - Antwort

    which screws are which sizes cause i ordered new ones and cant figure it out

    MONsterHEIT - Antwort

    I also did not see the need to remove the display assembly for this repair. However I did place a can of corn against the vertically positioned display and then secured the display to the can with a rubber band.

    whiteshephard - Antwort

    I recommend removing the display assembly, I didn’t and somehow damaged the home button cable. At least remove the cover to ease the tension on the cables.

    Steve Schlotter - Antwort

    I played around with different screwdrivers to get certain screws out. I made sure I wasn’t applying heavy pressure so I wouldn’t strip the head. Apple is crazy for doing this to us lol.

    Anyways invest in a magnetized mat to organize your screws. It was really difficult to keep things organized and still, especially with these tiny screws…

    Jeffrey Robinos - Antwort

    what happens if i forgot to put the ribbon cable shield back on? the phone is now working but i forgot to put the shield back on and i am missing 2 screws. can i leave the shield off?

    Fred ticoman. - Antwort

    @ticoman12 It’ll work without the shield, but the connectors may pop out unexpectedly.

    Jeff Suovanen -

    Just be really careful remembering which screw is which. I drew a quick sketch of the bracket, then put the screws in the relevant places. There’s no way I would have been able to figure them out otherwise - my eyes can’t see the difference between a 1.2 and 1.5mm screw!

    Paul Johnson - Antwort

    The most fiddly part of the job.

    Much easier if you put the screwdriver head on the screw and then insert it into the opening. The slight magnetism will hold it in place. Don’t fully tighten a screw until all the screws are in place. Much like installing lug nuts on a car.

    GPZ - Antwort

    I also skipped steps 12-18 as Danny had suggested. It made this repair quite easy, so thank you and others for suggesting this. I was also very careful to allow the battery to discharge before starting the process.

    Bruce Platt - Antwort

    I question whether Steps 12-18 (separating the display from the case) is actually necessary? The battery can be removed/replaced with the display connected (but standing upright, as displayed in Step 7.

    Leaving the display attached obviates the most difficult steps (re-connecting the various control ribbons — 3/4 of ‘em!

    I followed this manual completely and the repair was successful. But if I had this to do over, I’d leave the display connected.

    Dana Smith - Antwort

    I skipped the steps 12-18 as well and thank goodness I did so I won’t have to worry about issues with any of the cables.

    my panel is different from what is pictured anyway ‘cause I have one screw in the middle like what Herbert said on the first comment.

    Maria Filamor-Robinson - Antwort

    I realized too late just how handy the magnetic mat is that they have in their shop. So I organized the screws with a piece of clear packing tape. On the smooth side, use a sharpie to draw spacious circles with “R” “O” and “Y” inside each circle to represent the color coded screws and then use the sticky side to keep the screws in place. I found that using the tweezers to take them off the screwdriver helps you stick them head first to the tape better.

    Selena Castillo - Antwort

  14. iPhone 6 Plus LCD und Touchscreen tauschen: Schritt 14, Bild 1 von 1
    • Entferne die Kabelabdeckung der Display Einheit vom Logic Board.

  15. iPhone 6 Plus LCD und Touchscreen tauschen: Schritt 15, Bild 1 von 2 iPhone 6 Plus LCD und Touchscreen tauschen: Schritt 15, Bild 2 von 2
    • Passe bei den nächsten vier Schritten auf, dass du nur die Verbindungen der Kabel löst, und nicht die Anschlüsse auf dem Logic Board.

    • Halte die Display Einheit immer noch im 90°-Winkel, um die Frontkamera und das Sensorkabel zu lösen. Dazu kannst du deinen Fingernagel nutzen oder ein Öffnungswerkzeug aus Kunststoff.

    Why does the screen need to come off?

    Sterling Coffey (N0SSC) - Antwort

    Because the cables are delicate, and following steps are easier if phone halves are not flopping around together, especially for amateurs.

