Zum Hauptinhalt wechseln

iPhone 6 Plus Lautstärkeregler und Stummschalter ersetzen

Was du brauchst

  1. iPhone 6 Plus Lautstärkeregler und Stummschalter ersetzen, Pentalobe Schrauben: Schritt 1, Bild 1 von 1
    • Entlade dein iPhone auf unter 25%, bevor du es demontierst. Eine geladene Lithium-Ionen-Batterie kann Feuer fangen und/oder explodieren, wenn man sie aus Versehen ansticht.

    • Schalte dein iPhone ab, bevor du mit der Demontage beginnst.

    • Entferne die beiden 3,6 mm P2 Pentalobe Schrauben neben dem Lightning Connector.

    I prefer to remove the SIM card as the very first step since it's safer to do so while the phone is fully assembled.

    estebanfallasf - Antwort

    I stripped one of the two screws - at a dead stop.

    Margaret Patterson - Antwort

    Before you even start: get the iOpener or hairdryer out. You’ll need it

    GPZ - Antwort

    If a lightning connector won’t provide a charge or needs to be wiggled carefully to provide a charge, power off the device, then try using precision tweezers to scrape the innermost wall of the lightning jack in a pinching motion to check for lint buildup. Pocket lint or other debris can accumulate inside the jack, compacting each time a cable is inserted. This can prevent a lightning cable from seating fully. Clearing the lint may restore functionality without replacing the part.

    Andrew Dolan - Antwort

    A few hints:

    * heating up the phone works great. I used a heating pad that you put in the microwave to heat sports injuries.

    * also, I made a sheet to help you keep track of the screws as you remove them. Print out the page, then place double sided tape below each color-coded listing of screws, and stick the screws to the tape as you disassemble. This helps prevent losing the screws and keeps track of what screws are what for easier reassembly. https://drive.google.com/file/d/1pLSvKvB...

    Paul Faulstich - Antwort

    Additional hints, for anyone who needs them:

    * stick the screws to the tape in the same positions as they are shown in the guide. This will make it easier to identify them during reassembly.

    * if the screws get mixed together, the ‘mm’ (millimetre, millimeter) measurements given in the guide can be used to identify them. Compare the lengths of the threaded shafts to each other to determine which screw is which.

    Friendly Advice -

  2. iPhone 6 Plus Lautstärkeregler und Stummschalter ersetzen, Anweisungen für die Anti-Clamp: Schritt 2, Bild 1 von 3 iPhone 6 Plus Lautstärkeregler und Stummschalter ersetzen, Anweisungen für die Anti-Clamp: Schritt 2, Bild 2 von 3 iPhone 6 Plus Lautstärkeregler und Stummschalter ersetzen, Anweisungen für die Anti-Clamp: Schritt 2, Bild 3 von 3
    • In den nächsten beiden Schritten wird die Verwendung der Anti-Clamp gezeigt, ein Werkzeug, das wir entwickelt haben, um den Öffnungsvorgang zu erleichtern. Wenn du die Anti-Clamp nicht verwendest, überspringe die ersten drei Schritte, um eine alternative Methode zu finden.

    • Eine ausführliche Anleitung zur Verwendung der Anti-Clamp findest du in dieser Anleitung.

    • Ziehe den blauen Griff nach hinten, um die Arme der Anti-Clamp zu entriegeln.

    • Schiebe die Arme entweder über die linke oder rechte Kante deines iPhones.

    • Positioniere die Saugheber nahe an der Unterkante des iPhones direkt über dem Home Button - einen auf der Vorderseite und einen auf der Rückseite.

    • Drücke die Saugheber zusammen, um sie auf der gewünschten Stelle zu befestigen.

    • Wenn du feststellst, dass die Oberfläche deines iPhones für die Anti-Clamp zu rutschig ist, kannst du mit Klebeband eine griffigere Oberfläche schaffen.

  3. iPhone 6 Plus Lautstärkeregler und Stummschalter ersetzen: Schritt 3, Bild 1 von 3 iPhone 6 Plus Lautstärkeregler und Stummschalter ersetzen: Schritt 3, Bild 2 von 3 iPhone 6 Plus Lautstärkeregler und Stummschalter ersetzen: Schritt 3, Bild 3 von 3
    • Ziehe den blauen Griff nach vorne, um die Arme zu verriegeln.

    • Drehe den Griff im Uhrzeigersinn um 360 Grad oder bis die Suagheber anfangen, sich zu dehnen.

    • Achte darauf, dass die Saugheber zueinander ausgerichtet bleiben. Wenn sie zu verrutschen beginnen, löse die Saugheber etwas und richte die Arme neu aus.

    • Setze ein Plektrum oder ein Öffnungswerkzeug unter das Display ein, wenn die Anti-Klemme einen ausreichend großen Spalt erzeugt hat.

    • Wenn die Anti-Clamp keinen ausreichend großen Abstand bildet, drehe den Griff um eine Vierteldrehung.

    • Drehe den Griff nicht mehr als eine Vierteldrehung auf einmal und warte zwischen den einzelnen Umdrehungen ein paar Sekunden. Lasse die Anti-Clamp und die Zeit die Arbeit für dich machen.

    • Überspringe die nächsten drei Schritte.

    Use clear nontextured tape place that over the phone screen. Refer to any guide that addresses replacing a shattered screen

    Abigail Cherry - Antwort

    I know it's tough with cracked glass. You just need enough to get in a plstic pry tool or guitar pick. Then you can pry it apart. Just be patient, I cannot stress that enough; the electronics are very, very small and fragile.

    Mike - Antwort

  4. iPhone 6 Plus Lautstärkeregler und Stummschalter ersetzen, Display Einheit: Schritt 4, Bild 1 von 1
    • Benutze einen einzelnen Saugheber, um die Display-Einheit anzuheben:

    • Drücke einen Saugheber auf das Display, direkt über (aber nicht auf) den Home Button.

    • Drücke den Saugheber gut auf der Scheibe fest, damit er sicher haften bleibt.

    • Wenn die Scheibe stark gesplittert ist, haftet der Saugheber möglicherweise nicht gut. Klebe eine Lage von durchsichtigem Paketband darüber, damit er besser festhält. Du kannst auch anstelle eines Saughebers sehr starkes Klebeband verwenden. Eine weitere Möglichkeit ist, den Saugheber mit Sekundenkleber zu befestigen.

    Avec la ventouse, l’ouverture est brutale, tout s’est déclipsé d’un seul coup. Faire attention.

    Paul Briffaut - Antwort

    English Please!

    tom mozeleski -

    With the sucker, the opening is brutal, everything was cleared at once. Pay attention. (Paul’s comment translated by Google)

    Steve Schlotter - Antwort

    May need to burp the sticker before it sticks. Need to let the air out. Once Idid that, no problem. Except it was still hard to get the cover to start up.

    Patricia Tucker - Antwort

    Don’t waste your time with the suction cup - it doesn’t work! insert the blade of a box cutter just below the lower screen edge below the home button and gently pry just enough to start cracking the seal.

