Zum Hauptinhalt wechseln

Einleitung

Für eine leichtere Reparatur kannst du unseren Reparatursatz benutzen. Folge dazu dieser kürzeren Anleitung, um die komplette Displayeinheit auszutauschen.

Wenn du mehr Erfahrung hast, hilft dir diese Anleitung "nur" die Einheit aus LCD und Touchscreen des iPhone 7 auszutauschen (d.h. das reine Frontpanel). Du musst dazu verschiedene Bauteile vom alten Bildschirm auf das Neuteil übertragen, bevor du es einbaust, inklusive der Frontkameraeinheit, dem Ohrhörer-Lautsprecher, der LCD Abschirmung und dem Home/Touch ID Sensor.

Bei allen Reparaturen am Bildschirm/Display ist es sehr wichtig, sorgfältig den originalen Home Button/TouchID-Sensor vom alten auf das neue Display zu übertragen. Dieser Sensor ist von Apple mit dem originalen Logic Board gepaart, ein Ersetzen macht das iPhone unbrauchbar!

  1. Vor dem Beginn sollte der Ladestand des iPhones unter 25 % liegen. Ein geladener Lithium-Ionen Akku kann bei Beschädigung brennen oder explodieren.
    • Vor dem Beginn sollte der Ladestand des iPhones unter 25 % liegen. Ein geladener Lithium-Ionen Akku kann bei Beschädigung brennen oder explodieren.

    • Schalte das iPhone aus, bevor du es auseinandernimmst.

    • Entferne die zwei 3,4 mm Pentalobe Schrauben an der Unterkante des iPhones.

    • Beim Öffnen des Gerätes werden die Dichtungen für den Spritzwasserschutz beschädigt. Halte Ersatzdichtungen bereit, bevor du fortfährst. Wenn du diese nicht ersetzt, ist dein Gerät nach der Reparatur nicht mehr gegen Spritzwasser geschützt.

    Can anyone confirm 7/7P's pentalobe screws have a ring of seal near the screw head?

    Cooper Chase - Antwort

    Confirmed, the screws have a black ring seal around the head.

    rcheing - Antwort

  2. Wenn dein Displayglas zerbrochen ist, dann solltest du weiteren Bruch verhindern und Verletzungen während der Reparatur vermeiden, indem du das Glas mit Klebeband abklebst. Klebe durchsichtiges Klebeband in überlappenden Streifen über das Display des iPhones, bis die ganze Oberseite bedeckt ist. Dieses Verfahren hält Glasscherben fest und sorgt dafür, dass die Struktur erhalten bleibt, wenn du am Display hebelst und es hochhebst.
    • Wenn dein Displayglas zerbrochen ist, dann solltest du weiteren Bruch verhindern und Verletzungen während der Reparatur vermeiden, indem du das Glas mit Klebeband abklebst.

    • Klebe durchsichtiges Klebeband in überlappenden Streifen über das Display des iPhones, bis die ganze Oberseite bedeckt ist.

    • Dieses Verfahren hält Glasscherben fest und sorgt dafür, dass die Struktur erhalten bleibt, wenn du am Display hebelst und es hochhebst.

    • Ziehe eine Schutzbrille auf, um deine Augen vor Glassplittern zu schützen, die bei der Reparatur herausspringen können.

    • Wenn die Scheibe so zerbrochen ist, dass ein Saugheber bei den nächsten Schritten zu schwierig anzusetzen ist, dann solltest du versuchen ein Stück sehr starken Klebebands (etwa Panzerband) zu einem Handgriff zusammenzukleben und damit die Glasscheibe anzuheben.

    In case of broken glass you can make the suction cup much more effective by covering the glass with a broad piece of translucent tape which eliminate air leakage through cracks in the glass.

    lionno1 - Antwort

    Il n’est pas nécessaire de mettre beaucoup de scotch.

    Au contraire plus vous mettez de scotch, plus il y aura de défauts et la ventouse ne collera pas.

    Une bande bien positionnée suffit.

    Chloé Bossuette - Antwort

    I’ve used hot glue on low setting to remove all types of crystals. The hot glue will release with a little iso alcohol. No damage to glass or plastic faced crystals or screens. Use a narrow piece of wood as a prying handle.

    Emilio Gonzalez - Antwort

    I recently had issues with removing the glass with the suction cup. I have done this many times with older generation iPhones but this time the glass seemed sealed on quite solidly. I told myself that the last option would be to use the screwdriver tip. After all my attempts, I transitioned to the option of using the screwdriver tip. Surprisingly, it was the easiest thing ever. I placed the 1mm flathead screwdriver at the interface between the glass and the cover (normal start location) and pried up very gently. Voila, the glass came up and I can’t even notice any dents or scratches. It felt much easier than the suction cup technique. If the suction cup is giving you a hard time consider using that 1mm flathead.

    forhereyesonly - Antwort

  3. Durch Erwärmen der unteren Kante des iPhones lässt es sich leichter  öffnen, weil der Klebstoff darunter weich wird.
    • Durch Erwärmen der unteren Kante des iPhones lässt es sich leichter öffnen, weil der Klebstoff darunter weich wird.

    • Benutze einen Haartrockner oder erwärme einen iOpener und lege ihn etwa eine Minute lang auf die untere Kante des iPhones, um den Kleber darunter aufzuweichen.

    ¿Cuántos segundos son los recomendados?

    joscarlos91 - Antwort

    Sesenta segundos

    Krutav Shah -

    It is a process. I heated the lower area of the phone with a hair dryer on and off (1min each) about 3-4 times before I was able to get the provided tool in.