    Matthew Goheen - Antwort

    I don't know if anyone will see this but here it goes: for the life of me I can't get the front-facing camera and earpiece speaker connector to seat. Everything else went back together fine but this one connector will not go in. Sometimes it seems like it's in even though it doesn't really pop in and it'll kinda sit there for a sec and then it pops out.

    Any insight would be greatly appreciated, thank you

    Droopy Caledonia - Antwort

    Try starting at one end instead of in the middle. It's to easy to bend a connector and this way, I can get a safe start and go from there.

    Rongwey - Antwort

  16. iPhone 6 Plus LCD und Touchscreen tauschen: Schritt 16, Bild 1 von 2 iPhone 6 Plus LCD und Touchscreen tauschen: Schritt 16, Bild 2 von 2
    • Trenne den Anschluss vom Home Button Kabel.

  17. iPhone 6 Plus LCD und Touchscreen tauschen: Schritt 17, Bild 1 von 2 iPhone 6 Plus LCD und Touchscreen tauschen: Schritt 17, Bild 2 von 2
    • Vergewissere dich, dass der Akku abgeklemmt ist, bevor du das Kabel in diesem Schritt trennst oder wieder anschließt.

    • Nutze ein Öffnungswerkzeug aus Kunststoff, um das Touchscreen-Kabel zu lösen.

    • Beim Wiederzusammenbau kann sich das Displaykabel vom Anschluss lösen, dann würdest du entweder einen ganz schwarzen Bildschirm sehen oder weiße Linien im Display. In dem Fall kannst du dann einfach dieses Kabel wieder neu anschließen und dein iPhone zurücksetzen. Zurücksetzen geht am einfachsten indem du den Akkuanschluss trennst und dann wieder anschließt.

    The piece of advice about power cycling the phone by disconnecting and reconnecting the battery proved crucial to the success of my repair (camera and lens replacement). At first when charging the phone after closing it, I got a dark, blank screen with an intermittent buzzing noise. After re-opening the phone and making sure all cables had been properly reconnected, I ignored the advice to power cycle the phone. Still all I got was a dark, blank screen (and intermittent buzzing if charging t). Then I opened it a third time (leaving the screen connected and attached at a 90 degree angle) and I only disconnected and reconnected the battery. Voila! When I closed the phone and powered it up, I got the screen to light up!

    Gianni - Antwort

    how did you disconnect and reconnect the battery?

    Teresa Trevino - Antwort

    If you’ve been following the guide, you already disconnected it in this step. To reconnect it, just line up the connector and press it into place.

    Jeff Suovanen -

    After replacing the battery, the phone seems dead. I thought it just needed recharging so I left it charging all night. Still dead in the morning. Now I think it might be because the display data cable is off, and I should open the phone and check it. But the battery might be on full power in that case, and they don’t advice to open the phone when battery if full. What can I do?

    Ila Awasthi - Antwort

    The advice aims at avoiding battery fire. Just be careful.

    Katherine Williams - Antwort

  18. iPhone 6 Plus LCD und Touchscreen tauschen: Schritt 18, Bild 1 von 2 iPhone 6 Plus LCD und Touchscreen tauschen: Schritt 18, Bild 2 von 2
    • Zum Schluss musst du nur noch den Anschluss des Touchscreen-Kabels lösen.

    • Achte beim Wiederanschluss des Kabels darauf, nicht in der Mitte des Steckers zu drücken. Drücke erst an einem und dann am anderen Ende des Steckers. Wenn du in der Mitte drückst, kannst du den Anschluss und das Kabel des Touch Panels beschädigen.

    some images and guidance regarding reassembly would be helpful. You don't need to use the spudger to get them back on: fingers are better because there's a really subtle click you feel when you get them seated properly.

    cscarlson47shop - Antwort

    When you're reassembling, a note that this is the step where you should test for proper screen function would be really useful. First time I reassembled, I didn't seat something properly, got all the screws back together and then realized the screen wasn't functioning properly. Had to disassemble back down to step 14 and then re-reassemble.

    cscarlson47shop - Antwort

    I am having this issues right now! I have unplugged and plugged in these cables at least 20 times and each time I get white lines. I finally have it to where there are only 4 white lines and I am almost willing to live with it. Any suggestions?

    mattmay002 -

    Clean the screen connectors incase they are not making a clean connection

    Karen Jones - Antwort

    I'm having nightmares with the digitizer connector. Simply can't get it to work unless I'm applying some pressure on the connectors. Everything seems almost microscopically clean. Any suggestions friends?

