Zum Hauptinhalt wechseln

Repariere deine Sachen

Recht auf Reparatur

Werkzeug & Ersatzteile

Einleitung

Deine Selfie-Kamera funktioniert nicht mehr? Dann ist es vielleicht an der Zeit, die Frontkamera zu ersetzen.

Anhand dieser Anleitung kannst du die Frontkamera-Sensorkabel-Einheit wechseln, einschließlich des Umgebungslichtsensors und dem Mikrofon eines iPhone 7.

Einführungsvideo

  1. Vor dem Beginn sollte der Ladestand des iPhones unter 25 % liegen. Ein geladener Lithium-Ionen Akku kann bei Beschädigung brennen oder explodieren.
    • Vor dem Beginn sollte der Ladestand des iPhones unter 25 % liegen. Ein geladener Lithium-Ionen Akku kann bei Beschädigung brennen oder explodieren.

    • Schalte das iPhone aus, bevor du es auseinandernimmst.

    • Entferne die zwei 3,4 mm Pentalobe Schrauben an der Unterkante des iPhones.

    • Beim Öffnen des Gerätes werden die Dichtungen für den Spritzwasserschutz beschädigt. Halte Ersatzdichtungen bereit, bevor du fortfährst. Wenn du diese nicht ersetzt, ist dein Gerät nach der Reparatur nicht mehr gegen Spritzwasser geschützt.

    Can anyone confirm 7/7P's pentalobe screws have a ring of seal near the screw head?

    Cooper Chase - Antwort

    Confirmed, the screws have a black ring seal around the head.

    rcheing - Antwort

    Can’t get the display front

    Bernadette Pfeifer - Antwort

    From personal experience, I highly recommend before doing this procedure or any other, that you do a backup of your phone (preferably local) in case your procedure goes south.

    ballina5ny - Antwort

    I purchased the repair tools with the replacement battery from iFixit. The tools include a screw driver and three heads none were labeled 3.4 mm. I think the one that fit the pentalobe screws was labeled Y000. The guide should identify the screw driver head supplied by the kit not 3.4mm.

    Mark Lieberman - Antwort

    in the iphone 7 replacement battery kit from iFixit, the screwdriver that fits the 3.4 mm pentalobe screws is labeled P2 (and not Y000)

    Jan-Tijn Oppermann -

    the screwdriver PH000 does not work i wasted two screws and now they dont have the 4 cross mark they are now a circle, i buyed it all from Paraguay and it doesnt work, had to assembly back the parts because i got stuck like i mention with some screws, well im just going to send to a professional to install, thanks

    Martin Frutos, Nuñez - Antwort

  2. Durch Erwärmen der unteren Kante des iPhones lässt es sich leichter  öffnen, weil der Klebstoff darunter weich wird.
    • Durch Erwärmen der unteren Kante des iPhones lässt es sich leichter öffnen, weil der Klebstoff darunter weich wird.

    • Benutze einen Haartrockner oder erwärme einen iOpener und lege ihn etwa eine Minute lang auf die untere Kante des iPhones, um den Kleber darunter aufzuweichen.

    ¿Cuántos segundos son los recomendados?

    joscarlos91 - Antwort

    Sesenta segundos

    Krutav Shah -

    It is a process. I heated the lower area of the phone with a hair dryer on and off (1min each) about 3-4 times before I was able to get the provided tool in.

    Dan - Antwort

    I suggest using a hairdryer. I used the iOpener for maybe 30 mins to no avail. However, when I used the hairdryer the screen came of much quicker.

    Michael - Antwort

    I totally Mr. Myagi’ed it, by rubbing my hands together until they burned, then held the phone un my hot hands. I did this 5-6 times over a couple of minutes. It was a good zen way to get started!

    Ark - Antwort

    Can a heat gun be used?

    Lee - Antwort

    Absolutely. Just don’t overdo it—the adhesive usually softens up pretty easily. If you are experienced with a heat gun, you’ll have no problem. (If you are inexperienced, it’s easy to cook the display or cause other damage.)

    Jeff Suovanen -

    If i use this process, will iphone 7 still be sealed, water/ splash resist after that?

    Marius Serban - Antwort

    Opening the iPhone's display will compromise its waterproof seals. Have replacement seals ready before you proceed past this step, or take care to avoid liquid exposure if you reassemble your iPhone without replacing the seals.

    Angel Hermida -

    Can I use a cpb heating pad to soften the adhesive ? If yes how much time and temperature ?

    davidecongiu - Antwort

    Will doing this compromise the screen protector (Zagg) that I have on my phone?

    Eric Nance - Antwort

    Hairdryer worked for me but I needed to use a razor to pry it open at the bottom then used the spudger

    Gina Torres - Antwort

    Is there a reason why you wouldn’t put the iopener over the entire length of the phone, instead of just the bottom corner?

    BPX - Antwort

    The motherboard is extremely sensitive to heat.

    Neal Reasland -

    Hello can the head damage the id touch bottom?

    After heating opening it stoped working.

    Qrizmasex @ gmail . Com

    aratovski - Antwort

    It definitely can. That happened to me.

    Steve Naylor -

    mine didnt come with a heat pack do i use a hair dryer

    Shy Rose - Antwort

  3. Setze einen Saugnapf auf die untere Hälfte des Displays, knapp über dem Home Button. Achte darauf, dass der Saugnapf nicht auf dem Home Button aufliegt. Dies würde verhindern, dass sich ein Vakuum zwischen dem Saugnapf und dem Glas bildet.
    • Setze einen Saugnapf auf die untere Hälfte des Displays, knapp über dem Home Button.

    • Achte darauf, dass der Saugnapf nicht auf dem Home Button aufliegt. Dies würde verhindern, dass sich ein Vakuum zwischen dem Saugnapf und dem Glas bildet.

    • Wenn dein Display stark gesplittert ist, dann haftet der Saugheber vielleicht besser, wenn du die Scheibe mit durchsichtigem Paketband abdeckst. Du kannst anstelle des Saughebers auch sehr kräftiges Klebeband benutzen. Wenn das alles nicht hilft, dann klebe den Saugheber mit Sekundenkleber an der zerbrochenen Scheibe fest.

    The glass is completely cracked and the suction cup doesn't work because it gets air in between. any tip?

    Display is glued and doesn't come off.

    support - Antwort

    A wide, single strip of packing tape, well placed, will solve this for you. :)

    Mimic44444 - Antwort

    Last comment works well. Thank you !