    Dan - Antwort

    I suggest using a hairdryer. I used the iOpener for maybe 30 mins to no avail. However, when I used the hairdryer the screen came of much quicker.

    Michael - Antwort

    I totally Mr. Myagi’ed it, by rubbing my hands together until they burned, then held the phone un my hot hands. I did this 5-6 times over a couple of minutes. It was a good zen way to get started!

    Ark - Antwort

    Can a heat gun be used?

    Lee - Antwort

    Absolutely. Just don’t overdo it—the adhesive usually softens up pretty easily. If you are experienced with a heat gun, you’ll have no problem. (If you are inexperienced, it’s easy to cook the display or cause other damage.)

    Jeff Suovanen -

    If i use this process, will iphone 7 still be sealed, water/ splash resist after that?

    Marius Serban - Antwort

    Opening the iPhone's display will compromise its waterproof seals. Have replacement seals ready before you proceed past this step, or take care to avoid liquid exposure if you reassemble your iPhone without replacing the seals.

    Angel Hermida -

    Can I use a cpb heating pad to soften the adhesive ? If yes how much time and temperature ?

    davidecongiu - Antwort

    Will doing this compromise the screen protector (Zagg) that I have on my phone?

    Eric Nance - Antwort

  4. Setze einen Saugnapf auf die untere Hälfte des Displays, knapp über dem Home Button. Achte darauf, dass der Saugnapf nicht auf dem Home Button aufliegt. Dies würde verhindern, dass sich ein Vakuum zwischen dem Saugnapf und dem Glas bildet.
    • Setze einen Saugnapf auf die untere Hälfte des Displays, knapp über dem Home Button.

    • Achte darauf, dass der Saugnapf nicht auf dem Home Button aufliegt. Dies würde verhindern, dass sich ein Vakuum zwischen dem Saugnapf und dem Glas bildet.

    The glass is completely cracked and the suction cup doesn't work because it gets air in between. any tip?

    Display is glued and doesn't come off.

    support - Antwort

    A wide, single strip of packing tape, well placed, will solve this for you. :)

    Mimic44444 - Antwort

    Last comment works well. Thank you !

    Using packing tape for a cracked screen should be included in the description in Step 3.

    Cracked screen is most probably the reason you are replacing it.

    Arni Benediktsson - Antwort

    I agree that using packing tape for a cracked screen should be included in this steps description. I don’t have wide but turned mine horizontal and that worked great.

    Mary Knapp - Antwort

    Bekomme die Oberschale einfach nicht runter! Trotz mehrmaligem erwärmen durch den iOpener und seitlichen bewegen! Weiß nicht mehr weiter!

    Stephan Lienhard - Antwort

    Wouldn’t that screw up the Touch ID?

    Rexx Havok - Antwort

  5. Ziehe etwas am Saugnapf, bis sich eine kleine Lücke zwischen der Displayeinheit und dem Rückgehäuse bildet. Führe die flache Seite eines Spudgers in diese Lücke ein. Der wasserdichte Klebestreifen, welcher das Display in Position hält, ist sehr stark. Es kann viel Kraft brauchen, um diese erste kleine Lücke zu schaffen. Solltest du dabei Schwierigkeiten haben, wackle das Display etwas auf und ab, um den Klebestreifen zu schwächen, damit du den Spudger leichter einführen kannst.
    • Ziehe etwas am Saugnapf, bis sich eine kleine Lücke zwischen der Displayeinheit und dem Rückgehäuse bildet.

    • Führe die flache Seite eines Spudgers in diese Lücke ein.

    • Der wasserdichte Klebestreifen, welcher das Display in Position hält, ist sehr stark. Es kann viel Kraft brauchen, um diese erste kleine Lücke zu schaffen. Solltest du dabei Schwierigkeiten haben, wackle das Display etwas auf und ab, um den Klebestreifen zu schwächen, damit du den Spudger leichter einführen kannst.

    This was SO hard for me to do with the spudger. I couldn’t get a gap to insert it because my phone was so cracked (even though I used tape on the front) to get a solid seal with the suction cup. I ended up taking a VERY thin knife and inserting it straight down to make the initial break that allowed me to insert the spudger.

    jessica harlow - Antwort

    I’ve given up using a plastic spudger to try to open any of these phones. I use a metal one with a flat base and a very sharp end…close to a razor. As long as I’m careful, it won’t slip and scratch the base. It’s much easier than using these plastic spudgers.

    mcr4u2 -

    I confirm that the plastic spudger it’s not the best tool for this operation. I suggest to use a larger metal tool like a “Jimmy” or “iSesamo open tool” (I used the first one)

    Cristef -

    Im trying to get the screen off right now and my phone is not cracked and its still a pain

    Jordon Johnson - Antwort

    Using a blow dryer was extremely helpful and using the suction cup towards one of the lower edges was also helpful

    Jordon Johnson - Antwort

    This is not working for me. How long does the heat need to be applied? Still trying right now…. =/

    Chris Gallego - Antwort

    Apply hair dryer for at least 1 minute. I inserted the tip end of a thin mini screwdriver and with some force, pryed it open and inserted my plastic spudger to continue the separation process. It worked, just be patient.