    Henry A -

    could it be the replacement screen? test with your old screen and see if you have the same problem.

    Charles - Antwort

    To ++mattmay002++  Did you power cycle the phone? Check out the comments on the previous step for a how to.

    Robert Liles - Antwort

    I had issues with it too. When connecting this cable, make sure to rock finger side to side after connecting. It’s a wide connector so try to listen for 2 clicks on this one connector. That’s how I fixed mine

    Albert Einstein - Antwort

    Re-attaching this cable is the only tricky part to replacing the battery on my 6+. It had a bow on the middle that I had to flatten out before pressing the connector on with finger first on one edge and then on the other. I had white tire tracks on the screen and no touch screen until I connected it correctly. The front has to rest in just the right place on the back while attaching this thing so the cables aren’t strained the front doesn’t fall down. Small fingers would be a plus at this step.

    richard - Antwort

    Reseating these connectors on reassembly is definitely the most difficult part of this repair. It took me several attempts before the lowermost connector would seat properly and I did accidentally bend it slightly in the process. Fortunately I was able to get it straight again and get it to click in. The other three went in fine though and no lasting damage seems to have been done.

    Andy Gibbons - Antwort

    Another thing - These cables can become overlapped in the wrong way and make you think they are in a different order than they should be. Eg. it’s easy to mix up the ones from step 15 and 17. You can actually unravel the cables and re-layer them on top of each other in any order, so remember this! They look like they’re one solid mass but they’re not.

    domarius - Antwort

    I never removed the last digitizer connctor. I removed the first three connectors, left the screen propped at 90 deg tied to a box and removed the battery, there is minimal movement. In fact when I reattached the connectors, only the first and maybe second connector feels taut, so it’s necessary to only remove the first connector if you can be gentle with it. Less headache. And my guess why so many people had issues is that micro dust gets into the connectors and cause connection loss. You be surprised how little dust can cause havoc.

    darrcc - Antwort

    And forgot one thing, keep a can of air duster woth you to remove as must dust as you can see. A camera air blower will also do nice.

    darrcc - Antwort

    I haven’t removed my screen in past battery replacements, I found it easier. However, this time I followed the instructions because my old battery was very stuck, and I needed the screen gone to get the battery out…

    When I replaced the screen, at first it wouldn’t even boot/start up. (Yes, I inserted my own testing step, as someone here suggested, before final reassembly).

    The screen would just show a fuzzy image, and the board that all the cables attach to would heat up, then it would turn itself off. I tried reconnecting them carefully 3 times, and even made sure to get a little “click”, all to no avail.

    The final try, I used my fingernail to really press down on the back side of the digitizer cable. I heard more clicking, though I thought I might be tearing the cable too. With nothing left to lose, I continued across the back, and heard several more clicking/tearing sounds.

    This worked, and it booted after that. It still had white lines, but those faded away overnight.

    Morgan Giddings - Antwort

    About the digitizer connector: its flat cable is so short that the when I attempted to seat the next connector, its flat cable pressed on the digitizer cable, which can pull on the connector and dislodge it. That happened several times for me before success.

    Robert Bernard 27 Nov 19

    Robert H Bernard - Antwort

    Nous n’apercevons pas bien les nappes et l’ordre dans lesquelles elles doivent être replacer

    Patrick AZOULAY - Antwort

  19. iPhone 6 Plus LCD und Touchscreen tauschen: Schritt 19, Bild 1 von 1
    • Nimm die Display Einheit von der Rückseite ab.