    Stephen Smith - Antwort

  5. iPhone 6 Plus Lautstärkeregler und Stummschalter ersetzen: Schritt 5, Bild 1 von 1
    • Ziehe an dem Saugnapf während du das iPhone mit der anderen Hand festhältst, um die Displayeinheit etwas von der Rückseite anzuheben.

    • Nimm dir Zeit und wende gleichbleibend feste Kraft an. Die Displayeinheit sitzt sehr viel passgenauer im Gerät als viele andere Teile.

    • Benutze ein Plastik Opening Tool, um vorsichtig die Rückseite nach unten zu drücken, weg von der Display Einheit, während du das Display weiter mit dem Saugnapf nach oben ziehst.

    • Mehrere Clips befestigen die Display Einheit im Gehäuse, weshalb du vielleicht den Saugnapf und ein Plastik Opening Tool brauchst, um die Displayeinheit von der Rückseite zu lösen.

    Be extra careful here. If you don’t take your time, your front panel may jerk back on you, causing you to overextend and break the front camera/mic flex cable; happened to me. Slowly peel back the front panel, opening it no more than 90º.

    Thomas - Antwort

    watch out for the left side of the phone the adhesive bunches up around the inner clips, i didn’t realize it and the upper left of my screen cracked pretty bad. But this guide is awesome follow every direction to the letter

    Aaron Fitzpatrick - Antwort

    Note: this comment is written for the iPhone 6 Plus, but may also apply to other models of iPhone.

    Disassembly:

    The clips in the rear case attach to small slotted shapes under the edges of the display assembly, and these attachment points alternate from one side to the other. Moving from bottom to top, gently pulling the rear case away at these points will help to separate the two halves without using too much force.

    Reassembly:

    Ensure that the plastic clips along the top edge of the front panel (shown in step 8) are fitted properly inside the rear case, then gently press the display assembly into the rear case at these points, moving from top to bottom. There may be a small click sound as the clips in the rear case engage with the slots on the display assembly, and the rear case should fit flush with the edges of the display assembly.

    Friendly Advice - Antwort

    This was challenging. For me, the suction cup could only create a tiny bit of motion and at first, no actual gap at all. You might have to pull the suction cup away from the base a few times just to loosen things up a tiny bit. Eventually, I got my fingernail in, and then after a few minutes got the plastic tool in.

    Also, use the plastic tool to gently pry along the sides of the phone once there’s light there. I was afraid of using too much leverage and breaking the screen as per the other comments, but starting at the bottom and then going around the sides slowly worked for me.

    FixingMyiPhone - Antwort

  6. iPhone 6 Plus Lautstärkeregler und Stummschalter ersetzen: Schritt 6, Bild 1 von 2 iPhone 6 Plus Lautstärkeregler und Stummschalter ersetzen: Schritt 6, Bild 2 von 2
    • Ziehe an der Plastiknoppe, um das Vakuum des Saugnapfes zu lösen.

    • Entferne den Saugnapf von der Display Einheit.

    There is an adhesive strip all along the edge between the top and bottom of the phone. Is that just adhesive or is it wire of some sort?

    Larry Ingerling - Antwort

    @lingerling The adhesive strip was introduced on the iPhone 6s and 6s Plus (one model year later than what’s shown on this page). Guides specific to each model can be found here—be sure to use the correct one for your particular phone. And yes, just adhesive, no wires. ;)

    Jeff Suovanen - Antwort

  7. iPhone 6 Plus Lautstärkeregler und Stummschalter ersetzen: Schritt 7, Bild 1 von 3 iPhone 6 Plus Lautstärkeregler und Stummschalter ersetzen: Schritt 7, Bild 2 von 3 iPhone 6 Plus Lautstärkeregler und Stummschalter ersetzen: Schritt 7, Bild 3 von 3
    • Nutze die Spitze des iPhones wie ein Scharnier und nimm das Displayende mit dem Home Button von der Rückseite ab.

    • Öffne das Display bis zu einem 90°-Winkel und lehne es gegen einen festen Gegenstand, um es beim Arbeiten in dieser Position zu halten.

    • Ein Gummiband könnte hilfreich sein, um es in dieser Position zu halten und sicherzustellen, dass die Displaykabel nicht beschädigt werden.

    • Als Trick kannst du eine ungeöffnete Getränkedose als Halterung verwenden.

    Be careful If we leave the screen connected and set it to 90 degrees, the speaker / sensor flex may break. With an opening of 60 degrees it is convenient to completely disconnect the screen. The headset's flex is short, and if we put it at 90º, it can break. Guiding me from the images of iFixit, I have broken two cables.

    Español:

    Cuidado. Si dejamos la pantalla conectada y lo ponemos a 90 grados, el flex del altavoz/sensor puede romperse. Con una abertura de 60 grados es conveniente desconectar enteramente la pantalla. El flex del auricular es corto, y si lo ponemos en 90º , se puede romper. Guiándome de las imágenes de iFixit, se me han roto dos cables.

    txaukos - Antwort

    At 60º the display will block access to all the screws and the phone would be practically unserviceable, so I’m having trouble making sense of this comment. The cables on a factory original display are pretty tough and designed with enough slack that a 90º angle is no problem. Same with any decent aftermarket display.

    Jeff Suovanen - Antwort

    If you look at the enlarged image, you can see how the flex cable from the camera / speaker is in tension. This is my opinion. Sorry for my bad English

    Si usted se fija en la imagen ampliada, puede ver cómo el flex cable de la cámara/altavoz está en tensión. Esta es mi opinión.

    Perdón por mi mal inglés

    txaukos - Antwort

    your English isn’t the issue, it’s the proposed 60 degree opening space that doesn’t allow for the removal of the screws of the mounting plate where the connectors connect to the main pcb…

    if can make a recommendation here; it helps if the can is full and not refrigerated, the weight helps in keeping the phone where it should stay without adding additional tension to the ‘flex’ ribbon cable. it’s called flex for a reason people, if your breaking these the phones already been overheated too much, the cables become brittle and should also be replaced. i replaced my battery without disconnecting the screen, at 90 degrees with a rubber band around an empty beer can. pierced the orig. battery and caused sparks. albeit, i wasn’t in a hurry and it took me a good 30+ minutes, removal of the battery and stickers is by far the most challenging, especially when NOT disconnecting the screen…

    it’s not a race, take your time. move slowly but precisely with forethought and persistent force…

    circuitbender 477 - Antwort

    Werkt dit ook voor iPhone 7(plus)?

    Christina Pegtel - Antwort

    Werkt dit hetzelfde voor iPhone 7 (plus)?

    Christina Pegtel - Antwort

  8. iPhone 6 Plus Lautstärkeregler und Stummschalter ersetzen: Schritt 8, Bild 1 von 2 iPhone 6 Plus Lautstärkeregler und Stummschalter ersetzen: Schritt 8, Bild 2 von 2
    • Mehrere Clips am oberen Rand der Display Einheit bilden fast ein Scharnier, durch das das iPhone wie ein Buch aufgeklappt werden kann.