    Using packing tape for a cracked screen should be included in the description in Step 3.

    Cracked screen is most probably the reason you are replacing it.

    Arni Benediktsson - Antwort

    I agree that using packing tape for a cracked screen should be included in this steps description. I don’t have wide but turned mine horizontal and that worked great.

    Mary Knapp - Antwort

    Bekomme die Oberschale einfach nicht runter! Trotz mehrmaligem erwärmen durch den iOpener und seitlichen bewegen! Weiß nicht mehr weiter!

    Stephan Lienhard - Antwort

    Wouldn’t that screw up the Touch ID?

    Rexx Havok - Antwort

  4. Ziehe etwas am Saugnapf, bis sich eine kleine Lücke zwischen der Displayeinheit und dem Rückgehäuse bildet. Führe die flache Seite eines Spudgers in diese Lücke ein. Der wasserdichte Klebestreifen, welcher das Display in Position hält, ist sehr stark. Es kann viel Kraft brauchen, um diese erste kleine Lücke zu schaffen. Solltest du dabei Schwierigkeiten haben, wackle das Display etwas auf und ab, um den Klebestreifen zu schwächen, damit du den Spudger leichter einführen kannst.
    • Ziehe etwas am Saugnapf, bis sich eine kleine Lücke zwischen der Displayeinheit und dem Rückgehäuse bildet.

    • Führe die flache Seite eines Spudgers in diese Lücke ein.

    • Der wasserdichte Klebestreifen, welcher das Display in Position hält, ist sehr stark. Es kann viel Kraft brauchen, um diese erste kleine Lücke zu schaffen. Solltest du dabei Schwierigkeiten haben, wackle das Display etwas auf und ab, um den Klebestreifen zu schwächen, damit du den Spudger leichter einführen kannst.

    This was SO hard for me to do with the spudger. I couldn’t get a gap to insert it because my phone was so cracked (even though I used tape on the front) to get a solid seal with the suction cup. I ended up taking a VERY thin knife and inserting it straight down to make the initial break that allowed me to insert the spudger.

    jessica harlow - Antwort

    I’ve given up using a plastic spudger to try to open any of these phones. I use a metal one with a flat base and a very sharp end…close to a razor. As long as I’m careful, it won’t slip and scratch the base. It’s much easier than using these plastic spudgers.

    mcr4u2 -

    I confirm that the plastic spudger it’s not the best tool for this operation. I suggest to use a larger metal tool like a “Jimmy” or “iSesamo open tool” (I used the first one)

    Cristef -

    Im trying to get the screen off right now and my phone is not cracked and its still a pain

    Jordon Johnson - Antwort

    Using a blow dryer was extremely helpful and using the suction cup towards one of the lower edges was also helpful

    Jordon Johnson - Antwort

    This is not working for me. How long does the heat need to be applied? Still trying right now…. =/

    Chris Gallego - Antwort

    Apply hair dryer for at least 1 minute. I inserted the tip end of a thin mini screwdriver and with some force, pryed it open and inserted my plastic spudger to continue the separation process. It worked, just be patient.

    Please wear protective glasses! My iPhone glass was severely cracked, when separating the glass a corner area of broken glass exploded in my face. Apply transparent tape over the broken glass to contain the shards.

    amberron - Antwort

    I second Jessica’s January 8 comment.  I just finished a battery replacement on my iPhone 7 and this step was the most nerve-wracking part.  I ended up using a sharper (but not razor-sharp) metal object to get this done with confidence (tried the spudger and guitar pick but not thin enough).  The tool I used was the exact duplicate of what iFixIt calls “iSesamo Opening Tool” in their tool selection.  I did the heat up with a hair dryer (after attempts with an iOpener hot pad) and the secret (as Jessica also noted)  was to not use the angle of attack shown in the pictures, but to push it in more vertically along the bottom edge while pulling up on the suction cup.  From there you can easily lever the tool to the lower angle-of-attack (as shown in the picture).  I actually used the metal tool for most of the perimeter as well, just don’t go deep (you don’t need to).  Notes: my display was intact, and I was able to pull up fairly hard with a glass screen protector still on it.

    Ted - Antwort

    This is frustrating. I heated the lower edge with a hair dryer for 1 min on high about 3-4 times. In between each heat cycle, I rocked the suction cup back and forth. I was eventually able to create significant space for the provided tool. This takes a lot of patience. Once the space was created, it was very easy to remove the screen.

    Dan - Antwort

    use a fingernail, then the blue tool, then the spudger

    Therese Peffer - Antwort

    The iOpener worked just fine for me. Had to keep it on for a few minutes. I also was able to get the suction cup seal right close to the edge, over top of the home button for added leverage. Used the blue tool and transitioned to the spudger. Slow, steady pressure…and patience. ;)

    johnhall918 - Antwort

    Unable to open an iPhone 7 display assembly. Used gell pack at 150 degrees F. The phone wouldn’t budge when I used the iFixit suction cut. Part of the problem is that the cup doesn’t adhere for long before it looses suction. I suspect it would work better on unbroken glass, but that doesn’t help me now. After spending a lot of time at this, I changed heating methods to a hot air heater. I raised the temp of the bottom end of the phone to, ultimately, 175 degrees, and used a variety of tools to try to pry the glass apart enough to get a spudger (or anything) in, but it didn’t even lift enough for a double-edged razor blade to get in. I’ve been trying this for hours now, and about to give up and throw a lot more money at this to have a service perform the work. I figured that 175 was as high as I should need to go to soften the adhesive without damaging the electronics. Should I have gone higher? I see no mention of measured temps in any instructions or comments.

    ted - Antwort

    Have you tried applying tape to the broken screen? This will help a lot with keeping the suction cup on it.

    Christian Groothuis -

    It doesn’t need to get very hot; pulling up on the display is mainly what does the trick. Make sure the two pentalobe screws have been removed and then try the tricks in this step. If all else fails, superglue the suction cup to your display and let it cure, and then pull. Keep in mind you only need a tiny gap to insert a plastic pick and start cutting the adhesive. Good luck!