    Never remove the screen without disconnecting the battery. It's possible the back light can be blown and that's a even more difficult repair. Always, ALWAYS, disconnect battery before repairing items. (Unless it's not possible.)

    Marvin Ballard - Antwort

    How do you disconnect the battery from the screen?

    Shamil Bhatti -

    The Step 11 disconnects the battery :)

    jeffxtechs - Antwort

    I think you mean Step 8 :)

    Jeff Suovanen -

    How do you disconnect the battery

    I tried it once and

    Brian - Antwort

    And what? I tried it once and here’s a million dollars?

    Oh I get it… they got him! :(


    domarius -

    When disassembling the iphone at this point note the cables, and there placement/orientation.

    GERARD SZAREK - Antwort

    Be really careful with the step after this. Do not commence until you have read all the comments. You need to get a good hold of the plastic strips preferably before they double over on themselves. You have to avoid puncturing the battery at all costs. Slowness and caution here will save you a lot of long term pain.

    Laura Houghton - Antwort

  20. iPhone 6 Plus LCD und Touchscreen tauschen, Ohrhörer-Lautsprecher: Schritt 20, Bild 1 von 1
    • Entferne folgende Kreuzschlitzschrauben, die die Halterung der oberen Komponenten befestigt:

    • Eine 1,5 mm Schraube

    • Zwei 2,3 mm Schrauben

    Nice move, which can stop the bracket from falling down.quite detailed instruction. but you should choice an excellent front facing camera and sensor before the replacement.

    William - Antwort

    Attempted this repair and my touch screen completely stopped working. Great walkthrough, but not sure what I did wrong in the repair to cause my issue.

    surfincubus86 - Antwort

    Hi I've had exactly the same problem, what was your solution to this? would be very helpful!

    Iona -

    I had the same issue. My screen quit working and I could feel heat coming through my phone at the earpiece. I took the phone apart again and realized that the data cable for the screen had come loose. When I reattached the data cable and starting working steps 12-18 backwards to replace the shield, as noted in the very last step, I see that youhave to keep the screen at an inclinewhen replacing the shield over the cables. Otherwise, you stretch the display data cable and it can come loose. My screen works fine now and there is no heat coming from my earpiece.

    Angela Hall -

    Just completed this repair. My front facing microphone next to the ear piece had gone bad causing siri to not hear me and front facing videos had no sound. Definitely reccomend getting replacement parts from ifixit. Have had good experiences with all their parts unlike many other suppliers on the internet. Hate to admit it (don't want them to raise prices) but even though you pay a little bit more, you save frustration not getting DOA parts from cheaper sources. All of ifixit's parts are top quality and they even pack them in anti-static packaging. That says alot. Thanks ifixit!

    sherwood7 - Antwort

    Great instructions save the later steps. The ear speaker piece having to bend 180 degrees for the installation needs more clarification.

    howchewdoin - Antwort

    After this repair, my screen quit working and I could feel heat coming through my phone at the earpiece. I took the phone apart again and realized that the data cable for the screen had come loose. When I reattached the data cable and starting working steps 12-18 backwards to replace the shield, as noted in the very last step, I see that you have to keep the screen at an incline when replacing the shield over the cables. Otherwise, you stretch the display data cable and it can come loose. My screen works fine now and there is no heat coming from my earpiece.

    Angela Hall - Antwort

    The middle screw, listed as a 2.3mm was actually a 2.9mm in my iPhone 6 Plus

    Matthew Goheen - Antwort

  21. iPhone 6 Plus LCD und Touchscreen tauschen: Schritt 21, Bild 1 von 1
    • Entferne die Abdeckung des Ohrhörer-Lautsprechers vom Display.

  22. iPhone 6 Plus LCD und Touchscreen tauschen: Schritt 22, Bild 1 von 1
    • Löse mit dem flachen Ende eines Spudgers die Kabel der Frontkamera und des Displays, und drücke sie leicht zur Seite.