    Please wear protective glasses! My iPhone glass was severely cracked, when separating the glass a corner area of broken glass exploded in my face. Apply transparent tape over the broken glass to contain the shards.

    amberron - Antwort

    I second Jessica’s January 8 comment.  I just finished a battery replacement on my iPhone 7 and this step was the most nerve-wracking part.  I ended up using a sharper (but not razor-sharp) metal object to get this done with confidence (tried the spudger and guitar pick but not thin enough).  The tool I used was the exact duplicate of what iFixIt calls “iSesamo Opening Tool” in their tool selection.  I did the heat up with a hair dryer (after attempts with an iOpener hot pad) and the secret (as Jessica also noted)  was to not use the angle of attack shown in the pictures, but to push it in more vertically along the bottom edge while pulling up on the suction cup.  From there you can easily lever the tool to the lower angle-of-attack (as shown in the picture).  I actually used the metal tool for most of the perimeter as well, just don’t go deep (you don’t need to).  Notes: my display was intact, and I was able to pull up fairly hard with a glass screen protector still on it.

    Ted - Antwort

    This is frustrating. I heated the lower edge with a hair dryer for 1 min on high about 3-4 times. In between each heat cycle, I rocked the suction cup back and forth. I was eventually able to create significant space for the provided tool. This takes a lot of patience. Once the space was created, it was very easy to remove the screen.

    Dan - Antwort

    use a fingernail, then the blue tool, then the spudger

    Therese Peffer - Antwort

    The iOpener worked just fine for me. Had to keep it on for a few minutes. I also was able to get the suction cup seal right close to the edge, over top of the home button for added leverage. Used the blue tool and transitioned to the spudger. Slow, steady pressure…and patience. ;)

    johnhall918 - Antwort

    Unable to open an iPhone 7 display assembly. Used gell pack at 150 degrees F. The phone wouldn’t budge when I used the iFixit suction cut. Part of the problem is that the cup doesn’t adhere for long before it looses suction. I suspect it would work better on unbroken glass, but that doesn’t help me now. After spending a lot of time at this, I changed heating methods to a hot air heater. I raised the temp of the bottom end of the phone to, ultimately, 175 degrees, and used a variety of tools to try to pry the glass apart enough to get a spudger (or anything) in, but it didn’t even lift enough for a double-edged razor blade to get in. I’ve been trying this for hours now, and about to give up and throw a lot more money at this to have a service perform the work. I figured that 175 was as high as I should need to go to soften the adhesive without damaging the electronics. Should I have gone higher? I see no mention of measured temps in any instructions or comments.

    ted - Antwort

    Have you tried applying tape to the broken screen? This will help a lot with keeping the suction cup on it.

    Christian Groothuis -

    It doesn’t need to get very hot; pulling up on the display is mainly what does the trick. Make sure the two pentalobe screws have been removed and then try the tricks in this step. If all else fails, superglue the suction cup to your display and let it cure, and then pull. Keep in mind you only need a tiny gap to insert a plastic pick and start cutting the adhesive. Good luck!

    Jeff Suovanen -

    Just a question. After this operation the impermeability function was compromitted?

    bentek86 - Antwort

    The trick I found, was to add packing tape right across the bottom over the home button then use hairdryer on the end, then suction cup on the very bottom and it lifted enough to get a gap. No one mentioned how it would be impossible to handle the phone after the hairdryer ;)

    Andrew Lansdowne - Antwort

    Didn’t have an iOpener and 60 seconds on a hairdryer wasn’t doing it for me. Still wouldn’t budge. I had to take a very sharp razor along the seam at the bottom between the speakers. It took about 20 passes for it to separate enough to get the spudger in. Make sure you keep the razor at a 90-45˚ angle and that it goes no more than 1-2mm into the phone. The bottom of the phone is metal, but the casing for the screen is plastic. So if you cut lower than a 45˚ (flat with the phone) you risk cutting into the casing. Apply light pressure when making the passes. I would just do the razor on the flat part on the bottom.

    minimalist - Antwort

  6. Ziehe das Werkzeug nach links, entlang dem unteren Rand des iPhones. Drehe das Werkzeug, um die Lücke zwischen dem Display und dem Rückgehäuse weiter zu vergrößern. Drehe das Werkzeug, um die Lücke zwischen dem Display und dem Rückgehäuse weiter zu vergrößern.
    • Ziehe das Werkzeug nach links, entlang dem unteren Rand des iPhones.

    • Drehe das Werkzeug, um die Lücke zwischen dem Display und dem Rückgehäuse weiter zu vergrößern.

    Didn’t have an iOpener and 60 seconds on a hairdryer wasn’t doing it for me. Still wouldn’t budge. I had to take a very sharp razor along the seam at the bottom between the speakers. It took about 20 passes for it to separate enough to get the spudger in. Make sure you keep the razor at a 90-45˚ angle and that it goes no more than 1-2mm into the phone. The bottom of the phone is metal, but the casing for the screen is plastic. So if you cut lower than a 45˚ (flat with the phone) you risk cutting into the casing. Apply light pressure when making the passes. I would just do the razor on the flat part on the bottom.

    minimalist - Antwort

  7. Ziehe das Werkzeug von der unteren Ecke die linke Seite hinauf zu den Lautstärketasten und dem Stumm-Schalter. Heble nicht am oberen Rand des Gerätes, sonst riskierst du die Plastikclips, die das Display befestigen, zu beschädigen. Heble nicht am oberen Rand des Gerätes, sonst riskierst du die Plastikclips, die das Display befestigen, zu beschädigen.
    • Ziehe das Werkzeug von der unteren Ecke die linke Seite hinauf zu den Lautstärketasten und dem Stumm-Schalter.

    • Heble nicht am oberen Rand des Gerätes, sonst riskierst du die Plastikclips, die das Display befestigen, zu beschädigen.

    Be VERY careful on this next step going up the right side of the phone. There is a ribbon cable 1/3 of the way up from the bottom that is very close to the edge. Do NOT use the blue triangle!!!! Just lightly rotate the spudger to get separation on the edge.