    • Achte während der Remontage darauf, die Clips direkt unter dem oberen Rand der Rückseite zu befestigen. Dann schiebe die Display Einheit nach oben, bis der obere Rand bündig mit dem der Rückseite ist.

    I would recommend protecting the screen once the display is free and the suction cup has been removed. This will help avoid any possibility of accidental scratching of the display crystal while the remaining steps are being performed. I used an inexpensive screen protector then removed it after reassembling and testing are complete.

    anthonyspampinato - Antwort

  9. iPhone 6 Plus Lautstärkeregler und Stummschalter ersetzen: Schritt 9, Bild 1 von 1
    • Entferne die folgenden Kreuzschlitz-Schrauben von der Abdeckung des Akkuanschlusses:

    • Eine 2,3 mm #00 Kreuzschlitz-Schraube

    • Eine 3,1 mm #00 Kreuzschlitz-Schraube

    for the iPhone 6 Plus, all screws were Phillips #000

    Michael Adams - Antwort

    I had difficulty removing the 3.1mm (iPhone 6 Plus / Phillips #000); had to give it significant downward pressure to get it started.

    Allen Matheson - Antwort

    stripped the 2.3mm screw attempting to remove, had to use excessive force to successfully remove

    Matthew Gao - Antwort

    The Phillips bits provided in the kit would not engage the Phillips heads enough to loosen them. Luckily I had my own small screwdriver set that worked like a charm.

    David Davis - Antwort

    Same issue. Could not remove the screw. Dead in the water.

    Tiffany - Antwort

    Agree with above comments regarding the supplied Phillips bit. It is not the correct size.

    Use a Phillips #000.

    bobgottner - Antwort

    Phillips #000 is what’s included in the kit. As others mentioned above, firm downward pressure is key. The phone is not that delicate; just press hard and crank it.

    Jeff Suovanen -

    Is this step necessary ?\

    Asianay - Antwort

    @asianay0129 Yes, disconnecting the battery is necessary. You can sometimes get away with skipping it, at the risk of destroying something important and potentially bricking your phone. Not a wise gamble for the sake of skipping two screws.

    Jeff Suovanen - Antwort

  10. iPhone 6 Plus Lautstärkeregler und Stummschalter ersetzen: Schritt 10, Bild 1 von 1
    • Entferne die Akkuverbindungsklemme aus Metall von dem iPhone.

    Was not able to remove the battery connector bracket as one of the cable connectors was glued/stuck to the underside. Instead moved the bracket out of the way to disconnect the battery. Care should be taken not to over bend/stretch the ribbon cable.

    dwtan - Antwort

    That may be just the foam connector adhering to the bracket. If you pull up gently and twist slightly it should separate.

    Evan Noronha -

    It was the foam connector, and it did twist free with a gentle pull

    Al Taylor - Antwort

  11. iPhone 6 Plus Lautstärkeregler und Stummschalter ersetzen: Schritt 11, Bild 1 von 1
    • Heble den Akkustecker vorsichtig aus seinem Anschluss auf dem Logic Board. Das kannst du entweder mit einem sauberen Fingernagel oder mit einem Öffnungswerkzeug aus Kunststoff machen.

    • Achte darauf, dass du nur am Akkustecker hebelst und nicht an der Fassung auf dem Logic Board. Wenn du an der Fassung hebelst, kann der Anschluss brechen.

    you may consider placing a thin non-conductive item between the connector and the socket like a bit of rubber band to prevent any power flowing during this procedure

    Michael Adams - Antwort

    It was too close to other parts to pry up with either end of plastic tool. Finally used 1 tine of tweezer to lift edge. Came free easily

    Al Taylor - Antwort

    J’ai pris une loupe pour bien observer l’endroit où placer l’outil.

    Paul Briffaut - Antwort

    Magnification is key for many tasks and this is certainly one.

    Kenneth Gilbert - Antwort

    I couldn’t use the iFixit blue opening tool to pry that battery connector. I used the top of the black spudger near the hole where the 3.1mm screw was in step 9-10 to easily pry it open!

    Alyssa Sayuki - Antwort

    The blue plastic board breaker can easily cause damage here. Professionals would recommend using the human fingernail as the ideal tool for this job.

    Jessa Jones - Antwort

  12. iPhone 6 Plus Lautstärkeregler und Stummschalter ersetzen: Schritt 12, Bild 1 von 1
    • Entferne die folgenden fünf Kreuzschlitz-Schrauben, mit denen die Kabelabdeckung der Display Einheit befestigt ist:

    • Drei 1,2 mm Schrauben

    • Eine 1,5 mm Schraube

    • Eine 2,9 mm Schraube

    • Versuche nicht, längere Schrauben in die rot markierten Schraubenlöcher einzuführen. Andernfalls kann es zu irreparablen Schäden am Logic Board kommen.

    There's an other panel with one screw in the middle.........

    Herbert - Antwort

    Sounds like you have an iPhone 6s Plus, rather than a 6 Plus. Be sure to use the correct guide! And make sure you’ve ordered the correct part, as they’re not cross-compatible.

    Jeff Suovanen -

    I _love_ the color coding of screws. I know this is a little OCD, but it would be incredibly useful if there were an 8.5 X 11 you could print with indicated homes for where to drop items from each step of disassembly. That is, in the box for step 9, little colored circles for where to place each screw type. As long as you don't jostle the paper, it would make it a lot easier to know exactly where you are in reassembly.

    cscarlson47shop - Antwort

    I have done the exact same thing. Created a sheet where each screw goes.

    Chris Murphy -

    I used the 000 bit from the ifixit 54 piece kit.

    hhandh - Antwort

    Actually you don’t need to do steps 12 to 18 if you attach the display panel to the iPhone box as shown in step 7 and handle your iPhone with care during the replacement. I didn’t disconnect the display panel mainly because the more you work on the interior of your phone the higher is the chance you break something.

    Dany Castillo - Antwort

    Since this guide is for DISPLAY replacement, I don’t see how you can skip the steps for disconnecting and removing the DISPLAY.

    Jim Bateman -

    That's what I was thinking.

    The Wizard - Antwort

    I skipped this series of steps too. I was very careful when removing the battery and never had an issue with the screen leaning back against the box that this battery shipped in. I even broke half of the third strip of adhesive but used a plastic card to slide under the battery and it slowly lifted out without applying heat.

    mark - Antwort

    I'm having trouble with one screw not wanting to come out. Any suggestions to keep from stripping the head and getting it?

    Patric - Antwort

    which screws are which sizes cause i ordered new ones and cant figure it out

    MONsterHEIT - Antwort

    I also did not see the need to remove the display assembly for this repair. However I did place a can of corn against the vertically positioned display and then secured the display to the can with a rubber band.

    whiteshephard - Antwort

    I recommend removing the display assembly, I didn’t and somehow damaged the home button cable. At least remove the cover to ease the tension on the cables.

    Steve Schlotter - Antwort

    I played around with different screwdrivers to get certain screws out. I made sure I wasn’t applying heavy pressure so I wouldn’t strip the head. Apple is crazy for doing this to us lol.