  23. iPhone 6 Plus LCD und Touchscreen tauschen: Schritt 23, Bild 1 von 1
    • Greife mit einer Pinzette den Ohrhörer-Lautsprecher und entferne ihn von der Display Einheit.

  24. iPhone 6 Plus LCD und Touchscreen tauschen, Frontkamera und Sensoreinheit: Schritt 24, Bild 1 von 2 iPhone 6 Plus LCD und Touchscreen tauschen, Frontkamera und Sensoreinheit: Schritt 24, Bild 2 von 2
    • Heble vorsichtig mit der Spitze eines Spudgers die Sensorkabel-Einheit aus ihrer Vertiefung in der Displayeinheit.

    • Das Kabel ist leicht festgeklebt.

    Use a hair dryer to pre-heat and soften the adhesive. Otherwise, damage to the flex cable can occur.

    Rajat Sewal - Antwort

  25. iPhone 6 Plus LCD und Touchscreen tauschen: Schritt 25, Bild 1 von 2 iPhone 6 Plus LCD und Touchscreen tauschen: Schritt 25, Bild 2 von 2
    • Löse den Mikrofonteil der Komponenteneinheit aus Frontkamera und Sensorkabeln von der Displayeinheit.

    Das Mikrofonkabel ist mit einem Klebeband am Display besfestigt und muss durch anwärmen weich gemacht werden. Sonst besteht die Gefahr, dass beim Abziehen das Flachbandkabel beschädigt wird. Gruß Mike

    Mike - Antwort

    Bei meinem iPhone 6 Plus hörte das Kabel direkt vor der Gummiumrandung und nach dem Mikrofon auf. Auch das Ersatzteil ging nur bis dahin. Man musste also den Teil mit der Gummiumrandung nicht ablösen.

    gaby - Antwort

  26. iPhone 6 Plus LCD und Touchscreen tauschen: Schritt 26, Bild 1 von 1
    • Entferne die Komponenteneinheit mit der Frontkamera und dem Sensorkabel von der Display Einheit.

    • Ersatzeinheiten werden manchmal mit, manchmal ohne Lautsprechergitter ausgeliefert. Wenn es nicht dabei ist, musst du das alte aufheben und wiederverwenden. Du kannst es mit einem Haartrockner erwärmen und vorsichtig mit einer Pinzette ablösen.

  27. iPhone 6 Plus LCD und Touchscreen tauschen, Home Button Einheit: Schritt 27, Bild 1 von 1
    • Entferne die beiden 1,8 mm Kreuzschlitzschrauben, die die Home Button Abdeckung am Display befestigen.

    This guide is pointless, iPhone 6/6 plus home button is not replaceable, period.

    Tom Chai - Antwort

    Yes it is absolutely replaceable. You need to remember it is a encrypted security feature, so you'll need the apple ID or password to regain control again if replaced. That's the whole point to secure your data.

    Mike -

    Yes, the iPhone 6 and 6 Plus home buttons are replaceable. I do several replacements for customers and they work just fine with one exception. The fingerprint reader around the home button does not work after replacing the home button

    BrentTaylorBA - Antwort

    Hi Brent, I have a iPhone 6 plus with a shattered screen to repair and the home button is gone. You have said that you've been able to replace the home buttons successfully. I was wondering how you got past the error 53 problem when restoring it? Any suggestions or help would be greatly appreciated.

    arcadian212 -

    Error 53 was resolved by Apple with an iOS update, so fortunately this is no longer an issue! As others have stated, it's perfectly possible to replace the home button, but you will lose fingerprint sensor functionality (the original sensor is paired to your iPhone's logic board at the factory, and only Apple can pair a new one).

    Jeff Suovanen -

    Why does that make it pointless? The guide is geared towards screen replacement, with the intent of using the original home button and a new screen. It clearly states this. What about this guide is pointless? It's actually very helpful.

    abyss478 - Antwort

    Warning: The iphone 6 will brick after a restore if the home button is replaced. I agree with the other commenters that it is not a replaceable part because of this issue. If you try to restore the iPhone 6 after replacing the home button it will get stuck in recovery mode and give error 53 when a restore is attempted. I learned this the hard way! Please be careful and don't restore your phone if you do this repair.

    max - Antwort

    What did you do after your phone got stuck in recovery mode ?