    Timothy Varvais - Antwort

  8. Führe das flache Ende eines Spudgers in die rechte untere Ecke des Geräts ein. Drehe das Werkzeug, um die entstehende Lücke zwischen der Displayeinheit und dem Rückgehäuse zu vergrößern. Ziehe die flache Seite des Werkzeugs entlang der rechten Seite nach oben, um den Klebestreifen zu lösen, der das Display fixiert.
    • Führe das flache Ende eines Spudgers in die rechte untere Ecke des Geräts ein.

    • Drehe das Werkzeug, um die entstehende Lücke zwischen der Displayeinheit und dem Rückgehäuse zu vergrößern.

    • Ziehe die flache Seite des Werkzeugs entlang der rechten Seite nach oben, um den Klebestreifen zu lösen, der das Display fixiert.

  9. Ziehe am Saugnapf, um das Display anzuheben und das iPhone zu öffnen. Hebe das Display nicht höher als bis zu einem 10 Grad Winkel, denn rechts sitzen Flachbandkabel, welche das Display mit dem Logic Board verbinden.
    • Ziehe am Saugnapf, um das Display anzuheben und das iPhone zu öffnen.

    • Hebe das Display nicht höher als bis zu einem 10 Grad Winkel, denn rechts sitzen Flachbandkabel, welche das Display mit dem Logic Board verbinden.

    do not pull up pull sideways it will brake

    Riley Patterson - Antwort

    Made this mistake

    rachael.grime - Antwort

  10. Löse den Saugnapf vom Front Panel und nimm ihn ab.
    • Löse den Saugnapf vom Front Panel und nimm ihn ab.

  11. Fahre mit einem Opening Pick am oberen Rand des iPhones, zwischen dem Rückgehäuse und dem Front Panel entlang, um den restlichen Klebstoff, der das Display hält, zu lösen. Achte darauf, nicht die Plastikclips am oberen Rand des Gerätes zu beschädigen.
    • Fahre mit einem Opening Pick am oberen Rand des iPhones, zwischen dem Rückgehäuse und dem Front Panel entlang, um den restlichen Klebstoff, der das Display hält, zu lösen.

    • Achte darauf, nicht die Plastikclips am oberen Rand des Gerätes zu beschädigen.

    The plastic clips mentioned are on the top of the screen being replaced… so not sure why it matters not to break them. Trick here was to pull the screen downwards to open a gap at the top and then insert as shown and raise to break the seal.

    Andrew Lansdowne - Antwort

    This is relevant for other guides than the display replacement guide.

    jvalaamo -

  12. Ziehe die Displayeinheit etwas von der oberen Kante des Telefons weg, um die Clips zu lösen, die sie am Rückgehäuse halten. Öffne das iPhone, indem du das Display von der linken Seite her aufklappst, wie die Rückseite eines Buches. Versuche nicht, das Display schon komplett zu entfernen, da empfindliche Kabel das Display immer noch mit dem Logic Board verbinden!
    • Ziehe die Displayeinheit etwas von der oberen Kante des Telefons weg, um die Clips zu lösen, die sie am Rückgehäuse halten.

    • Öffne das iPhone, indem du das Display von der linken Seite her aufklappst, wie die Rückseite eines Buches.

    • Versuche nicht, das Display schon komplett zu entfernen, da empfindliche Kabel das Display immer noch mit dem Logic Board verbinden!

    I just broke the cable to the battery!

    No Bama - Antwort

    same dude im such a freak lol omg haha

    Aiden Polaski - Antwort

    Are there replacements ribbons?

    Blax Bently - Antwort

    Has anyone else noticed very small squares of rubber with a circle cut through it (I think they fall off into the phone when dismantling)?

    I just replaced my screen and worked out that these are actually a wee pocket that slips over the pentalobe screw holes on the replacement screen. I’m not sure if it’s an additional water resisting mechanism or if it’s to add additional traction for the screws

    richarddillon - Antwort

    Thanks, I was wondering where those were from!

    Albert -

    I just broke cable connecting camera and earpiece speaker to logic board. Be careful with it.

    Natan Haładyn - Antwort

    This section is missing a critical step - to lay some Post-It notes or something below the right half of the phone when you swing it open, so the ribbon cables don’t get sliced by the sharp edge of the phone case. I broke the Home Button ribbon cable because there was no strain relief when I laid it open.

    neila - Antwort

    I also broke the home button cable and now I have to use assistive touch.

    Laurencio Gonzalez - Antwort

    Keep the suction cup on the display to keep it propped up while you disconnect the ribbon cables.

    minimalist - Antwort

    • Entferne die vier Tri-Point Y000-Schrauben, die die Abdeckung der unteren Anschlüsse befestigen, sie haben folgende Längen:

    • Drei 1,2 mm Schrauben

    • Eine 2,4 mm Schraube

    • Passe während der ganzen Reparatur gut auf die Schrauben auf und sorge dafür, dass sie genau an ihren alten Platz zurück kommen, sonst kann das iPhone beschädigt werden.

    Ahhh shoot! accidentally ordered tri-wing vs tri-point (must have just looked for y000).. It seems they only did this to annoy repair folks because not everything is tri-point on the phone...

    Steve - Antwort

    These screws just spin for me. They don't back out, but the heads aren't stripped either. I've tried applying backpressure to help lift the screws, but no luck

    Jeff Hurst - Antwort

    The Y000 took out one of the screws but not the other 3. I even tried the PH000 as suggested but nothing.

    dbright - Antwort

    What driver do I need to remove these screws i’m stuck

    Nasser Nader - Antwort

    i cant use, the Y000 it isnt working.

    joscarlos91 - Antwort

    What if I stripped a screw what do I do??