    Anyways invest in a magnetized mat to organize your screws. It was really difficult to keep things organized and still, especially with these tiny screws…

    Jeffrey Robinos - Antwort

    what happens if i forgot to put the ribbon cable shield back on? the phone is now working but i forgot to put the shield back on and i am missing 2 screws. can i leave the shield off?

    Fred ticoman. - Antwort

    @ticoman12 It’ll work without the shield, but the connectors may pop out unexpectedly.

    Jeff Suovanen -

    Just be really careful remembering which screw is which. I drew a quick sketch of the bracket, then put the screws in the relevant places. There’s no way I would have been able to figure them out otherwise - my eyes can’t see the difference between a 1.2 and 1.5mm screw!

    Paul Johnson - Antwort

    The most fiddly part of the job.

    Much easier if you put the screwdriver head on the screw and then insert it into the opening. The slight magnetism will hold it in place. Don’t fully tighten a screw until all the screws are in place. Much like installing lug nuts on a car.

    GPZ - Antwort

    I also skipped steps 12-18 as Danny had suggested. It made this repair quite easy, so thank you and others for suggesting this. I was also very careful to allow the battery to discharge before starting the process.

    Bruce Platt - Antwort

    I question whether Steps 12-18 (separating the display from the case) is actually necessary? The battery can be removed/replaced with the display connected (but standing upright, as displayed in Step 7.

    Leaving the display attached obviates the most difficult steps (re-connecting the various control ribbons — 3/4 of ‘em!

    I followed this manual completely and the repair was successful. But if I had this to do over, I’d leave the display connected.

    Dana Smith - Antwort

    I skipped the steps 12-18 as well and thank goodness I did so I won’t have to worry about issues with any of the cables.

    my panel is different from what is pictured anyway ‘cause I have one screw in the middle like what Herbert said on the first comment.

    Maria Filamor-Robinson - Antwort

    I realized too late just how handy the magnetic mat is that they have in their shop. So I organized the screws with a piece of clear packing tape. On the smooth side, use a sharpie to draw spacious circles with “R” “O” and “Y” inside each circle to represent the color coded screws and then use the sticky side to keep the screws in place. I found that using the tweezers to take them off the screwdriver helps you stick them head first to the tape better.

    Selena Castillo - Antwort

  13. iPhone 6 Plus Lautstärkeregler und Stummschalter ersetzen: Schritt 13, Bild 1 von 1
    • Entferne die Kabelabdeckung der Display Einheit vom Logic Board.

  14. iPhone 6 Plus Lautstärkeregler und Stummschalter ersetzen: Schritt 14, Bild 1 von 2 iPhone 6 Plus Lautstärkeregler und Stummschalter ersetzen: Schritt 14, Bild 2 von 2
    • Passe bei den nächsten vier Schritten auf, dass du nur die Verbindungen der Kabel löst, und nicht die Anschlüsse auf dem Logic Board.

    • Halte die Display Einheit immer noch im 90°-Winkel, um die Frontkamera und das Sensorkabel zu lösen. Dazu kannst du deinen Fingernagel nutzen oder ein Öffnungswerkzeug aus Kunststoff.

    Why does the screen need to come off?

    Sterling Coffey (N0SSC) - Antwort

    Because the cables are delicate, and following steps are easier if phone halves are not flopping around together, especially for amateurs.

    Matthew Goheen - Antwort

    I don't know if anyone will see this but here it goes: for the life of me I can't get the front-facing camera and earpiece speaker connector to seat. Everything else went back together fine but this one connector will not go in. Sometimes it seems like it's in even though it doesn't really pop in and it'll kinda sit there for a sec and then it pops out.

    Any insight would be greatly appreciated, thank you

    Droopy Caledonia - Antwort

    Try starting at one end instead of in the middle. It's to easy to bend a connector and this way, I can get a safe start and go from there.

    Rongwey - Antwort

  15. iPhone 6 Plus Lautstärkeregler und Stummschalter ersetzen: Schritt 15, Bild 1 von 2 iPhone 6 Plus Lautstärkeregler und Stummschalter ersetzen: Schritt 15, Bild 2 von 2
    • Trenne den Anschluss vom Home Button Kabel.

  16. iPhone 6 Plus Lautstärkeregler und Stummschalter ersetzen: Schritt 16, Bild 1 von 2 iPhone 6 Plus Lautstärkeregler und Stummschalter ersetzen: Schritt 16, Bild 2 von 2
    • Vergewissere dich, dass der Akku abgeklemmt ist, bevor du das Kabel in diesem Schritt trennst oder wieder anschließt.

    • Nutze ein Öffnungswerkzeug aus Kunststoff, um das Touchscreen-Kabel zu lösen.

    • Beim Wiederzusammenbau kann sich das Displaykabel vom Anschluss lösen, dann würdest du entweder einen ganz schwarzen Bildschirm sehen oder weiße Linien im Display. In dem Fall kannst du dann einfach dieses Kabel wieder neu anschließen und dein iPhone zurücksetzen. Zurücksetzen geht am einfachsten indem du den Akkuanschluss trennst und dann wieder anschließt.

    The piece of advice about power cycling the phone by disconnecting and reconnecting the battery proved crucial to the success of my repair (camera and lens replacement). At first when charging the phone after closing it, I got a dark, blank screen with an intermittent buzzing noise. After re-opening the phone and making sure all cables had been properly reconnected, I ignored the advice to power cycle the phone. Still all I got was a dark, blank screen (and intermittent buzzing if charging t). Then I opened it a third time (leaving the screen connected and attached at a 90 degree angle) and I only disconnected and reconnected the battery. Voila! When I closed the phone and powered it up, I got the screen to light up!

    Gianni - Antwort

    how did you disconnect and reconnect the battery?

    Teresa Trevino - Antwort

    If you’ve been following the guide, you already disconnected it in this step. To reconnect it, just line up the connector and press it into place.

    Jeff Suovanen -

    After replacing the battery, the phone seems dead. I thought it just needed recharging so I left it charging all night. Still dead in the morning. Now I think it might be because the display data cable is off, and I should open the phone and check it. But the battery might be on full power in that case, and they don’t advice to open the phone when battery if full. What can I do?

    Ila Awasthi - Antwort

    The advice aims at avoiding battery fire. Just be careful.

    Katherine Williams - Antwort

  17. iPhone 6 Plus Lautstärkeregler und Stummschalter ersetzen: Schritt 17, Bild 1 von 2 iPhone 6 Plus Lautstärkeregler und Stummschalter ersetzen: Schritt 17, Bild 2 von 2
    • Zum Schluss musst du nur noch den Anschluss des Touchscreen-Kabels lösen.