    Lynn -

    I had an error 53 when trying to restore a iphone 6 plus.

    I bought a new heat shield with flex ribbon attached and installing that allowed me to get a restore complete.

    steve - Antwort

    I couldn't get my fingerprint reader to work after following this guide. I ended up taking the phone back apart and replacing the new screens' backing plate and the attached home button cable with the old, original one and now the fingerprint sensor works!

    fsharp320 - Antwort

    The little square rubber gaskets that cloak the mounting holes (little square nubs at the bottom of the picture in Step 19) for the Pentalobe Screws in Step 1 above had a tendency to fall off the screen. Further, if replacing the screen, these should also accompany the other items transferred to the new screen. This is just a small oversight I have seen from this repair guide, otherwise, smooth as silk.

    Justin - Antwort

    The connector seemed a bit raised after re-assembling, I noticed after pressing the bracket down on in preparation for screwing in. I don’t know if it’s normal for it to have a slightly raised feeling but it was noticeable. Enough to make me wonder if it’s too much pressure on it once it’s screwed together.

    domarius - Antwort

  28. iPhone 6 Plus LCD und Touchscreen tauschen: Schritt 28, Bild 1 von 1
    • Entferne die Home Button Abdeckung vom Display.

    buen día, cuando no me reconoce el touch id pero el boton si hace la función de botón ejemplo si me envía a home pero no reconoce el alcance fácil dos toques no reconoce el lector biométrico

    Yamir Maximino - Antwort

  29. iPhone 6 Plus LCD und Touchscreen tauschen: Schritt 29, Bild 1 von 2 iPhone 6 Plus LCD und Touchscreen tauschen: Schritt 29, Bild 2 von 2
    • Löse mit der Spitze eines Spudgers den Stecker des Home Buttons vom Anschluss auf dem Home Button Kabel.

    Will disabling and removing fingerprint passcode thru settings software wise prior to repair or starting the replacement, will this feature with a new replacement home button resolve the error 53 or the repairer need to use the original home button sensor with the correct fingerprint stored in the tiny small chip ? I have replaced a gsm iPhone 6S not plus screen making sure that not to tear off the sensor chip successfully repaired. -Joan

    JOAN E. VERGARA - Antwort

    Hi Joan! If I am understanding your question correctly, disabling the fingerprint passcode prior to repair WILL NOT result in Touch ID working after the repair. You should look at Jeff Suovanen's comment at the bottom, as he explains the two ways to keep Touch ID working. In order to keep Touch ID working, you will need to find a logic board that is paired with the home button and replace both of those components.

    Scott Havard -

    When reassembling this display connector, you must fold the new connector down into and against the plastic base in order to line up the sockets. The original connector cable is adhered to the screen, the replacement sticks straight out.

    Bret Hoffman - Antwort

    • Drücke vorsichtig einen Spudger unter das Kabel des Home Button Anschlusses.

    • Bewege den Spudger vorsichtig unter dem Kabel, um es vom Kleber zu lösen, der es auf dem Display befestigt.

    • Wenn sich das Kabel nicht einfach lösen lässt, wärme den Kleber leicht mit einem iOpener oder Fön an, um ihn zu lösen und versuche es erneut. Achte darauf, das Kabel nicht zu beschädigen.

    Es necesario calentar para que se desprenda de una forma comoda

    Yamir Maximino - Antwort

    i found using a needle works well too, as the fine point of the needle will be able to get under the adhesive and i can gently separate it.

    Charles - Antwort

    heat thoroughly with a hair dryer. (away from your work area so you don't blast your parts all over the place!) pops right off.

    edwardlyman - Antwort

    • Die Gummidichtung um den Home Button ist sehr dünn und zerreißt leicht.