    Jacob Ramos - Antwort

    Yep, only the 2.4mm came out, other 3 won’t budge, and worried I’ve stripped the heads. Anyone got any ideas?

    Stephen Babbage - Antwort

    It’s the screwdriver bit that is the problem. I had the same issue with 2 Y000 bits not grabbing the screw properly. I fixed it by using a small 3 sided file to slightly grind the groves in the Y000 bit just a bit deeper. Then the bit worked like a charm on these screws.

    Jim Staples - Antwort

    Use Y000 on all 4. U have to be very sensitive on the 1.2mm screws. Put the bit in the screw, put the left pointing finger on top of the screwdriver and turn the driver carefully to the right until you feel a “bump”, thats the trick :-), then you are able to screw the screw out.

    Magne Eivindson - Antwort

    For me the key here was a LOT of downward pressure to ensure the Y000 bit caught in the screw. Not sure i can describe how much exactly, but is was significant. Otherwise the bit would not catch.

    Erik Fredriksen - Antwort

    What do I do if I Stripped one of them?

    Adam Corral - Antwort

    Can’t get them removed what to do ?

    cowling_luke - Antwort

    Managed to get the central one out. The upper one won't move, the lower one I've popped out with some force. This allows you to rotate the cover enough to unplug the various bits. Not ideal, but works. I've tried applying a lot of pressure, using the tighten/ loosen method, but the heads have just got mashed… no wonder Samsung are now No1, sigh…

    jimpoolio - Antwort

    You need to be careful when just rotating the cover as you can accidentally slice through the two black antennas! You only need to nip them…As you can tell I have done this in the past :/

    Kyle Webb -

    The first, longer screw came out fine, but the other three wouldn’t budge, regardless of more/less pressure or a slight angle or anything. I finally filed down the tip of the Y000 bit ever so slightly, and then it worked. Hope this helps someone.

    Harmony Vine - Antwort

    Filing down the bit worked for me. The tip about putting an index finger on the end of the screwdriver handles and then turning gently until it clicks into place was very helpful! Using these 2 tips I didn't need much downward pressure. Screws are out in a few turns.

    Chris Bennett - Antwort

    If you can’t get the bit to grip the screw properly, you can use a little bit of the water-proof sealing between the bit and the screw. That worked for me. Hope this helps anyone.

    jvalaamo - Antwort

  13. Entferne die Abdeckung der unteren Anschlüsse.
    • Entferne die Abdeckung der unteren Anschlüsse.

    my battery cable connector was stuck to the bottom of this metal bracket plate so be careful when you lift it off

    Josh Martin - Antwort

    This may have been intentionally done by Apple to make sure the battery gets disconnected before any other connector is disconnected. So always make sure to disconnect the battery before disconnecting and reconnecting the connectors for the display.

    Oscar Moreno - Antwort

  14. Mit der Spitze eines Spudgers kannst du den Stecker der Batterie vom Anschluss auf dem Logic Board heben. Biege das Kabel leicht nach unten, um zu verhindern, dass es mit dem Anschluss in Berührung kommt und das Telefon mit Strom versorgt. Biege das Kabel leicht nach unten, um zu verhindern, dass es mit dem Anschluss in Berührung kommt und das Telefon mit Strom versorgt.
    • Mit der Spitze eines Spudgers kannst du den Stecker der Batterie vom Anschluss auf dem Logic Board heben.

    • Biege das Kabel leicht nach unten, um zu verhindern, dass es mit dem Anschluss in Berührung kommt und das Telefon mit Strom versorgt.

    Was kann passieren wenn man diesses Kabel vergessen hat zu entfernen `?

    Julian Eltrich - Antwort

  15. Nutze das Flache Ende deines Spudgers oder deinen Fingernagel, um die Anschlüsse des Flachbandkabels am unteren Ende des Displays zu lösen. Um die Stecker wieder zu verbinden musst du diese unbedingt erst an einer Seite, dann an der gegenüberliegenden herunterdrücken. Drücke nicht in der Mitte, da sie sich verbiegen und im schlimmsten Fall funktionsunfähig werden können. Um die Stecker wieder zu verbinden musst du diese unbedingt erst an einer Seite, dann an der gegenüberliegenden herunterdrücken. Drücke nicht in der Mitte, da sie sich verbiegen und im schlimmsten Fall funktionsunfähig werden können.
    • Nutze das Flache Ende deines Spudgers oder deinen Fingernagel, um die Anschlüsse des Flachbandkabels am unteren Ende des Displays zu lösen.

    • Um die Stecker wieder zu verbinden musst du diese unbedingt erst an einer Seite, dann an der gegenüberliegenden herunterdrücken. Drücke nicht in der Mitte, da sie sich verbiegen und im schlimmsten Fall funktionsunfähig werden können.

    To be honest you don’t really need to disconnect the display cables in step 15 or 16 to get the battery out. Just keep the suction cup on the screen to keep it propped up and to give the cables some slack. The only reason to take these cables off is that it’s a pain to apply the replacement display adhesive with those cables in the way. If you’re not re-waterproofing your phone just leave these attached.

    Austausch der iPhone Display Klebestreifen

    minimalist - Antwort

  16. Entferne die beiden 1,3 mm Kreuzschlitz Schrauben, die die Abdeckung über den Sensoren der Display Einheit befestigt. Entferne die Abdeckung. Entferne die Abdeckung.
    • Entferne die beiden 1,3 mm Kreuzschlitz Schrauben, die die Abdeckung über den Sensoren der Display Einheit befestigt.