    • Achte beim Wiederanschluss des Kabels darauf, nicht in der Mitte des Steckers zu drücken. Drücke erst an einem und dann am anderen Ende des Steckers. Wenn du in der Mitte drückst, kannst du den Anschluss und das Kabel des Touch Panels beschädigen.

    some images and guidance regarding reassembly would be helpful. You don't need to use the spudger to get them back on: fingers are better because there's a really subtle click you feel when you get them seated properly.

    cscarlson47shop - Antwort

    When you're reassembling, a note that this is the step where you should test for proper screen function would be really useful. First time I reassembled, I didn't seat something properly, got all the screws back together and then realized the screen wasn't functioning properly. Had to disassemble back down to step 14 and then re-reassemble.

    cscarlson47shop - Antwort

    I am having this issues right now! I have unplugged and plugged in these cables at least 20 times and each time I get white lines. I finally have it to where there are only 4 white lines and I am almost willing to live with it. Any suggestions?

    mattmay002 -

    Clean the screen connectors incase they are not making a clean connection

    Karen Jones - Antwort

    I'm having nightmares with the digitizer connector. Simply can't get it to work unless I'm applying some pressure on the connectors. Everything seems almost microscopically clean. Any suggestions friends?

    Henry A -

    could it be the replacement screen? test with your old screen and see if you have the same problem.

    Charles - Antwort

    To ++mattmay002++  Did you power cycle the phone? Check out the comments on the previous step for a how to.

    Robert Liles - Antwort

    I had issues with it too. When connecting this cable, make sure to rock finger side to side after connecting. It’s a wide connector so try to listen for 2 clicks on this one connector. That’s how I fixed mine

    Albert Einstein - Antwort

    Re-attaching this cable is the only tricky part to replacing the battery on my 6+. It had a bow on the middle that I had to flatten out before pressing the connector on with finger first on one edge and then on the other. I had white tire tracks on the screen and no touch screen until I connected it correctly. The front has to rest in just the right place on the back while attaching this thing so the cables aren’t strained the front doesn’t fall down. Small fingers would be a plus at this step.

    richard - Antwort

    Reseating these connectors on reassembly is definitely the most difficult part of this repair. It took me several attempts before the lowermost connector would seat properly and I did accidentally bend it slightly in the process. Fortunately I was able to get it straight again and get it to click in. The other three went in fine though and no lasting damage seems to have been done.

    Andy Gibbons - Antwort

    Another thing - These cables can become overlapped in the wrong way and make you think they are in a different order than they should be. Eg. it’s easy to mix up the ones from step 15 and 17. You can actually unravel the cables and re-layer them on top of each other in any order, so remember this! They look like they’re one solid mass but they’re not.

    domarius - Antwort

    I never removed the last digitizer connctor. I removed the first three connectors, left the screen propped at 90 deg tied to a box and removed the battery, there is minimal movement. In fact when I reattached the connectors, only the first and maybe second connector feels taut, so it’s necessary to only remove the first connector if you can be gentle with it. Less headache. And my guess why so many people had issues is that micro dust gets into the connectors and cause connection loss. You be surprised how little dust can cause havoc.

    darrcc - Antwort

    And forgot one thing, keep a can of air duster woth you to remove as must dust as you can see. A camera air blower will also do nice.

    darrcc - Antwort

    I haven’t removed my screen in past battery replacements, I found it easier. However, this time I followed the instructions because my old battery was very stuck, and I needed the screen gone to get the battery out…

    When I replaced the screen, at first it wouldn’t even boot/start up. (Yes, I inserted my own testing step, as someone here suggested, before final reassembly).

    The screen would just show a fuzzy image, and the board that all the cables attach to would heat up, then it would turn itself off. I tried reconnecting them carefully 3 times, and even made sure to get a little “click”, all to no avail.

    The final try, I used my fingernail to really press down on the back side of the digitizer cable. I heard more clicking, though I thought I might be tearing the cable too. With nothing left to lose, I continued across the back, and heard several more clicking/tearing sounds.

    This worked, and it booted after that. It still had white lines, but those faded away overnight.

    Morgan Giddings - Antwort

    About the digitizer connector: its flat cable is so short that the when I attempted to seat the next connector, its flat cable pressed on the digitizer cable, which can pull on the connector and dislodge it. That happened several times for me before success.

    Robert Bernard 27 Nov 19

    Robert H Bernard - Antwort

    Nous n’apercevons pas bien les nappes et l’ordre dans lesquelles elles doivent être replacer

    Patrick AZOULAY - Antwort

  18. iPhone 6 Plus Lautstärkeregler und Stummschalter ersetzen: Schritt 18, Bild 1 von 1
    • Nimm die Display Einheit von der Rückseite ab.

    Never remove the screen without disconnecting the battery. It's possible the back light can be blown and that's a even more difficult repair. Always, ALWAYS, disconnect battery before repairing items. (Unless it's not possible.)

    Marvin Ballard - Antwort

    How do you disconnect the battery from the screen?

    Shamil Bhatti -

    The Step 11 disconnects the battery :)

    jeffxtechs - Antwort

    I think you mean Step 8 :)

    Jeff Suovanen -

    How do you disconnect the battery

    I tried it once and

    Brian - Antwort

    And what? I tried it once and here’s a million dollars?

    Oh I get it… they got him! :(

    https://www.youtube.com/watch?v=UlznqpBg...

    domarius -

    When disassembling the iphone at this point note the cables, and there placement/orientation.

    GERARD SZAREK - Antwort

    Be really careful with the step after this. Do not commence until you have read all the comments. You need to get a good hold of the plastic strips preferably before they double over on themselves. You have to avoid puncturing the battery at all costs. Slowness and caution here will save you a lot of long term pain.

    Laura Houghton - Antwort

  19. iPhone 6 Plus Lautstärkeregler und Stummschalter ersetzen, Akku: Schritt 19, Bild 1 von 1
    • Ziehe den ersten Akku-Klebestreifen, ausgehend von der unteren rechten Ecke des Akkus, nach unten weg.

    • Benutze deine Finger oder eine stumpfe Pinzette und sei extra vorsichtig wenn du in der Nähe des Akkus arbeitest – einen Li-Ionen Akku aufzustechen kann gefährliche Chemikalien freisetzen und einen Brand verursachen.

    Ça été pour moi la partie la plus difficile du démontage de l’iPhone, j’ai cassé les 2 bandes parce que je ne me suis pas bien appliqué pour les décoller avec la pince. Pour m’en sortir,. j’ai tordu la batterie avec les outils de manière à faire apparaître les bandes adhésives pour les enlever sans problème.

    Paul Briffaut - Antwort

    Translation from Google:

    It was for me the most difficult part of the disassembly of the iPhone, I broke the two bands because I did not apply well to take off with the clamp. To get out of it ,. I twisted the battery with the tools so that the adhesive strips appeared to remove them without any problem.

    Ken - Antwort

    Slowly roll the pulled-out adhesive onto itself as you progress, this makes it easier to gauge how much stretch you need to exert on the remaining adhesive, as well as to gain enough grip to hold the adhesive properly. I also nearly tore off the middle one, it’s not due to my rough but because the battery’s black tape (at the area where these adhesive tabs are) caught onto the white adhesive, this must be the reason why most people’s tore off. Mine nearly tore off, so i slow rolled the pulled-out adhesive to catch back the adhesive, and then it’s roll and pull as per normal. With that I took equal precaution for the last one on the left, and it also was caught by the black tape, but since i know it this time, i slowly pulled it free of the black tape first before continuing the roll snd pull. 100% works. Trust me. My battery is slightly warm as i deliberately let it run for a while before i started the disassembly. I doubt it contributes much to the removal but no harm.

    darrcc - Antwort

    It's easier if you grasp the full width of the adhesive strip, straight across it, before starting to pull. That way the force is applied gently and evenly to the whole strip. I used watchmaker's forceps because they precisely pull up the adhesive tab, and easily squeeze the whole width of the strip—since it's critical to apply the pulling force evenly across the strip. Tug gently and twist the forceps to take up the slack, pulling just a few millimeters at a time. I learned this the hard way. My center strip snapped pretty quick because I didn't have a good, even grasp of it.