    Jeff Suovanen -

    Just a question. After this operation the impermeability function was compromitted?

    bentek86 - Antwort

    The trick I found, was to add packing tape right across the bottom over the home button then use hairdryer on the end, then suction cup on the very bottom and it lifted enough to get a gap. No one mentioned how it would be impossible to handle the phone after the hairdryer ;)

    Andrew Lansdowne - Antwort

    Didn’t have an iOpener and 60 seconds on a hairdryer wasn’t doing it for me. Still wouldn’t budge. I had to take a very sharp razor along the seam at the bottom between the speakers. It took about 20 passes for it to separate enough to get the spudger in. Make sure you keep the razor at a 90-45˚ angle and that it goes no more than 1-2mm into the phone. The bottom of the phone is metal, but the casing for the screen is plastic. So if you cut lower than a 45˚ (flat with the phone) you risk cutting into the casing. Apply light pressure when making the passes. I would just do the razor on the flat part on the bottom.

    minimalist - Antwort

    I used a hair drier while lifting up at the same time until I could get the too inside. The seal is pretty finicky. Just take your time and you should be fine. Work the hair drier and the tool all the way around before lifting the screen up and off. There will likely be sealant stuck between the screen and phone. You can just break it with the tool.

    Ray Bieze - Antwort

    This step was impossible for me despite using a blow dryer and having no cracks on the screen. I finally took it to a local repair place and had them do battery replacements for two iPhone 7’s. The girl let me watch her do it. She used a razor blade (just until she had a small opening that she could hold open with her fingernail) and confirmed that she too would have difficulty opening it with a plastic tool and suction cup. The plastic tool was great for prying the rest of it open once a crack was there, but she said she would never try to use that as the tool to initially open it. The tools provided for initially prying open the screen are inadequate.

    Chad Twedt - Antwort

    Hopeless - no chance to get the screen off without any damage. No matter what tools, heat etc.

    Anatole Beams - Antwort

    I second what others have said, definitely use a razor blade to break the seal! Heat helps some, but too much direct heat is bad for the screen. Would have been impossible if I hadn’t read the comments, thanks everybody!

    Kit - Antwort

    Use extreme caution on this step. I was just replacing my battery and now i’m buying a new screen. The screen was very stuck, I pulled to hard and it popped off suddenly, completely destroying the screen.

    moose - Antwort

    When the right heat is reached, the easiest way is to use a metal iFlex to create the initial gap, then insert the Jimmy or iSesamo next to it so the gap gets bigger, at this point you can get in with the flat edge of a plastic spudger and slowly slide it in the borders to cut the adhesive. You will still need to force a bit the upper end to separate the screen by pulling it down while keeping up the screen, and twist to the right. I hope this is clear enough. Never apply too much strength too quickly anyway.

    Stefano Restuccia - Antwort

  5. Ziehe das Werkzeug nach links, entlang dem unteren Rand des iPhones. Drehe das Werkzeug, um die Lücke zwischen dem Display und dem Rückgehäuse weiter zu vergrößern. Drehe das Werkzeug, um die Lücke zwischen dem Display und dem Rückgehäuse weiter zu vergrößern.
    • Ziehe das Werkzeug nach links, entlang dem unteren Rand des iPhones.

    • Drehe das Werkzeug, um die Lücke zwischen dem Display und dem Rückgehäuse weiter zu vergrößern.

    Didn’t have an iOpener and 60 seconds on a hairdryer wasn’t doing it for me. Still wouldn’t budge. I had to take a very sharp razor along the seam at the bottom between the speakers. It took about 20 passes for it to separate enough to get the spudger in. Make sure you keep the razor at a 90-45˚ angle and that it goes no more than 1-2mm into the phone. The bottom of the phone is metal, but the casing for the screen is plastic. So if you cut lower than a 45˚ (flat with the phone) you risk cutting into the casing. Apply light pressure when making the passes. I would just do the razor on the flat part on the bottom.

    minimalist - Antwort

    I used a hairdryer and a razor

    Gina Torres - Antwort

    The photos are a con. You cannot get a spudger in unless you can lift the screen. You cannot lift the screen because of the adhesive. Using a anything metal will damage the paintwork or the glass edge.

    Anatole Beams - Antwort

    I agree, these guides are half imaginary idealism it seems. A thin metal edge pushed vertically down just a fraction of a mm will cause the adhesive to weaken better than any amount of heat, but affects the final appearance sadly.

    Jesse de Vries - Antwort

  6. Ziehe das Werkzeug von der unteren Ecke die linke Seite hinauf zu den Lautstärketasten und dem Stumm-Schalter. Heble nicht am oberen Rand des Gerätes, sonst riskierst du die Plastikclips, die das Display befestigen, zu beschädigen. Heble nicht am oberen Rand des Gerätes, sonst riskierst du die Plastikclips, die das Display befestigen, zu beschädigen.
    • Ziehe das Werkzeug von der unteren Ecke die linke Seite hinauf zu den Lautstärketasten und dem Stumm-Schalter.

    • Heble nicht am oberen Rand des Gerätes, sonst riskierst du die Plastikclips, die das Display befestigen, zu beschädigen.

    Be VERY careful on this next step going up the right side of the phone. There is a ribbon cable 1/3 of the way up from the bottom that is very close to the edge. Do NOT use the blue triangle!!!! Just lightly rotate the spudger to get separation on the edge.

    Timothy Varvais - Antwort

  7. Führe das flache Ende eines Spudgers in die rechte untere Ecke des Geräts ein. Drehe das Werkzeug, um die entstehende Lücke zwischen der Displayeinheit und dem Rückgehäuse zu vergrößern. Ziehe die flache Seite des Werkzeugs entlang der rechten Seite nach oben, um den Klebestreifen zu lösen, der das Display fixiert.
    • Führe das flache Ende eines Spudgers in die rechte untere Ecke des Geräts ein.

    • Drehe das Werkzeug, um die entstehende Lücke zwischen der Displayeinheit und dem Rückgehäuse zu vergrößern.

    • Ziehe die flache Seite des Werkzeugs entlang der rechten Seite nach oben, um den Klebestreifen zu lösen, der das Display fixiert.

    • Schiebe den Spudger nicht tiefer als den Klebestreifen ein, damit die empfindlichen Flachbandkabel am rechten Rand unbeschädigt bleiben.

  8. Ziehe am Saugnapf, um das Display anzuheben und das iPhone zu öffnen. Hebe das Display nicht höher als bis zu einem 10 Grad Winkel, denn rechts sitzen Flachbandkabel, welche das Display mit dem Logic Board verbinden.
    • Ziehe am Saugnapf, um das Display anzuheben und das iPhone zu öffnen.