    • Erwärme den Kleber, mit dem die Dichtung um den Home Button befestigt ist, leicht (mit einem iOpener, einem Heißluftgebläse oder einem Haartrockner) .

    • Drücke den Home Button vorsichtig von der Vorderseite der Displayeinheit aus mit der Fingerkuppe nach oben. Drücke fest und gleichmäßig, bis sich die Gummidichtung um den Home Button langsam vom Frontpanel löst.

  30. iPhone 6 Plus LCD und Touchscreen tauschen: Schritt 32, Bild 1 von 2 iPhone 6 Plus LCD und Touchscreen tauschen: Schritt 32, Bild 2 von 2
    • Löse den Home Button vorsichtig mit der Spudgerspitze ganz vom Frontpanel ab.

    The little rubber gasket seems to be a moisture seal. It isn’t glued down but over time it seals itself to the display. Pushing the spudger around underneath simply breaks the bond between the two surfaces. Be sure to do it carefully so as not to tear it.

    bichmgnt - Antwort

  31. iPhone 6 Plus LCD und Touchscreen tauschen: Schritt 33, Bild 1 von 1
    • Entferne die Home Button Einheit vom Display.

    So this fix is hardware only? Do I need to disable the touch ID feature before removal and wWhat do I do next to get the touch ID feature to function?

    Dasteufelhund - Antwort

    After removing the home button, remove the two black rubber bumpers from the ‘Pentalobe Screw’ mount brackets and transfer them to the new screen, this helps secure the home button in place and screw tension.

    James_P - Antwort

  32. iPhone 6 Plus LCD und Touchscreen tauschen, LCD und Touchscreen: Schritt 34, Bild 1 von 2 iPhone 6 Plus LCD und Touchscreen tauschen, LCD und Touchscreen: Schritt 34, Bild 2 von 2
    • Entferne die beiden 1,7 mm Kreuzschlitzschrauben (eine am oberen und eine am unteren Rand) die das LCD Abschirmblech am Display befestigen.

  33. iPhone 6 Plus LCD und Touchscreen tauschen: Schritt 35, Bild 1 von 2 iPhone 6 Plus LCD und Touchscreen tauschen: Schritt 35, Bild 2 von 2
    • Entferne je drei 1,3 mm Kreuzschlitzschrauben am Rand des LCD Abschirmblechs (insgesamt sechs).

    The required tools list specifies a phillips #000 screwdriver, but this section indicates #00 sized screws. Can some confirm for me the actual size of the screws? If they are #00, I see the screwdrivers for this size come in 1.5 mm and 2.5 mm versions. Which should I get?

    Sidney Burton - Antwort

    If you’re using iFixit bits, either the #000 or the #00 will work fine here. Bit sizes are not standardized across manufacturers, so if you’re using tools from another vendor you’ll just have to test as you go.

    Jeff Suovanen -

  34. iPhone 6 Plus LCD und Touchscreen tauschen: Schritt 36, Bild 1 von 2 iPhone 6 Plus LCD und Touchscreen tauschen: Schritt 36, Bild 2 von 2
    • In diesem Schritt musst du das eine Ende des Home Button Kabels (im zweiten Bild in rot hervorgehoben) lösen, welches mit starkem Kleber an der Display befestigt ist. Wir empfehlen, hierfür einen iOpener zu verwenden, und den unteren Rand der Display direkt über dem Home Button zu erhitzen.

    you can remove this by using the smallest flat screw driver bit you have. Using the supplied picture as reference start at the lower left hand corner and push gently between the connector ribbon and the case. The glue easily separated for me.

    GERARD SZAREK - Antwort

    Do not peel off the ribbon cable!

    You should take off small rectangular metal plate on which connector is. The glue is between the metal and plastic body.