    For heat, I put a cup of raw white rice in a clean sock, knotted the open end, and microwaved it for 2 minutes. When it was cool enough to handle, I flattened it on the table and lay the phone upon it. That gave off enough gentle steady heat that I could pry up the battery without much bending, locate the adhesive end, and successfully wind it up with the forceps. I think I would use the hot rice-bed from the start next time. —Kw

    Katherine Williams - Antwort

  20. iPhone 6 Plus Lautstärkeregler und Stummschalter ersetzen: Schritt 20, Bild 1 von 2 iPhone 6 Plus Lautstärkeregler und Stummschalter ersetzen: Schritt 20, Bild 2 von 2
    • Versuche dabei die Streifen möglichst glatt und knitterfrei zu halten. Verknitterte Streifen verkleben leicht und können reißen, anstatt sauber herauszukommen.

    • Ziehe einen Akku-Klebestreifen ganz langsam weg vom Akku zum unterem Rand des iPhones hin.

    • Der Streifen sollte sich erst dehnen, bevor du fester daran ziehst. Wenn du merkst, dass er sich nicht mehr dehnt, dann lasse nach, sonst reißt er.

    • Ziehe in einem möglichst flachen Winkel, ohne dass der Streifen an einem der Bauteile im unteren Bereich des Smartphones hängen bleibt.

    • Drücke beim Herausziehen des Streifens nicht auf den Akku.

    • Der Streifen wird sich auf ein Vielfaches seiner ursprünglichen Länge ausdehnen. Ziehe ihn langsam solange heraus, bis er sich loslöst und unter dem Akku herausrutscht.

    • Wenn die Zuglasche am Akku beim Ausbau reißt, dann fasse mit den Fingern oder einer stumpfen Pinzette am Reststück an und ziehe weiter heraus.

    • Wenn ein Klebestreifen unter dem Akku reißt und nicht mehr erreicht werden kann, entferne so viel du kannst und mache folgendermaßen weiter.

    I found this much easier than when I did it on a 5S. Not sure if the adhesive strips are different, but I also left the phone on a radiator for a few minutes to help warm the glue. All three then pulled straight out of the phone in one go.

    James - Antwort

    I set my phone on a microfiber cloth on a plate that I had warmed (warm to the touch and that I could hold with my bare hands) in the microwave prior to this step. All 3 strips came off from the bottom and without any trouble.

    armitagd - Antwort

    Excellent tip, thanks.

    vanshdx10 - Antwort

    absolutely impossible unless you heat it. Thank You armitagd, that did the trick.

    chris - Antwort

    All three of mine tore off immediately, I had warmed the phone up too. A bit of a struggle with the tweezers and card method, the battery bent and leaked. Came out okay.

    John Blanchard - Antwort

    I recommend preheating the case before trying to remove each adhesive tape. Also, try wrapping the tape around a pencil as you pull and stretch the tape. I think that such gives a more even pull across the tape than by using one’s fingers.

    GPZ - Antwort

    I even didn’t find an adhesive in my phone, I had to use hairdryer to heat the battery, then remove it gently using the blue plastic and couple of plastic cards

    Mohammed Jitarayah - Antwort

    I can’t stress enough how important it is to preheat the case as others have mentioned. GPZ’s recommendation using a pencil is also pure gold - get enough initial purchase on the adhesive strip so that you can pull it taut and then place your pencil. From there, roll and tag alternately, keeping tension on it so that the adhesive doesn’t wrinkle in the process of removal.

    Jesse Espe - Antwort

    Heating probably works but I slowly pulled out an inch or so and then started rolling it onto my screwdriver. Then I slowly rolled the screwdriver which gave me a good grip and I could go slowly. Took more than 5 min but it got easier and easier. Believe me, getting the battery out using the alternative is very hard, and dangerously easy to penetrate the battery and start a small flame thrower (voice of experience).

    Thomas Hayes - Antwort

  21. iPhone 6 Plus Lautstärkeregler und Stummschalter ersetzen: Schritt 21, Bild 1 von 2 iPhone 6 Plus Lautstärkeregler und Stummschalter ersetzen: Schritt 21, Bild 2 von 2
    • Ziehe den zweiten Akku-Klebestreifen an der anderen Seite des Akkus zurück.

    • Ziehe wieder vorsichtig und langsam am Streifen, er wird sich dehnen, bis er zwischen dem Akku und der Rückseite herauskommt.

    • Mache solange weiter, bis der Streifen sich komplett vom Akku löst. Wenn er reißt, dann versuche das Reststück zu fassen und weiterzuziehen, oder fahre mit den folgenden Schritten fort

    This strip broke almost immediately with the first pull. I changed the battery on two iPhone 6 Plus’s. Impossible for me to retrieve broken ends. I moved on to the middle strip with no issue. I then used the blue opening tool to pry the battery up along the lower right edge of the battery (BE CAREFUL!). Once the battery is leveraged up enough to put the tip of the tweezers on the broken strip, grab a piece of the strip and pull it to a point where the removal process can continue as prescribed.

    whiteshephard - Antwort

    Pulling the strip around the corner did not work for me - it broke. I then pulled the middle strip straight out with no issues and the remaining left strip also straight without no problem. I don’t recommend pulling the side strips around the corner of the battery

    Swenja - Antwort

  22. iPhone 6 Plus Lautstärkeregler und Stummschalter ersetzen: Schritt 22, Bild 1 von 3 iPhone 6 Plus Lautstärkeregler und Stummschalter ersetzen: Schritt 22, Bild 2 von 3 iPhone 6 Plus Lautstärkeregler und Stummschalter ersetzen: Schritt 22, Bild 3 von 3
    • Löse die letzte Zuglasche von der Unterkante des Akkus ab. Ziehe dann die Zuglasche behutsam nach oben vom Akku weg, so dass der Klebestreifen langsam zwischen Akku und Rückgehäude herauskommt.

    • Lege beim Herausziehen des letzten Streifens die Hand über den Akku, damit der Akku nicht herausgeschleudert werden kann.

    • Ziehe so lange, bis du den Streifen komplett aus dem iPhone entfernen kannst.

    • Wenn du alle drei Klebestreifen erfolgreich entfernt hast, fahre mit Schritt 24 fort. Falls einer der Streifen gerissen ist und Reste unter dem Akku kleben, gib einige Tropfen von hochkonzentriertem Isopropylalkohol (mehr als 90%ig) an der Stelle, wo der Klebestreifen gerissen ist, unter die Kante des Akkus.