    • Hebe das Display nicht höher als bis zu einem 10 Grad Winkel, denn rechts sitzen Flachbandkabel, welche das Display mit dem Logic Board verbinden.

    do not pull up pull sideways it will brake

    Riley Patterson - Antwort

    Made this mistake

    rachael.grime - Antwort

    Somehow my phone turned itself back on during the opening. Scared me a little, like a patient coming out of anesthesia during the operation. I was able to turn it back off. Gotta be more careful where you grab this thing.

    Bryant Larsen - Antwort

  9. Löse den Saugnapf vom Front Panel und nimm ihn ab.
    • Löse den Saugnapf vom Front Panel und nimm ihn ab.

  10. Fahre mit einem Opening Pick am oberen Rand des iPhones, zwischen dem Rückgehäuse und dem Front Panel entlang, um den restlichen Klebstoff, der das Display hält, zu lösen. Achte darauf, nicht die Plastikclips am oberen Rand des Gerätes zu beschädigen.
    • Fahre mit einem Opening Pick am oberen Rand des iPhones, zwischen dem Rückgehäuse und dem Front Panel entlang, um den restlichen Klebstoff, der das Display hält, zu lösen.

    • Achte darauf, nicht die Plastikclips am oberen Rand des Gerätes zu beschädigen.

    The plastic clips mentioned are on the top of the screen being replaced… so not sure why it matters not to break them. Trick here was to pull the screen downwards to open a gap at the top and then insert as shown and raise to break the seal.

    Andrew Lansdowne - Antwort

    This is relevant for other guides than the display replacement guide.

    jvalaamo -

  11. Nintendo Switch Kits

    Eine schnelle Lösung, um wieder ins Spiel zu kommen

    Switch Kits kaufen

    Nintendo Switch Kits

    Eine schnelle Lösung, um wieder ins Spiel zu kommen

    Switch Kits kaufen
  12. Ziehe die Displayeinheit etwas von der oberen Kante des Telefons weg, um die Clips zu lösen, die sie am Rückgehäuse halten. Öffne das iPhone, indem du das Display von der linken Seite her aufklappst, wie die Rückseite eines Buches. Versuche nicht, das Display schon komplett zu entfernen, da empfindliche Kabel das Display immer noch mit dem Logic Board verbinden!
    • Ziehe die Displayeinheit etwas von der oberen Kante des Telefons weg, um die Clips zu lösen, die sie am Rückgehäuse halten.

    • Öffne das iPhone, indem du das Display von der linken Seite her aufklappst, wie die Rückseite eines Buches.

    • Versuche nicht, das Display schon komplett zu entfernen, da empfindliche Kabel das Display immer noch mit dem Logic Board verbinden!

    I just broke the cable to the battery!

    No Bama - Antwort

    same dude im such a freak lol omg haha

    Aiden Polaski - Antwort

    Are there replacements ribbons?

    Blax Bently - Antwort

    Has anyone else noticed very small squares of rubber with a circle cut through it (I think they fall off into the phone when dismantling)?

    I just replaced my screen and worked out that these are actually a wee pocket that slips over the pentalobe screw holes on the replacement screen. I’m not sure if it’s an additional water resisting mechanism or if it’s to add additional traction for the screws

    richarddillon - Antwort

    Thanks, I was wondering where those were from!

    Albert -

    Same, I only had one fall out and I had no idea if important, and didn’t re-add - because I wasn’t sure where it fell from - but it was definitely from the home screen button….watch it be important. -__-

    Nicole Crome -

    I just broke cable connecting camera and earpiece speaker to logic board. Be careful with it.

    Natan Haładyn - Antwort

    This section is missing a critical step - to lay some Post-It notes or something below the right half of the phone when you swing it open, so the ribbon cables don’t get sliced by the sharp edge of the phone case. I broke the Home Button ribbon cable because there was no strain relief when I laid it open.

    neila - Antwort

    I also broke the home button cable and now I have to use assistive touch.

    Laurencio Gonzalez - Antwort

    Keep the suction cup on the display to keep it propped up while you disconnect the ribbon cables.

    minimalist - Antwort

    I broke the short ribbon cable that attaches underneath the lower connector bracket. Be SURE when you lift the display, you do it from left to right. I thought I had the phone oriented correctly in my hand, but I was mistaken.

    John Murray - Antwort

    Put the suction cup on the right side of the middle of the screen when you rotate it up and out. It serves as a nice stand to take the pressure off the connectors.

    Ray Bieze - Antwort

    no mention of what you do once u open the book. are the ribbons long enough to lie flat  or do we have to keep screen raised while removing screws,, like when we hold screen up 45 degrees while removing 5 screw plat when at top of phone. I only realised how fragile the ribbons are and how important it is to use suction  cup to rest screen on an angle so ribbons don't stretch or cut on frame.

    thanks for the above comments and probably the most important section. I just hope I closed t before I fdid any damage. its lke the fragility of iPhone 3’s all over again.

    scallyteacher - Antwort

    I just broke one of the cables… yeah, it is not nice… I’m lucky in the sense the screen is still working, but the button is not.

    Trying a cheap screen on Ebay (that contains the cable) do 20$, after that, it’s a new cellphone…

    Vincent Poirier - Antwort

    • Entferne die vier Tri-Point Y000-Schrauben, die die Abdeckung der unteren Anschlüsse befestigen, sie haben folgende Längen:

    • Drei 1,2 mm Schrauben

    • Eine 2,4 mm Schraube

    • Passe während der ganzen Reparatur gut auf die Schrauben auf und sorge dafür, dass sie genau an ihren alten Platz zurück kommen, sonst kann das iPhone beschädigt werden.

    Ahhh shoot! accidentally ordered tri-wing vs tri-point (must have just looked for y000).. It seems they only did this to annoy repair folks because not everything is tri-point on the phone...

    Steve - Antwort

    These screws just spin for me. They don't back out, but the heads aren't stripped either. I've tried applying backpressure to help lift the screws, but no luck

    Jeff Hurst - Antwort

    The Y000 took out one of the screws but not the other 3. I even tried the PH000 as suggested but nothing.

    dbright - Antwort

    What driver do I need to remove these screws i’m stuck

    Nasser Nader - Antwort

    i cant use, the Y000 it isnt working.

    joscarlos91 - Antwort

    What if I stripped a screw what do I do??

    Jacob Ramos - Antwort

    Yep, only the 2.4mm came out, other 3 won’t budge, and worried I’ve stripped the heads. Anyone got any ideas?

