Zum Hauptinhalt wechseln

iPhone 6 SIM Auswurfhebel ersetzen

Was du brauchst

  1. iPhone 6 SIM Auswurfhebel ersetzen, Pentalobe Schrauben: Schritt 1, Bild 1 von 1
    • Vor der Demontage des iPhones entlade die Batterie auf unter 25%. Eine geladene Lithium-Ionen Batterie kann Feuer fangen und/oder explodieren, wenn sie beschädigt wird.

    • Schalte dein iPhone ab, bevor du mit der Demontage beginnst.

    • Entferne die beiden 3,6 mm langen Pentalobe P2 Schrauben neben dem Lightning Connector.

    When reconnecting be VERY careful not to over tighten. The connectors on the screen that these 3.6mm Pentalobe screws lock with are notorious for breaking off

    Blair Tryba - Antwort

    what do i do if ive managed to tighten them too hard and now they wont come off?

    kristian686 -

    Before opening the phone, I gently warmed it using a buckwheat heating pad. This made removal of the adhesive strips (steps 20 to 24) easy.

    Howard Bales - Antwort

    Exactly what I did as well, the gently warming made the adhesive removal work like a charm. The heat as well help to lift the screen easily, no need for the prying tools for me to open te phone.

    For the adhesive removal just pull it slowly to the bottom of the phone and keep in under tension.

    On reassembly, turn on the phone after getting all connectors back in place to verify all is working fine before putting all screws back in their spot.

    Maarten Vergauwen -

    Thanks for the suggestion! I heated up a hot/cold pack, and it worked great.

    Linda Chandler -

    I put mine back together but mine looks very different than this one. Why is it that when I make a call I cannot hear through the ear piece and have to put it on speaker. Also my screen doesn't go black when my face touches it

    Bailey Wilson - Antwort

    Hey Bailey, which repair were you attempting? Is it possible you have a 6s, or maybe a 6 Plus? You may have better luck with faster troubleshooting if you post in our Answer Forum!

    Sam Goldheart -

    See its a long time ago you had this issue. You can try to remove the cable from front camera/sensor/earpiece from the motherboard port and gently push it back on. All the problems you relate to is thru the same cable. If this dont solve your problem, check if the earpiece is correctly placed onto the polarity poles, and that the proximity sensor is lying right down into the corresponding socket. If something is blocking the sensor, yeah then the screen wont turn on/off when you put it onto your ear.

    Kenneth Hilstan -

    I see in the preamble that when you replace your logic board, you would lose touch id functionality, so my question is what if you have the homebutton and thus the fingerprint reader for the logic board replacement, would touch id work?

    socratesmens - Antwort

    The guide for the iPhone6 battery replacement needs to be revised. There are a couple of issues.

    1) While the battery cover has two screws, they are different lengths. Since they are very small, it can be hard to see the difference (until one tries to screw the smaller one into the longer hole). The video needs to mention this.

    2) The application of the adhesive strip if very different from what is mentioned. Also, there is a “one piece plastic” applique, and it is very unforgiving. The video should show this process in more detail.

    I believe the attention to this detail would help folks correctly install their iPhone 6 batteries, and with the recent Apple disclosed battery problem, would continue to show that iFixit is very committed to the end-user.

    Gary Long - Antwort

    I felt a bit silly getting stuck at the end of a long repair, unable to screw one of these last screws back in. What worked was gently pinching the phone above and below the screw, to make sure the screen and back were perfectly aligned.

    Matt D - Antwort

    Apple edits posts on their Communities website that link to this fix page justifying as follows:

    “We’ve edited your post because following the procedures at the site you provided may lead to damage to the user’s device.”

    What is certain is that following Apple Support’s advice of resetting our phones again and again never works whereas this fix works. Apparently Apple does not want people to know that their hardware fails and can be fixed, because then they would need to explain why they don’t offer neither the fixing service nor the fixing advice by directing us to this website.

    Brice - Antwort

    Before you get started, I suggest you confirm you are replacing the correct camera. If you are thinking of a camera, the front is the side of the device with the main lens. On an iPhone this is actually known as the rear facing camera. Once the phone is disassembled your orientation can be distorted and it is not that hard to fail to realize your are replacing the wrong camera. Doh!

    William Miller - Antwort

    I found it very useful to use a magnet sheet when doing these repairs. I use electrical tape or a sharpie to make a grid, and place each micro screw in a separate box on the grid.

    I work directly over the magnet sheet, so that if something drops I have a better chance at not losing it.

    If you do lose a screw, go over the work area with a fridge magnet. It will pick it up if it hasn’t popped too far away.

    Megan Telliano - Antwort

    I agree. The Magnetic Project Mat makes your project incredibly easier and keeps your screws/parts organized. Here is the link for anyone interested:

    Magnetic Project Mat

    Cooper -

    or some masking tape with sticky side up and the ends folded underneath on a piece of paper, then you can write notes like

    “1.4mm for FOO bracket →”

    “7x2.3mm for EMI cover, different one by camera →”

    The arrows point as appropriate.