    • Lasse den Alkohol etwa eine Minute lang wirken, damit der Klebestreifen geschwächt wird. Hebe dann den Akku mit dem flachen Ende des Spudgers vorsichtig hoch.

    • Versuche nicht, den Akku mit Gewalt herauszuhebeln. Tröpfle mehr Alkohol hinein, falls das nötig ist, um den Kleber zu schwächen. Verforme niemals den Akku und stich ihn nicht an.

    • Heble nicht gegen das Logic Board, du könntest sonst das iPhone dauerhaft beschädigen. Heble nicht im Bereich zwischen der oberen Kante des Akkus und dem Lautstärkeregler (-) ein, sonst riskierst du, das Kabel zu den Lautstärketasten zu beschädigen, das direkt unter dem Akku in das Rückgehäuse geklebt ist.

    • Im folgenden Schritt werden noch Alternativmethoden zum Ablösen des Akkus gezeigt.

    I don’t know why the instructions didn’t mention this, but I pulled it to the left and back, like the previous strip, rather than straight back, to avoid snapping.

    domarius - Antwort

    Pull the adhesive strips at a 45° angle up away from the back or the strip will catch on the bottom board and will tear and break. If it starts to tear, , see if you can grab a spot after the ear and keep pulling. These things are super thin and fragile. Go sloooow when you pull the strips. You are going to pull them a long way, so be patient.

    Ok, so you broke one. Or two. Or all three. Forget the alcohol. Lay your phone face down on a towel and heat it with a hair dryer for two minutes. Flip it over carefully as it will be hot. Insert a plastic spudger under the bottom edge and carefully push/slide it under the battery toward to top of the phone along the strip(s) that are still stuck. DO NOT PRY. You may have to heat it again if it gets hard to push. BE CAREFUL. The battery will bend a bit, but don’t bend it excessively or poke it as it can catch fire when exposed to air. Eventually the battery will pop free. Remove the stuck adhesive and wipe it a bit with alcohol and let it dry.

    Sheldon Carpenter - Antwort

  23. iPhone 6 Plus Lautstärkeregler und Stummschalter ersetzen, Alternativmethoden zum Ablösen eines festgeklebten Akkus: Schritt 23, Bild 1 von 1
    • Wenn der Akku immer noch festklebt, dann kannst du einen heißen iOpener oder einen Haartrockner benutzen, um damit die Gehäuserückseite direkt hinter dem Akku zu erwärmen. Sie sollte so heiß sein, dass du sie kaum anfassen kannst.

    • Hebe den Akku dann vorsichtig mit einem Öffnungswerkzeug aus Kunststoff hoch.

    • Wenn das iPhone zu heiß, wird kann sich der Akku entzünden.

    • Alternativ kannst du auch ein Stück Zahnseide benutzen, um den Akku von der Gehäuserückseite zu lösen. Eine stabilere Alternative ist eine Gitarrensaite, zum Beispiel eine 0,009 E Saite aus einem 12er Set.

    • Fädle die Zahnseide oder die Gitarrensaite unter ein Ende des Akkus und ziehe sie dann wie ein Säge hin und her, um den Kleber zu lösen.

    Hat leider alles nicht geklappt! Musste mit einer Karte und einer Seite sehr lange fummeln und da sich die Folie vom Akku zu sehr mit dem gehäuse verbunden hat. Dadurch hat sie sich gelöst und durch das erwärmen leider auch nicht wirklich besser.

    Jess Sass - Antwort

    Translation from Google:

    Unfortunately, everything did not work out! Had to fumble with a card and a page for a long time and because the film from the battery has too much connected to the housing. As a result, she has solved and by warming unfortunately not really better.

    Ken -

    This step was very difficult as the adhesive strips snapped on me and I had to use a card to make the strips come out by siding the plastic card on the strips as thought I was trying to cut a very thin slice of cheese. (NOTE: DO NOT USE ANYTHING METAL when attempting this method) I actually tried using a metal spudger while trying to remove the adhesive strips and punctured the old battery slightly enough to cause smoke.

    Bryan - Antwort

    iBreak-it: caught the wifi antenna connector when using a guitar string to work the extremely stubborn battery adhesive strips off. Now I need a new wifi antenna. What next?

    Dale Williams - Antwort

    Lay your phone face down on a towel and heat it with a hair dryer for two minutes. Flip it over carefully as it will be hot. Insert a plastic spudger under the bottom edge and carefully push/slide it under the battery toward to top of the phone along the strip(s) that are still stuck. DO NOT PRY. You may have to heat it again if it gets hard to push. BE CAREFUL. The battery will bend a bit, but don’t bend it excessively or poke it as it can catch fire when exposed to air. Eventually the battery will pop free. Remove the stuck adhesive and wipe it a bit with alcohol and let it dry.

    Sheldon Carpenter - Antwort

  24. iPhone 6 Plus Lautstärkeregler und Stummschalter ersetzen: Schritt 24, Bild 1 von 1
    • Nimm den Akku aus dem iPhone.

    • Sollte dein Ersatzakku in einer Plastikhülle geliefert werden, entferne zuerst die Plastikhülle vom Akku, indem du die Hülle vom Flachbandkabel abziehst, und setze erst dann den Akku ein.

    • Wenn noch Reste vom Alkohol im Smartphone verblieben sind, dann wische sie sorgfältig weg oder lasse das Gehäuse gut austrocknen.

    • Stecke vor dem Festkleben des neuen Akkus den Akkustecker vorläufig in den Anschluss auf dem Logic Board ein. Dadurch nimmt der Akku die richtige Position in seiner Vertiefung ein.

    • Klebe den Akku fest, löse den Stecker wieder ab und fahre mit dem Zusammenbau fort.

    • Wenn an deinem neuen Akku noch keine Klebestreifen dran sind, dann folge dieser Anleitung, um die Klebestreifen korrekt anzubringen.

    • Führe nach dem Austausch einen Hard Reset durch. Dies verhindert einige Probleme und vereinfacht die möglicherweise dennoch anfallende Fehlersuche.

    Once again, ifixit comes through! I bought the battery and the repair kit and the new battery installed and charging. My only hitch was that the three adhesive strips all broke when I pulled on them. I had to heat the bottom of the phone to separate the battery. It was a small moment of panic, but it just required a bit more patience. Thanks for all you do!

    jamesg - Antwort

    Awesome procedure! Thanks. iPhone 6plus working great. Make sure you have quality tools. Thanks again.

    Leo Lambert - Antwort

    Everything went well enough but, I replaced the battery last month and after a while the phone started going into an on-off cycle. It only happens intermittently. At first it would do it only once and stop. Now it does it, still intermittently, but when it happens it keeps cycling on and off. It even does it when it’s charging. If I let it sit, while charging, after several hours it stops doing it again.

    Larry Ingerling - Antwort

    The battery kit didn’t come with adhesives. It seems that I’m not the only one to mention it .

    Nat Turner - Antwort

    Hi there! The battery kit does come with replacement adhesive along with all the tools needed to complete the repair. The part-only battery does not include adhesive, it needs to be purchased separately!