    • Entferne die Abdeckung.

    Has anyone had trouble getting these two screws off? I’ve been working on these for about 10 minutes and the LEFT screw wont spin. It seems like the little PH000 screwdriver bit won’t even grip it. (The one of the right comes off, no problem)

    It looks like I’ll have to pick this project up again with a screwdriver that will actually take off this piece.

    Makana Sylva - Antwort

    The right screw kept spinning, tried different levels of force but didn’t work. I left the screw on and bent the shield to get to the cable.

    s h - Antwort

    I used a #1 flat head tip to loosen.

    Peter Pearson - Antwort

    I couldn’t get the two screws out either—used the correct screw tip and everything. Stripped the screw. Will now attempt to just keep the cable attached…..

    Therese Peffer - Antwort

    Use the PH000 and apply a little more force before spinning, should come right out!

    Sierra Scolaro - Antwort

    ^To anyone having trouble, this is the correct answer. Put the phone on a firm surface, align your driver carefully, press down hard, and twist. As long as your driver is approximately the right size, it’ll come out.

    Jeff Suovanen -

    the two screw i have are stripped and i have n way of getting either screws off whats my next bet

    Alexis Marie Colon - Antwort

    The PH000 bit is to large. I can’t get the screws out either which really sucks…now I have to put everything back together, find another bit that will work and try this again another day. Not impressed with IFIXIT’s attention to detail so far :-(

    Ryan Welborn - Antwort

    Using iFixit’s driver kit, I prefer a PH00 for this, which is larger than the PH000. If you think the PH000 is too big, something is wrong.

    Jeff Suovanen -

    I think part of the issue with the iFixit PH000 is that it is slightly too pointy. The PH00 fits better because the splines engage the slots of the screw before the point bottoms out. The PH000 tip bottoms out in the screw’s center point and the splines don’t engage as well. I have other PH000 tips that are more blunt nose and they work better than the iFixit bit.

    rcarswell - Antwort

    Use the J00 bit. Worked perfectly

    efazio588 - Antwort

    PH000 screwdriver didn’t work for any of these screws, or the barometric vent, or the taptic engine. It was too big. I had to use a different screwdriver from another kit I had.

    minimalist - Antwort

  17. Entferne den Stecker der Display Einheit von seinem Anschluss auf dem Logic Board. Der Stecker sollte nicht mittig festgesteckt werden, um ein Verbiegen zu vermeiden.
    • Entferne den Stecker der Display Einheit von seinem Anschluss auf dem Logic Board.

    • Der Stecker sollte nicht mittig festgesteckt werden, um ein Verbiegen zu vermeiden.

    Das ist sehr mutig, das Kabel dort so zu strapazieren.

    Mich würde das Display daneben stellen und mit irgendetwas stützen, dass es nicht umkippen kann um Beschädigungen an dem Kabel zu vermeiden. Das reißt sehr schnell ein.

    Detlef Menninger - Antwort

    Is this the connector for the earpiece, as well? I did the screen replacement and everything worked, except now I can’t use my earpiece… I’m afraid I didn’t fully connect this particular portion.

    Victor Bui - Antwort

    @victorbui714 Correct, this is also the connector for the earpiece speaker. Check the flex cable carefully and make sure it wasn’t pinched or torn. Make sure the connector socket is clean (give it a blast with some compressed air if needed) and try reseating it. If that doesn’t help, you may want to remove the earpiece speaker and inspect the four springs on the back, and check that they’re intact and making good contact with the four circular pads on the flex cable. Give the pads a wipe with some IPA and try not to leave any skin oils on them. If none of that works, try replacing the entire flex cable/sensor assembly. Good luck!

    Jeff Suovanen -

  18. Entferne die Display Einheit.

    When removing the screen, be aware of the two tiny square black rubber grommets on the Penelope screw brackets that secure the screen. They can fall off very easily and be lost without even knowing it (it happened to me, but was lucky enough to find them).

    Guy Cooley - Antwort

    Sorry, I’m so unclear about when to replace the Adhesive tape. Should I put the iPhone 7 Display Assembly Adhesive at this step, or after I’ve replaced the battery?

    Victor Bui - Antwort

    @victorbui714 Battery first, then adhesive during reassembly, as it says in the instructions. ;)

    Jeff Suovanen -

    This is the 3rd screen iv put in my phone and everyone them bust at the top by the camera every time iv bought one of these screen idk if it’s the manufactures fault or what?

    trent bost - Antwort

    @trentb28922 Ouch! That’s not normal. Is your phone’s frame bent? Are you having to use a lot of force when you install the display?

    Jeff Suovanen -

  19. Entferne die vier Y000 Schrauben, mit der die Abdeckung des Home / Touch ID-Sensors befestigt ist:
    • Entferne die vier Y000 Schrauben, mit der die Abdeckung des Home / Touch ID-Sensors befestigt ist:

    • Eine 1,1 mm Schraube

    • Drei 1,3 mm Schraube

    • Überdrehe beim Zusammenbau diese Schrauben nicht, sonst funktioniert dein Home Button nicht.

    Why is the screw over top of the home button so difficult to get out… has anyone else experienced this..? This is twice now I've struggled to get that screw

    Brandon - Antwort

    The screw to the left holding the heatshield is never mentioned in this guide

    Beerbo - Antwort

    No reason to touch that screw unless you’re removing the shield—in which case, this step instructs you to remove it.