    Stephen Babbage - Antwort

    It’s the screwdriver bit that is the problem. I had the same issue with 2 Y000 bits not grabbing the screw properly. I fixed it by using a small 3 sided file to slightly grind the groves in the Y000 bit just a bit deeper. Then the bit worked like a charm on these screws.

    Jim Staples - Antwort

    Use Y000 on all 4. U have to be very sensitive on the 1.2mm screws. Put the bit in the screw, put the left pointing finger on top of the screwdriver and turn the driver carefully to the right until you feel a “bump”, thats the trick :-), then you are able to screw the screw out.

    Magne Eivindson - Antwort

    For me the key here was a LOT of downward pressure to ensure the Y000 bit caught in the screw. Not sure i can describe how much exactly, but is was significant. Otherwise the bit would not catch.

    Erik Fredriksen - Antwort

    What do I do if I Stripped one of them?

    Adam Corral - Antwort

    Can’t get them removed what to do ?

    cowling_luke - Antwort

    Managed to get the central one out. The upper one won't move, the lower one I've popped out with some force. This allows you to rotate the cover enough to unplug the various bits. Not ideal, but works. I've tried applying a lot of pressure, using the tighten/ loosen method, but the heads have just got mashed… no wonder Samsung are now No1, sigh…

    jimpoolio - Antwort

    You need to be careful when just rotating the cover as you can accidentally slice through the two black antennas! You only need to nip them…As you can tell I have done this in the past :/

    Kyle Webb -

    The first, longer screw came out fine, but the other three wouldn’t budge, regardless of more/less pressure or a slight angle or anything. I finally filed down the tip of the Y000 bit ever so slightly, and then it worked. Hope this helps someone.

    Harmony Vine - Antwort

    Filing down the bit worked for me. The tip about putting an index finger on the end of the screwdriver handles and then turning gently until it clicks into place was very helpful! Using these 2 tips I didn't need much downward pressure. Screws are out in a few turns.

    Chris Bennett - Antwort

    If you can’t get the bit to grip the screw properly, you can use a little bit of the water-proof sealing between the bit and the screw. That worked for me. Hope this helps anyone.

    jvalaamo - Antwort

    Mine came out easily. I placed the screws in the area where the bit goes in my kit so I can keep track.

    Gina Torres - Antwort

    I used a bunch of medicine cups to track my screws. You need like 12 if you want them all in cups. I ran out. There are so many different sizes that literally vary by 1mm. The tolerances on these things are tight.

    Ray Bieze - Antwort

    I use a 28 day pill box and keep every screw separate and reburn to exact slot because they all vary in length, width and can really damage u phone if too long and nt secure if to small.  use a magnetised screwdriver,  or make the cheap freebees magnetic for a short period by rubbing it up an a magnet. lol

    scallyteacher - Antwort

    Absolutely ridiculous had to go get a different one just stupid

    mark golling - Antwort

    I couldn’t get the lowest one out and just turned the metal bracket out of the way and replaced battery.

    qwerty77x - Antwort

  13. Entferne die Abdeckung der unteren Anschlüsse.
    • Entferne die Abdeckung der unteren Anschlüsse.

    my battery cable connector was stuck to the bottom of this metal bracket plate so be careful when you lift it off

    Josh Martin - Antwort

    This may have been intentionally done by Apple to make sure the battery gets disconnected before any other connector is disconnected. So always make sure to disconnect the battery before disconnecting and reconnecting the connectors for the display.

    Oscar Moreno - Antwort

  14. Mit der Spitze eines Spudgers kannst du den Stecker der Batterie vom Anschluss auf dem Logic Board heben. Biege das Kabel leicht nach unten, um zu verhindern, dass es mit dem Anschluss in Berührung kommt und das Telefon mit Strom versorgt. Biege das Kabel leicht nach unten, um zu verhindern, dass es mit dem Anschluss in Berührung kommt und das Telefon mit Strom versorgt.
    • Mit der Spitze eines Spudgers kannst du den Stecker der Batterie vom Anschluss auf dem Logic Board heben.

    • Biege das Kabel leicht nach unten, um zu verhindern, dass es mit dem Anschluss in Berührung kommt und das Telefon mit Strom versorgt.

    Was kann passieren wenn man diesses Kabel vergessen hat zu entfernen `?

    Julian Eltrich - Antwort

    Reconnecting the battery poorly can cause the iPhone to appear to be properly powered and functional, but then suffer a reboot loop.

    I had difficulty after a screen replacement, and the Console app on my Mac showed that the ‘thermalmonitord’ process was throwing lots of errors from not getting any sensor readings from the battery. It would never charge past 1% and just kept rebooting.

    The contacts on this conector looked fine so even though I had reseated this connector several times already, I reconnected it very firmly using my thumb and a spudger to really press all the corners and middle and really gave it a good massage and then finally it showed the normal dead battery screen and started properly charging and eventually booted back up to normal functionality.

    It seems the battery has to be able to transmit data to the phone to say it’s not overheating or iOS will not allow any current into the battery to recharge it, and the kernel will panic from the null readings and just reboot over and over again.

    jason - Antwort

  15. Bevor du in diesem Schritt ein Kabel ablöst oder wieder verbindest, musst du den Akku abtrennen. Nutze das Flache Ende deines Spudgers oder deinen Fingernagel, um die Anschlüsse des Flachbandkabels am unteren Ende des Displays zu lösen. Um die Stecker wieder zu verbinden musst du diese unbedingt erst an einer Seite, dann an der gegenüberliegenden herunterdrücken. Drücke nicht in der Mitte, da sie sich verbiegen und im schlimmsten Fall funktionsunfähig werden können.
    • Bevor du in diesem Schritt ein Kabel ablöst oder wieder verbindest, musst du den Akku abtrennen.

    • Nutze das Flache Ende deines Spudgers oder deinen Fingernagel, um die Anschlüsse des Flachbandkabels am unteren Ende des Displays zu lösen.

    • Um die Stecker wieder zu verbinden musst du diese unbedingt erst an einer Seite, dann an der gegenüberliegenden herunterdrücken. Drücke nicht in der Mitte, da sie sich verbiegen und im schlimmsten Fall funktionsunfähig werden können.

    • Wenn du nach dem Zusammenbau deines Smartphones ein leeres Display, weiße Streifen, teilweisen oder kompletten Ausfall des Touchscreens hast, dann versuche nochmals diese beiden Kabel abzutrennen und sorgfältig wieder anzuschließen. Achte darauf, dass sie wirklich fest sitzen.