    If you drop something, put a flashlight on the floor & shine it across the floor — Turn off ceiling & other lights off to maximize the shadow from the flashlight.

    Bass Clef -

    These screws are tiny, and the first two are the biggest of the lot. Get a magnifying glass or good reader glasses.

    Jennifer Porter - Antwort

    Which torx is this T?

    klemenecanze - Antwort

    The screws are no torx screws they are Apple Pentalobe screws. You need to buy a Pentalobe screwdriver seen above.

    Claes -

    I have to use the P2 right?

    Aman Singh - Antwort

    The best advice I can give is not to perform this operation over carpet.

    Bruce codding - Antwort

    I'm an amateur, but I was able to replace the parts almost perfectly while looking at this explanation, thank you very much.

    irichin.3.26 - Antwort

    was fairly easy more nerves than anything, one thing one should have on hand is alcohol just in case its needed. also if one doesn’t get the entire tape strips out, use the alcohol like suggested and lift the battery up. Then can grab the remaining tape strips with tweezers and pull it out. Easy to put back together just make sure the connectors are in. The screws are tiny so take your time. I plugged it in and it started charging and it worked. Great to have my 6 back for a trip as I wanted to use it for the camera, also my game phone so nice to have a battery that lasts. Yes having a flat place to put the parts and put them in separate area so they don’t get mixed up. It took about a hour with hunting for a spare bottle of alcohol.

    Greg Wischmeyer - Antwort

    The first step should always to be to backup your phone as there is always a slim chance that even a simple battery replacement may render the phone inoperable and data on it lost.

    Jim - Antwort

    Please do not forget to remove the SIM-Card tray!!

    Steffen Albrecht - Antwort

    I didn’t need to remove my sim card tray when I did my iPhone 6 battery replacement. Why do you suggest to remove it?

    Jim -

    You dont need to remove sim card while battery replacement

    bertan - Antwort

    Did mine today, with iFixit battery and iFixit tool kit. Did not need suction cup, to open case, as it had partially sprung open on left, as a result of a badly swollen battery. Supported base and screen with a bookend and rubber bands. This kept these parts at a 90 degree angle, so that screen did not need to be removed. IFixit screwdriver tips were perfect fit. Somewhat difficult to remove battery adhesive strips, but slow and steady got it done, after mild heating with hair dryer. Took about 3 minutes to reposition battery connector…just a wee bit tricky, to position correctly. Was careful to place top of screen in place first, and remainder snapped into place with light pressure, and replaced the 2 pentalobe screws.

    Will highly recommend iFixit for such a repair. Repair kit and battery, are first rate. I give this an 11, out of 10.?

    Len Drasin - Antwort

  2. iPhone 6 SIM Auswurfhebel ersetzen, Anleitung für die Anti-Clamp: Schritt 2, Bild 1 von 3 iPhone 6 SIM Auswurfhebel ersetzen, Anleitung für die Anti-Clamp: Schritt 2, Bild 2 von 3 iPhone 6 SIM Auswurfhebel ersetzen, Anleitung für die Anti-Clamp: Schritt 2, Bild 3 von 3
    • Wir haben die Anti-Clamp entwickelt, um Geräte sicher zu öffnen. Die nächsten beiden Schritte zeigen die Benutzung der Anti-Clamp. Wenn du sie nicht verwenden willst, überspringe die nächsten zwei Schritte und folge einer anderen Methode.

    • Genaue Anweisungen, wie die Anti-Clamp benutzt wird, findest du hier.

    • Drücke den blauen Griff zum Scharnier hin, um den Öffnungsmodus zu deaktivieren.

    • Bringe die Saugheber nahe an der Unterkante des iPhones direkt über dem Home Button an, einen auf der Vorderseite, den anderen auf der Rückseite.

    • Drücke die Saugheber auf den Oberflächen fest.

    • Wenn die Saugheber nicht gut auf den Flächen haften, dann klebe Paketband darüber.

    I found that the single suction cup from the kit worked very well. It didn’t take that much force to separate the front panel from the phone. I think any suction cup that you are able to get a firm grip on will probably work as well. There isn’t any adhesive holding the front panel in. It just snaps in and out. If you have a cracked screen and no screen protector, it may be hard to get a good suction seal. If that’s the case, someone else here suggested applying clear tape to the front glass to get a good surface for applying the suction cup. In my case, I already had a screen protector that was still intact so the suction cup sealed easily.

    fiftysomething - Antwort

    WORKED PERFECTLY… easy, no harm at all…. thanks a lot

    carlos restrepo -

  3. iPhone 6 SIM Auswurfhebel ersetzen: Schritt 3, Bild 1 von 3 iPhone 6 SIM Auswurfhebel ersetzen: Schritt 3, Bild 2 von 3 iPhone 6 SIM Auswurfhebel ersetzen: Schritt 3, Bild 3 von 3
    • Drücke den blauen Griff vorwärts, um die Arme wieder zu verriegeln.

    • Drehe den Griff eine volle Umdrehung im Uhrzeigersinn, oder bis du merkst, dass sich die Saugheber dehnen.