    Use a sharp needle at the lower left corner.

    peoplewide - Antwort

  35. iPhone 6 Plus LCD und Touchscreen tauschen: Schritt 37, Bild 1 von 3 iPhone 6 Plus LCD und Touchscreen tauschen: Schritt 37, Bild 2 von 3 iPhone 6 Plus LCD und Touchscreen tauschen: Schritt 37, Bild 3 von 3
    • Hebe das Ende beim Ohrhörer Lautsprecher für wenige Millimeter an, ohne es komplett zu entfernen.

    • Hebe vorsichtig auch das andere Ende (nahe dem Home Button) an, um das Kabel des Home Buttons von der Display Einheit zu lösen.

    • Sei extrem vorsichtig beim Lösen des Home Button Kabels. Es ist ein sehr dünnes Kabel, das leicht reißen kann. Wenn du mehr als leichten Widerstand fühlst empfehlen wir, den iOpener erneut zu erhitzen und den Kleber zu erwärmen.

    • Entferne das LCD Abschirmblech vom Display

    • Übrig bleibt das Display.


Arbeite die Schritte in umgekehrter Reihenfolge ab, um dein Gerät wieder zusammenzubauen.

222 weitere Nutzer:innen haben diese Anleitung absolviert.

Besonderer Dank geht an diese Übersetzer:innen:

en de


Diese Übersetzer:innen helfen uns, die Welt zu reparieren! Wie kann ich mithelfen?
Hier starten ›

11 Kommentare

I know this is a old guide but i have a question. My iphone was screen broken and i change it with a original complete iphone screen, the home button works fine but the touch id dont work. I change the home button to the one that i have in the broken screen and still the touch id dont work. What can i do to fix the touch id?

Juanjo Checo - Antwort

Help! The home button cable attached to the metal front panel ripped a little as I was gently using my fingers to lift it off the screen. Now the home button doesn't work. Did I ruin the phone or is it possible to get a front panel?

Merry Hansen - Antwort

I recently purchased this iFixit kit for my iPhone 6 Plus replacement of my screen that was cracked. I followed the instructions above, and my phone won't turn on. There is a part in to the right of the battery, just below the screen connections, that is really hot. After I noticed it wouldn't turn on, even after plugging it in, I took it back apart, and reseated the connections again. It still doesn't work. I will not purchase this kit again.

Dustin Klumb - Antwort

Bought this recently and I must say that I'm a little bit disappointed:

- the screen doesn't fit as before, you can feel a rough edge - I tried 4 times to put it correctly watching many video tutorials and I had the same result so I assume it's because it's not an original screen

- the colours are not the same anymore, looks like the saturation is on a lower setting - can't see the bright colours anymore

Overall I would rate this part 6 out of 10.

andrewbuta - Antwort

Followed this guide to the letter about 1 week ago. Happy to say its very accurate and my iphone is working 100%

Most difficult and time consuming part was re-inserting the front-facing camera and sensor cable assembly (Step 25) and also removing the home button cable (step 36)

morjo21 - Antwort

I’ve just completed this guide successfully using replacement parts I’ve ordered with ifixit in Europe. To my own surprise, everything is working: both cameras, home button, fingerprint scanner and id. Just great. I didn’t have the iSclack tool so I just used the suction cup. Also, I had to use a hair dryer instead of the iOpener tool, and it worked great even with the home button cable, just go gentle and give the heat some time to soften up the adhesive. Thanks for the great guide.

Georg Federmann - Antwort

Is this for if it don’t light up? because mine won’t come on.

Hunter Rowland - Antwort

My iPhone was entered water and I took it to engineer and he said water has spoil the panel, he said I should order for new panel ,does it work if I change the panel.

Adeniran tope David - Antwort

You did not talk about removing eye lens casing. This is the most pain when trying to put back the bracket back.

Chathura Gunawardana - Antwort

you guys rock - thank you!

benmansfield.mach1 - Antwort

I just said F it and use a Windows phone that I can mod myself

mxcombust - Antwort

Kommentar hinzufügen


Letzte 24 Stunden: 7

Letzte 7 Tage: 25

Letzte 30 Tage: 204

Insgesamt: 175,550