    To be honest you don’t really need to disconnect the display cables in step 15 or 16 to get the battery out. Just keep the suction cup on the screen to keep it propped up and to give the cables some slack. The only reason to take these cables off is that it’s a pain to apply the replacement display adhesive with those cables in the way. If you’re not re-waterproofing your phone just leave these attached.

    Austausch der iPhone Display Klebestreifen

    minimalist - Antwort

    MAKE SURE you hold the top screen when dislodging the cable connections. I let the screen lie flat down and ended up tearing one of the cable connections, now my touch ID does not work at all! I’m going to have to order a whole new screen.

    Arjun Nagarajan - Antwort

  16. Entferne die beiden 1,3 mm Kreuzschlitz Schrauben, die die Abdeckung über den Sensoren der Display Einheit befestigt. Entferne die Abdeckung. Entferne die Abdeckung.
    • Entferne die beiden 1,3 mm Kreuzschlitz Schrauben, die die Abdeckung über den Sensoren der Display Einheit befestigt.

    • Entferne die Abdeckung.

    Has anyone had trouble getting these two screws off? I’ve been working on these for about 10 minutes and the LEFT screw wont spin. It seems like the little PH000 screwdriver bit won’t even grip it. (The one of the right comes off, no problem)

    It looks like I’ll have to pick this project up again with a screwdriver that will actually take off this piece.

    Makana Sylva - Antwort

    The right screw kept spinning, tried different levels of force but didn’t work. I left the screw on and bent the shield to get to the cable.

    s h - Antwort

    I used a #1 flat head tip to loosen.

    Peter Pearson - Antwort

    I couldn’t get the two screws out either—used the correct screw tip and everything. Stripped the screw. Will now attempt to just keep the cable attached…..

    Therese Peffer - Antwort

    Use the PH000 and apply a little more force before spinning, should come right out!

    Sierra Scolaro - Antwort

    ^To anyone having trouble, this is the correct answer. Put the phone on a firm surface, align your driver carefully, press down hard, and twist. As long as your driver is approximately the right size, it’ll come out.

    Jeff Suovanen -

    the two screw i have are stripped and i have n way of getting either screws off whats my next bet

    Alexis Marie Colon - Antwort

    The PH000 bit is to large. I can’t get the screws out either which really sucks…now I have to put everything back together, find another bit that will work and try this again another day. Not impressed with IFIXIT’s attention to detail so far :-(

    Ryan Welborn - Antwort

    Using iFixit’s driver kit, I prefer a PH00 for this, which is larger than the PH000. If you think the PH000 is too big, something is wrong.

    Jeff Suovanen -

    I think part of the issue with the iFixit PH000 is that it is slightly too pointy. The PH00 fits better because the splines engage the slots of the screw before the point bottoms out. The PH000 tip bottoms out in the screw’s center point and the splines don’t engage as well. I have other PH000 tips that are more blunt nose and they work better than the iFixit bit.

    rcarswell - Antwort

    Use the J00 bit. Worked perfectly

    efazio588 - Antwort

    PH000 screwdriver didn’t work for any of these screws, or the barometric vent, or the taptic engine. It was too big. I had to use a different screwdriver from another kit I had.

    minimalist - Antwort

    I’d do this step before removing the ribbon cables by the battery connector. That way you can disconnect all of them at the same time.

    Ray Bieze - Antwort

    i used the little +-shape 30 mm screwdriver (not the Y…but the + shape).

    mason - Antwort

    the cable tore. is that it i need a new phone?

    patricia loving - Antwort

    You don’t need a new phone, but your selfie camera and phone speaker will not work. You can get replacements for that about $10.

    jack jones - Antwort

    Reconnecting this cable and coverplate took a good 20 minutes. O_O

    Nicole Crome - Antwort

    What can I do to remove the screw (I stripped it)

    Alex Vu - Antwort

    I also had issues to loosen up the screws, in two parts the right side up and the left side down, i think the PH000 is to pointy or something or its too hard for the srews of the iphone, i cannot take it off and know im regreting i bought i order all the way from Paraguay in south america and know so angry it doesnt work

    Martin Frutos, Nuñez - Antwort

  17. Entferne den Stecker der Display Einheit von seinem Anschluss auf dem Logic Board. Der Stecker sollte nicht mittig festgesteckt werden, um ein Verbiegen zu vermeiden.
    • Entferne den Stecker der Display Einheit von seinem Anschluss auf dem Logic Board.

    • Der Stecker sollte nicht mittig festgesteckt werden, um ein Verbiegen zu vermeiden.

    Das ist sehr mutig, das Kabel dort so zu strapazieren.

    Mich würde das Display daneben stellen und mit irgendetwas stützen, dass es nicht umkippen kann um Beschädigungen an dem Kabel zu vermeiden. Das reißt sehr schnell ein.

    Detlef Menninger - Antwort

    Is this the connector for the earpiece, as well? I did the screen replacement and everything worked, except now I can’t use my earpiece… I’m afraid I didn’t fully connect this particular portion.

    Victor Bui - Antwort

    @victorbui714 Correct, this is also the connector for the earpiece speaker. Check the flex cable carefully and make sure it wasn’t pinched or torn. Make sure the connector socket is clean (give it a blast with some compressed air if needed) and try reseating it. If that doesn’t help, you may want to remove the earpiece speaker and inspect the four springs on the back, and check that they’re intact and making good contact with the four circular pads on the flex cable. Give the pads a wipe with some IPA and try not to leave any skin oils on them. If none of that works, try replacing the entire flex cable/sensor assembly. Good luck!

    Jeff Suovanen -

  18. Entferne die Display Einheit.

    When removing the screen, be aware of the two tiny square black rubber grommets on the Penelope screw brackets that secure the screen. They can fall off very easily and be lost without even knowing it (it happened to me, but was lucky enough to find them).

    Guy Cooley - Antwort

    Sorry, I’m so unclear about when to replace the Adhesive tape. Should I put the iPhone 7 Display Assembly Adhesive at this step, or after I’ve replaced the battery?

    Victor Bui - Antwort

    @victorbui714 Battery first, then adhesive during reassembly, as it says in the instructions. ;)

    Jeff Suovanen -

    This is the 3rd screen iv put in my phone and everyone them bust at the top by the camera every time iv bought one of these screen idk if it’s the manufactures fault or what?

    trent bost - Antwort

    @trentb28922 Ouch! That’s not normal. Is your phone’s frame bent? Are you having to use a lot of force when you install the display?