    • Achte darauf, dass sich die Saugheber weiterhin gegenüber stehen. Wenn sie sich nicht mehr gegenüber stehen, dann löse die Saugheber ein wenig ab und schiebe sie in die richtige Position.

    • Schiebe ein Plektrum unter das Display, sobald die Anti-Clamp eine ausreichend große Lücke erzeugt hat.

    • Wenn es nicht gelingt, mit der Anti-Clamp einen ausreichenden Spalt zu erzeugen, dann drehe den Griff eine Viertelumdrehung im Uhrzeigersinn weiter.

    • Drehe den Griff jeweils nicht mehr als eine Viertelumdrehung weiter und warte jedes Mal einige Sekunden lang. Gib der Anti-Clamp Zeit, ihre Arbeit zu erledigen.

    • Überspringe die nächsten drei Schritte .

  4. iPhone 6 SIM Auswurfhebel ersetzen, SIM-Karte: Schritt 4, Bild 1 von 2 iPhone 6 SIM Auswurfhebel ersetzen, SIM-Karte: Schritt 4, Bild 2 von 2
    • Stecke ein SIM-Karten Eject Werkzeug oder eine Büroklammer in das kleine Loch des SIM-Karten Einsatzes.

    • Drücke, um den Einsatz auszuwerfen.

    • Dies benötigt vielleicht mehr Kraft als gedacht.

    Why isn’t this the first step in the process? Seems unnecessarily risky to fumble with popping the SIM in and out when you’ve already opened up the phone.

    Perrin Haley - Antwort

    If you don’t have something small enough to open it, you can use the lever when the screen is off.

    Lucas Rowlands -

    I actually removed the simcard as the first step because I didn’t want to risk fumbling with an open phone (as someone previously mentioned)

    twcheng93 - Antwort

  5. iPhone 6 SIM Auswurfhebel ersetzen: Schritt 5, Bild 1 von 1
    • Entferne den SIM-Karten Einsatz aus dem iPhone.

    • Achte beim wieder einsetzen darauf, dass die SIM-Karte in der korrekten Ausrichtung im Einsatz steckt.

    After reassembly phone would not detect SIM Card.

    During repair while components were out of phone I used that opportunity to straighten the back case that was bent. While straightening the back case I bent the thin edge of the back case by the SIM Card slot. SIM Card would click into place and seemed to make a good connection but the phone would not detect the SIM Card. After really straightening the back case by the SIM Card slot almost back to cherry the phone would now detect the SIM Card. The tray has to fit really flush with the case.

    johncrowley111 - Antwort

    My flashlight has stopped working altogether. It was intermittent for a while. I believe them to be original. When I try to use the flash on my camera app, it flashes weakly but not enough do really help. Any chance the flex went bad or is there a logic board issue? My other two iphones with the same apps and the same updates are not having any problems.

    Jason Stein - Antwort

    Bonjour j'ai un iphone 6 problème réseau

    karim kaladi - Antwort

  6. iPhone 6 SIM Auswurfhebel ersetzen, SIM Auswurfhebel: Schritt 6, Bild 1 von 1
    • Entferne die einzelne 1,7 mm Kreuzschlitz #00 Schraube, die den SIM Auswurfhebel befestigt.

    Remova o parafuso Phillips # 00 de 1,7 mm que fixa a alavanca de ejeção do SIM.

    Maximiliano Fischer - Antwort

  7. iPhone 6 SIM Auswurfhebel ersetzen: Schritt 7, Bild 1 von 2 iPhone 6 SIM Auswurfhebel ersetzen: Schritt 7, Bild 2 von 2
    • Entferne den SIM Auswurfhebel aus dem iPhone.

    • Merke dir die Ausrichtung für den Wiederzusammenbau: Das breitere Ende sollte auf Höhe des Loches für den SIM-Karten Auswurf sein.

    Frage: gleiche Vorgehensweise für IPhone 8?

    r.albinger - Antwort

Abschluss

Arbeite die Schritte in umgekehrter Reihenfolge ab, um dein Gerät wieder zusammenzubauen.

47 weitere Nutzer:innen haben diese Anleitung absolviert.

Besonderer Dank geht an diese Übersetzer:innen:

en de

100%

Jasper Fleischhauer hilft uns, die Welt in Ordnung zu bringen! Wie kann ich mithelfen?
Hier starten ›

Sam Goldheart

Mitglied seit: 10/18/12

465.252 Reputation

538 Anleitungen geschrieben

Team

iFixit Mitglied von iFixit

Staff

136 Mitglieder

16.573 Anleitungen geschrieben

3 Kommentare

Bonjour, mon tiroir ne sort pas sauf quand j’appuie sur le téléphone pour le compresser, il manquerait une rondelle ou autre épaisseur ? merci

Farid Le Déglingo - Antwort

Where can we purchase the eject lever though?

Crav - Antwort

So i recently did a rear housing replacement and forgot to but the eject lever in before putting in my sim card is there any way to fix this

if so email Nanakyeretwie46@gmail.com

Nana Kyeretwie - Antwort

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 1

Letzte 7 Tage: 8

Letzte 30 Tage: 54

Insgesamt: 46,815