    Jeff Suovanen -

    So I stripped the screw furthest to the left, how can i possibly remove it now? Can I just buy a new LCD shield and home bracket button and screw and will that work just fine on the new screen replacement? this stripped screw of mine is not coming out

    Bryan Ferrer - Antwort

    That should work, as long as you can still get the home button/sensor out without damage. For removing a stripped screw this size, I’d probably try supergluing it to the driver—or else just drill the top of the screw off and then remove the bracket, leaving the screw shaft embedded in the old display. Good luck!

    Jeff Suovanen -

    I used the same driver for all of these screws. Had to apply a lot of pressure before trying to unscrew it and it was fine.

    jessica harlow - Antwort

    This is wrong, the size you need is Y00 for the 1.1mm screws and Y000 for the 1.3mm one.

    Robert Clark - Antwort

    The heads on those screws are identical. I’ve never had any trouble using a Y000 for all of them. Use whatever works for you I guess.

    Jeff Suovanen -

    I’ve managed to strip the screw on the right hand side - not the far right, just right of the home button. Any ideas on how to get it out without glue (I don’t have any)

    Christie Ellen - Antwort

    My screwdriver is too big to get out the screws

    Coolinee Kerman - Antwort

    My eyesight isn’t what it used to be. That said, the replacement screen that arrived already had screws in the two outside positions. It took me a minute to figure this out when I was trying to install the home button. I couldn’t figure out why the screws weren’t going in. I thought the holes were filled or something… Nope. screws. Took them out and used them.. all good.

    Critter - Antwort

    My 7 had quite a bit of loctite holding these bad boys on. I stripped the one to the right of the home button and after using many “sentence enhancers” I was able to remove it using good tweezers and quite a bit of hand strength. I think that heating up the screws here is not an option because the cables lie underneath the plate and would probably get damaged from the amount of heat needed to loosen the loctite. Be patient here, and maybe have spare Y000 drivers because you may damage your driver getting these screws out.

    P Park - Antwort

    If your having trouble. I recommend you guys to buy the Y00o driver at amazon. It look golden. It works very will .

    Jonathan curz - Antwort

    Read instead of: “Remove the four Y000 screws”. “Remove the four Philips 00 screws”. Thats the case what occurs to me.

    Henk - Antwort

    Hi all, I’m really hoping someone will be able to give me a hand here, so the 1.1mm screw on top of the home button is stripped, and absolutely refuses to get out. I have tried the superglue technique mentioned and am worried it may have even glued the screw to the bracket. The only solution I can think of is to bend the home button bracket on either side of the middle screw, and use the bracket itself to remove the screw from the home button. I have ordered a new home button bracket either way, does anybody have any other ideas? Should I even attempt what I am proposing?

    Thanks in Advance.

    llamalulu42 - Antwort

    Does the ground strap go over or under bracket?

    Marcos Polos - Antwort

  20. Entferne die Abdeckung über dem Home / Touch-ID Sensor.
    • Entferne die Abdeckung über dem Home / Touch-ID Sensor.

  21. Heble unter der linken Kante des Steckers vom Home Button Kabel und löse ihn aus seinem Anschluss heraus. Wenn der Stecker komplett hochklappt, ohne sich zu lösen dann drücke das Kabel an der Oberkante des Steckers mit dem flachen Ende des Spudgers nach unten und heble gleichzeitig die linke Kante des Steckers hoch. Beschädige nicht das Kabel oder den Stecker, sonst kannst du den Sensor auf Dauer zerstören. Wenn der Stecker komplett hochklappt, ohne sich zu lösen dann drücke das Kabel an der Oberkante des Steckers mit dem flachen Ende des Spudgers nach unten und heble gleichzeitig die linke Kante des Steckers hoch. Beschädige nicht das Kabel oder den Stecker, sonst kannst du den Sensor auf Dauer zerstören.

    Well, I just damaged the home button connector in step 31. It is completely off the cable. What now? Can I buy this home button?

    LadyTech - Antwort

    I think you can not do it because your phone is not identify for new cable.

    Ali Alsaed - Antwort

    Best thing to do here is to NOT pry up on the connector, but to insert the pry tool on the left side until the connector is dislodged.

    Oscar Moreno - Antwort

    Good tip. Worked perfectly. Thx.

    Klaus M -

    That worked perfectly, thank you!

    Emily Kretschmer -

    use one pry tool to hold down, another to pull up.

    Christa - Antwort

    I did it. :-( i broke it

    Peter Keller - Antwort

    Anyone having difficulty reconnecting the two ? I’ve been trying for ages with no luck.

    Patrick McKenna - Antwort

    Same problem here - can reconnect them once the new LCD is being installed. Not sure what the trick is.

    edcraigslistaccount -

    my Homebutton don´t work after I reconnect all, I checked all flex cables but it still dont work. what can I do?

    Dr. Dieter - Antwort

    so, i’m working on an iPhone 7. I was very careful not to break anything, I even bought an iOpener heat pack and applied it, and everything went off without a hitch, but when I tested the button, It does not work, would it help to reconnect it or something?

    Thanks a lot!

    Peter Keller - Antwort

    iPhone 7 home “buttons” can be really fussy. You’ll find some good troubleshooting tips here and here. Hope this helps!

    Jeff Suovanen -

    Broke my cable. The picture is not clear but you have to separate the thin silver end of cable from what looks like a black piece of rubber. I pulled up on it from under the black rubber like the picture shows and broke mine.

    bart.hutchings - Antwort

  22. Heble behutsam den darunterliegenden Stecker hoch und biege ihn aus dem Weg für das Home Button/TouchID Kabel. Das iPhone kann bei diesem Schritt leicht beschädigt werden. Arbeite langsam und passe gut auf, wo du dein Hebelwerkzeug ansetzt. Wenn du die TouchID Hardware beschädigst, kann sie nur von Apple repariert werden.
    • Heble behutsam den darunterliegenden Stecker hoch und biege ihn aus dem Weg für das Home Button/TouchID Kabel.