    Jeff Suovanen -

  19. Löse die drei Kreuzschlitz Schrauben, welche die Abdeckung des Ohrhörer-Lautsprechers mit dem Display verbinden
    • Löse die drei Kreuzschlitz Schrauben, welche die Abdeckung des Ohrhörer-Lautsprechers mit dem Display verbinden

    • Zwei 2,6 mm Schrauben

    • Eine 1,7 mm Schraube

    I am measuring the screws; my digital caliper measures both the top at 1.88mm not 2.6

    Marco Cueva - Antwort

    I just checked the screw measurements and they match what’s shown in the guide. Are you sure you’re looking at the right screws?Are you sure your caliper is accurate? Was your iPhone serviced in the past and reassembled incorrectly? Something isn’t right. The measurements here are the screw lengths, by the way—just in case you were measuring something else.

    Jeff Suovanen -

  20. Entferne die Abdeckung des Ohrhörer-Lautsprechers.
    • Entferne die Abdeckung des Ohrhörer-Lautsprechers.

  21. Entferne die Frontkamera, um an den Ohrhörer-Lautsprecher zu gelangen. Entferne die Frontkamera, um an den Ohrhörer-Lautsprecher zu gelangen.
    • Entferne die Frontkamera, um an den Ohrhörer-Lautsprecher zu gelangen.

  22. Entferne die folgenden beiden Kreuzschlitz Schrauben, welche den Ohrhörer-Lautsprecher mit dem Display verbinden:
    • Entferne die folgenden beiden Kreuzschlitz Schrauben, welche den Ohrhörer-Lautsprecher mit dem Display verbinden:

    • Eine 1,9 mm Schraube

    • Eine 2,5 mm Schraube

    Hi!What size is the third screw?

    Лёха Н - Antwort

  23. Entferne jetzt den Ohrhörer-Lautsprecher.
    • Entferne jetzt den Ohrhörer-Lautsprecher.

  24. Erhitze erneut deinen iOpener und lege ihn auf den oberen Rand der Display Einheit, um den Kleber zu lösen, welcher die Frontkamera und die Sensoreinheit fixiert.
    • Erhitze erneut deinen iOpener und lege ihn auf den oberen Rand der Display Einheit, um den Kleber zu lösen, welcher die Frontkamera und die Sensoreinheit fixiert.

    • Warte mindestens 2 Minuten bevor du mit dem nächsten Schritt weitermachst, damit der Kleber genug Zeit hat, weich zu werden.

  25. Verwende einen Spudger, um den Umgebungslichtsensor vorsichtig aus seiner Vertiefung auf dem Front Panel herauszuhebeln. Versuche dein Werkzeug ganz unter den Sensor zu schieben um es von dem durchsichtigen Plastikteil darunter abzulösen. Wenn du nur gegen das Kabel hebelst, dann kann sich der Sensor von der Kabeleinheit lösen und muss dann ausgewechselt werden. Wenn du sowieso die Sensor/Kabeleinheit austauschen willst, spielt das natürlich keine Rolle.
    • Verwende einen Spudger, um den Umgebungslichtsensor vorsichtig aus seiner Vertiefung auf dem Front Panel herauszuhebeln.

    • Versuche dein Werkzeug ganz unter den Sensor zu schieben um es von dem durchsichtigen Plastikteil darunter abzulösen. Wenn du nur gegen das Kabel hebelst, dann kann sich der Sensor von der Kabeleinheit lösen und muss dann ausgewechselt werden. Wenn du sowieso die Sensor/Kabeleinheit austauschen willst, spielt das natürlich keine Rolle.

    I’m sorry to comment but this step is wrong. The proximity sensor is sticked to the display. I was following this instruction and the sensor was unvelded from the flex cable. Now it’s workless. It’s a fortune that the only problem with the iPhone is that while calling and holding the phone to the ear, the display doesn’t turn off.

    I recommend to gently pushing against the transparent plastic enclosure near the sensor and once it’s unsticked, keep pushing against the sensor’s body. In this way the sensor welding doesn’t bear/support any extra load on it.

    At least, my iPhone 7G had the sensor sticked to the display. Maybe some day I will replace it (around 20€ - 25€ on ebay)

    I won't claim to iFixit nor stop using this website. Whenever I higly recommend to iFixt technitians to revise such kind of “errors”. At least for expensive devices like Apple products.

    Miguel Cretu - Antwort

    I editted this guide and added these two comments. I already know about this “trick”. It’s your own decision to follow my suggestion or not.

    Miguel Cretu - Antwort

    I have fixed 2 screens now on iPhone 7. The 1st time I didn’t have this problem, 2nd time I did. I would agree with Miguel Cretu and save yourself the hassle and remove the sensor and it’s surround altogether.

    Wayne Lyell - Antwort

    In the second picture, there is the splugger that’s on it’s right is near a little window square, white inside. I’ve checked my replacement display and it don’t have inside in WHITE in this little window . Anyone know why have this color (it is not a sticker) and what is the reason? Thanks

    fakirox - Antwort

    I also had to pop out the clear plastic surround of the front camera to put into my new screen. It’s just glued in, so heat and pop it out with a spudger. Best to do this step last so you don’t accidentally tear any ribbons.

    Grant Barker - Antwort

    I actually found that removing the assembly from the other side (like the step 35) is a bit easier. Also, heat is really useful! I took an hair dryer, and for at least 3 minutes I heated by interval the piece, and at the end, the glue was so soft, it was really easy to remove!

    Vincent Poirier - Antwort

  26. Schiebe nun das Plektron Richtung Kameragehäuse und trenne so den Kleber, der das Kabel am Front Panel festhält. Stoppe kurz vor dem Gewinde. Schiebe nun das Plektron Richtung Kameragehäuse und trenne so den Kleber, der das Kabel am Front Panel festhält. Stoppe kurz vor dem Gewinde. Schiebe nun das Plektron Richtung Kameragehäuse und trenne so den Kleber, der das Kabel am Front Panel festhält. Stoppe kurz vor dem Gewinde.
    • Schiebe nun das Plektron Richtung Kameragehäuse und trenne so den Kleber, der das Kabel am Front Panel festhält. Stoppe kurz vor dem Gewinde.