    Sam Goldheart -

    Almost blew up the battery with alot of holes, im traumatized. In the end i did by force and trew it 10 meters away while i were outside.

    Milan - Antwort

    i turned on my phone and the screen is all stripes :(

    Emily M. Curran - Antwort

    Sounds like either the display cable isn't properly connected or it’s been damaged. If all else fails, send it to a professional.

    Rongwey -

    The Ifixit battery comes with new adhesive strips already attached to the battery. Suggest that it’s best to leave the protective acetate over the strips until AFTER the new battery is re-connected and the connector cover is reinstalled (2 screws). Then its easy to remove the acetate cover from the adhesive strips and locate the battery.

    If the battery is stuck in (with the adhesive strips BEFORE the connector is correctly installed it is impossible to adjust the position of the battery to align the connector.

    Dana Smith - Antwort

    My screen doesn’t even show up anything when charging but it makes the sound thought.

    Osvaldo G - Antwort

  25. iPhone 6 Plus Lautstärkeregler und Stummschalter ersetzen, Antenneneinheit: Schritt 25, Bild 1 von 1
    • Entferne die folgenden Schrauben, die die Antennenklammer im Rückgehäuse befestigen:

    • Eine 1,5 mm Kreuzschlitz #00 Schraube

    • Eine 2,8 mm Kreuzschlitz #00 Schraube

  26. iPhone 6 Plus Lautstärkeregler und Stummschalter ersetzen: Schritt 26, Bild 1 von 1
    • Entferne die Antennenklammer mit einer Pinzette aus dem iPhone.

  27. iPhone 6 Plus Lautstärkeregler und Stummschalter ersetzen: Schritt 27, Bild 1 von 1
    • Löse mit einem Plastik-Öffnungswerkzeug den Anschluss der Antenne vom Logic Board.

  28. iPhone 6 Plus Lautstärkeregler und Stummschalter ersetzen: Schritt 28, Bild 1 von 2 iPhone 6 Plus Lautstärkeregler und Stummschalter ersetzen: Schritt 28, Bild 2 von 2
    • Greife den Anschluss der Antenne mit einer Pinzette und hebe ihn vorsichtig vom Halteclip auf dem Logic Board.

  29. iPhone 6 Plus Lautstärkeregler und Stummschalter ersetzen: Schritt 29, Bild 1 von 2 iPhone 6 Plus Lautstärkeregler und Stummschalter ersetzen: Schritt 29, Bild 2 von 2
    • Die beiden Anschlüsse sind vielleicht mit einem Klebestreifen verbunden. Wenn dies der Fall ist lassen sie sich vielleicht nur gemeinsam lösen.

    • Löse die Kabel des Power Buttons und der Lautstärkeregler von ihren Anschlüssen auf dem Logic Board.

  30. iPhone 6 Plus Lautstärkeregler und Stummschalter ersetzen: Schritt 30, Bild 1 von 1
    • Entferne die folgenden Schrauben, die die Mobilfunkantenne im Rückgehäuse befestigen:

    • Eine 2,8 mm Kreuzschlitz #00 Schraube

    • Zwei 1,6 mm Kreuzschlitz #00 Schrauben

  31. iPhone 6 Plus Lautstärkeregler und Stummschalter ersetzen: Schritt 31, Bild 1 von 2 iPhone 6 Plus Lautstärkeregler und Stummschalter ersetzen: Schritt 31, Bild 2 von 2
    • Hebe die Mobilfunkantenne mit einer Pinzette aus dem iPhone.

    • Achte während des Zusammenbaus darauf, die kleine Unterlegscheibe in der oberen rechten Ecke der Antenneneinheit zu platzieren.

  32. iPhone 6 Plus Lautstärkeregler und Stummschalter ersetzen, Lautstärkeregler- und Stummschalterkabel: Schritt 32, Bild 1 von 2 iPhone 6 Plus Lautstärkeregler und Stummschalter ersetzen, Lautstärkeregler- und Stummschalterkabel: Schritt 32, Bild 2 von 2
    • Löse mit einer Pinzette den einzelnen Klebestreifen, der die Kabelanschlüsse des Power Buttons und des Lautstärkereglers/Stummschalters befestigt.

  33. iPhone 6 Plus Lautstärkeregler und Stummschalter ersetzen: Schritt 33, Bild 1 von 1
    • Entferne die folgenden Schrauben, die das Lautstärkeregler- und Stummschalterkabel im Rückgehäuse befestigen:

    • Zwei 2,0 mm Kreuzschlitz #00 Schrauben

    • Eine 2,5 mm Kreuzschlitz #00 Schraube

  34. iPhone 6 Plus Lautstärkeregler und Stummschalter ersetzen: Schritt 34, Bild 1 von 3 iPhone 6 Plus Lautstärkeregler und Stummschalter ersetzen: Schritt 34, Bild 2 von 3 iPhone 6 Plus Lautstärkeregler und Stummschalter ersetzen: Schritt 34, Bild 3 von 3
    • Greife das Lautstärkeregler- und Stummschalterkabel mit einer Pinzette.

    • Ziehe vorsichtig das Lautstärkeregler- und Stummschalterkabel aus dem Rückgehäuse.

    • Sei vorsichtig. Das Kabel ist mit mildem Klebstoff im Rückgehäuse befestigt.

    Hallo

    vielleicht kannst du mir helfen ich habe bei meinem iPhone X den stummschalten aus gebaut und erneuert jetzt kriege ich es nicht mehr zusammen Bzw der stumm Schalter wird beim festschrauben sehr schwergäng bis fest woran liegt das bin am verzweifeln

    defilippo - Antwort

  35. iPhone 6 Plus Lautstärkeregler und Stummschalter ersetzen, Lautstärkeregler und Stummschalter: Schritt 35, Bild 1 von 2 iPhone 6 Plus Lautstärkeregler und Stummschalter ersetzen, Lautstärkeregler und Stummschalter: Schritt 35, Bild 2 von 2
    • Drücke mit der Spitze eines Spudgers die Lautstärkeregler und den Stummschalter aus ihrer Vertiefung im Rückgehäuse.

  36. iPhone 6 Plus Lautstärkeregler und Stummschalter ersetzen: Schritt 36, Bild 1 von 2 iPhone 6 Plus Lautstärkeregler und Stummschalter ersetzen: Schritt 36, Bild 2 von 2
    • Greife vorsichtig mit einer Pinzette sowohl den oberen als auch den unteren Lautstärkeregler und entferne beide aus dem iPhone.

Abschluss

Arbeite die Schritte in umgekehrter Reihenfolge ab, um dein Gerät wieder zusammenzubauen.

35 weitere Nutzer:innen haben diese Anleitung absolviert.

Besonderer Dank geht an diese Übersetzer:innen:

en de

100%

Diese Übersetzer:innen helfen uns, die Welt zu reparieren! Wie kann ich mithelfen?
Hier starten ›

Ein Kommentar

Excelente sigan asi

Henry García - Antwort

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 1

Letzte 7 Tage: 10

Letzte 30 Tage: 76

Insgesamt: 60,727