  27. Nutze nun das Plektron, um das Kamerakabel von den beiden Kunststoffnippeln auf dem Front Panel zu lösen und es von den letzten Kleberesten zu befreien. Nutze nun das Plektron, um das Kamerakabel von den beiden Kunststoffnippeln auf dem Front Panel zu lösen und es von den letzten Kleberesten zu befreien. Nutze nun das Plektron, um das Kamerakabel von den beiden Kunststoffnippeln auf dem Front Panel zu lösen und es von den letzten Kleberesten zu befreien.
    • Nutze nun das Plektron, um das Kamerakabel von den beiden Kunststoffnippeln auf dem Front Panel zu lösen und es von den letzten Kleberesten zu befreien.

    на рисунке №2 винт 3 отсутствует, на рисунке № 3 винт 3 присутствует. нет описание где он был вывинчен. последний винт с правой стороны, около камеры

    Vitaly Savin - Antwort

  28. Entferne die Frontkamera und das Sensorkabel.
    • Entferne die Frontkamera und das Sensorkabel.

    Look at the camera assembly closely. There are two cables soldered together. Do not separate the pieces by mistake . Get the pick all the way below both ,and they will come off together.

    turboduck2 - Antwort

    Good statement I made that mistake on my first iPhone 7 Plus !

    Jaye - Antwort

    Its not mentioned here but there is a small philips screw at the top left that you may have to transfer to your new lcd panel

    Steve - Antwort

    Hi Steve, what is the main work of this little strip with 2 small contact? Antenna? Shield?

    Thanks

    fakirox -

    I’ve separated the sensor and front facing camera, can I just press them back together or will I need a complete replacement

    Dominic Sore - Antwort

    About Steve comment, anyone know what is this small screw with two contact? It is an antenna ?? Shield??? Thanks

    fakirox - Antwort

    I’m also looking for info on the screw on the immediate left of the top left corner of the speaker. Did you find the info out?

    Cheers!

    Mike Grandbois - Antwort

Abschluss

Um dein Gerät wieder zusammenzubauen, folge dieser Anleitung in umgekehrter Reihenfolge.

99 weitere Nutzer haben diese Anleitung absolviert.

Besonderer Dank geht an diese Übersetzer:

100%

Diese Übersetzer helfen uns, die Welt in Ordnung zu bringen! Wie kann ich mithelfen?
Beginne zu übersetzen ›

Evan Noronha

Mitglied seit: 05.02.2015

191.693 Reputation

178 Anleitungen geschrieben

Team

iFixit Mitglied von iFixit

Community

124 Mitglieder

11.594 Anleitungen geschrieben

Question ..... I have a clear square plastic piece (open in the center) with a tab on one side. What is that for?

Mike McCleery - Antwort

Holds the lens in place.

Edward L Johnson III -

No that is for the ambient light sensor. LCD replacements come with it already installed on em’, so you can toss it if you see it on the replacement already. The larger, circular plastic piece is for the lens.

Brandon Neves -

Does the iPhone 7 plus Front Camera and Sensor Cable Replacement has to do anything with the earpieces speaker? i have replace my iphone 7 plus screen and front camera and sensor cable replacement and speaker and it still doesn’t work. what could really be wrong with my iphone 7 plus?

Saleka Chang - Antwort

Awesome tutorial, thank you! I couldn’t have replaced my camera without this! Well I could have but not the right way!!

Cynthia Hollingsworth - Antwort

Hi so i was replacing my screen when this ribbon ripped. Until I can get the part in the mail is there anything else that having this ribbon ripped will do or effect?

herron.tara4 - Antwort

Hiya, I do not believe so. I damaged the ribbon, no obvious signs but must of as worked when the new one was plugged in and it did not appear to have any affect on anything else. Hope this helps.

Charleigh B -

I ripped the cable in half and was able to use my phone fine for two weeks until I had the part in hand and time to make the replacement. Calls had to be on speaker or in headphones, and I needed to manually adjust my screen brightness throughout the day. You also won't have a selfie cam.

rJ Jarecki -

I replaced my friends screen after he smashed it, must of damaged the cable as once put together the phone was on Apple logo and could not get it to turn on. Had a feeling it was the sensor and it was. Ordered a new one from Amazon and turned on straight away.

The phone would not turn on with the old one plugged in or not so couldn't be 100% but it worked and now have a happy friend. Luckily I didn't restore the phone too!

Charleigh B - Antwort

I bought the replacement from iFixit, and afterwards, the selfie camera didn’t work. and the reason for the replacement was to fix the speaker problem, because I count really understand anymore the phone calls and it also didn’t change the problem. Also the speaker was replaced with an ifixit part. and now the Touch ID is also not working.

Michael Blechinger - Antwort

the flex of iphone 7 plus are compatible with the iphone 7?

Rolando Queral - Antwort

I am looking at doing this replacement because I am having trouble with siri hearing me. I believe the earpiece microphone is in this cable but it is not listed on the part description. Can anyone verify this?

Nick P - Antwort

In this image, the microphone is the gold rectangle with the foam pad on top. You can see it being separated from the screen in Step 27.

Jeff Suovanen -

Replaced the camera, but now my microphone does not work. I can listen to voicemails from both the top and loud speaker, as well as sound over the lightning and Bluetooth connection. A pair of headphones (external mic?) Will not enable phone calls or voice recorder, but will let me listen to music.

Any thoughts on resolving this issue?

rJ Jarecki - Antwort

Double-check the connectors and re-seat them; check for damage to the cables; remove the part and make sure the microphone isn’t blocked by adhesive or other debris. If all else fails, try installing the old part (or replacing it a second time) in case you received a defective microphone. Good luck!

Jeff Suovanen -

Ho sostituito la fotocamera frontale del mio IPhone 7 Plus ma adesso se faccio una foto o un video dal app fotocamera funziona perfettamente mentre se provo a fare una video chiamata con whatsapp, messenger o altre app non funziona, come mai?

PakyScat - Antwort

I replaced the front camera of my IPhone 7 Plus but now if I take a photo or video from the camera app it works perfectly while if I try to make a video call with whatsapp, messenger or other apps it does not work, can you help?

PakyScat - Antwort

Is it possible to repurpose an iPhone 6 or iPhone 6s front camera, to install it in an iPhone7

Kwame S - Antwort

Kommentar hinzufügen

Statistik anzeigen:

Letzten 24 Stunden: 75

Letzten 7 Tage: 641

Letzten 30 Tage: 2,820

Insgesamt: 96,062