    • Das iPhone kann bei diesem Schritt leicht beschädigt werden. Arbeite langsam und passe gut auf, wo du dein Hebelwerkzeug ansetzt. Wenn du die TouchID Hardware beschädigst, kann sie nur von Apple repariert werden.

    • Wenn sich der Stecker nicht leicht hochhebeln lässt, dann erwärme den Kleber des Steckers mit einem Haartrockner oder einem iOpener, versuche es dann nochmals.

    • Versuche nicht, den Stecker ganz abzulösen - klappe ihn einfach ein wenig hoch, so dass das darunterliegende Home Button/TouchID Sensorkabel entfernt werden kann.

    Make sure that you fold this cable out when fitting your replacement before you fasten the shield back down. I didn’t but managed to loosen 2 screws on the shield to get the cable out.

    chris_sawyer - Antwort

    If you have isopropyl alcohol on hand. You can use it to help weaken the adhesive temporarily when lifting up the adhered home button.

    Ben - Antwort

  23. Wenn du den Bereich um den Home Button/TouchID Sensor erwärmst, dann wird der Kleber weich, mit dem seine empfindlichen Kabel befestigt sind, so dass er leichter entfernt werden kann.
    • Wenn du den Bereich um den Home Button/TouchID Sensor erwärmst, dann wird der Kleber weich, mit dem seine empfindlichen Kabel befestigt sind, so dass er leichter entfernt werden kann.

    • Drehe die Displayeinheit herum. Nimm einen Haartrockner oder bereite einen iOpener vor und erwärme etwa 90 Sekunden lang die Unterkante des Displays, damit der Kleber darunter weich wird.

    If you don’t have that heating tool, a hair straightener n a T-shirt worked just fine for me

    www.tertlegerl - Antwort

  24. Schneide vorsichtig mit einem Plektrum durch den Kleber, der das Home / Touch ID Sensorkabel an der Rückseite des Displays hält. Schneide vorsichtig mit einem Plektrum durch den Kleber, der das Home / Touch ID Sensorkabel an der Rückseite des Displays hält. Schneide vorsichtig mit einem Plektrum durch den Kleber, der das Home / Touch ID Sensorkabel an der Rückseite des Displays hält.
    • Schneide vorsichtig mit einem Plektrum durch den Kleber, der das Home / Touch ID Sensorkabel an der Rückseite des Displays hält.

    It cannot be stressed enough that this is the one part of this repair that you can’t screw up. Anything else you’ll deal with during this repair can be easily replaced (The screen, and the sensor/microphone/camera assembly). Tearing this cable means an expensive trip to the apple store. or a very unhappy customer if you’re doing this for someone. Heat is your friend. I don’t even use a spudger or a guitar pick for this one, I use a new playing card to pull this up. Even with the card, you have to be careful. The edge of the playing card can nick the cable if you’re not careful to get it under the ribbon cable. If the adhesive isn’t soft enough for the card to get it up, apply more heat. Again, you can’t screw this step up. It’s all or nothing.

    Spartan99 - Antwort

    Well, no visible damage but the home button won’t work. I contacted a local Apple Authorized Service Center to check options. Since I had personally replaced the screen assembly, they wouldn’t even look at it per Apple policy. They said they would jeopardize their Apple Authorization if they even looked at it. Seems like more of the “Right to Repair” problem to me. Frustrated, but at least I have the accesibility home button working.

    bandman - Antwort

    Make sure the home button screws aren’t overtightened; that often causes issues. If there’s any damage to the button cable, a repair shop with a skilled microsolderer can patch a new cable on and restore functionality. iPhone 7 home button not working after screen replacement? Worst case scenario, you can also buy a screen repair from Apple, and they’ll include a new home button. I am not a lawyer, but the response you’re describing from the AASP sounds way out of bounds. Good luck!

    Jeff Suovanen -

    Just keep in mind that this is a very delicate step that requires a lot of patience. the part is attached to the body of the phone so firmly and there is no gap to put the opening pick under. So the way I did it was applying a good amount of heat onto the part and not from behind. I did it constantly for 5 minutes, a few minutes at a time, then I pulled the connected up slightly (a little too much pressure on the pull and you will break the wire). Pull it constantly and If the heat has been enough to melt the adhesive, it should come off easily and slowly.

    ashkan eslami fard - Antwort

    Hi, a little thing to help : i heatened up and then insert a cutter blade to start. Work better

    Crasset Renaud - Antwort

    Okay the home button is connected, as touch id works, but I can’t get any motion out of it. I backed off the screws, but that didn’t help. What else can I try?

    kathwick2 - Antwort

  25. Entferne die Home/Touch ID Sensoreinheit, indem du sie über die Vorderseite des Displays herausnimmst.
    • Entferne die Home/Touch ID Sensoreinheit, indem du sie über die Vorderseite des Displays herausnimmst.

    • Führe beim Zusammenbau zuerst das Kabel durch die Öffnung auf der Vorderseite des Displays.

    • Es kann sein, dass dein Ersatzteil mit einer zusätzlichen Y000 Schraube rechts vom Home Button ausgeliefert wurde. Diese Schraube ist überflüssig, entferne sie, so dass du die Halterung des Home Buttons wieder einbauen kannst.

    True to this picture, the home button can only be removed (and put back in place) through the front of the LCD assembly.

    Talon - Antwort

    Very good comment Talon. That was the first thing I was looking for here. There should be a bullet point in step 24 - Carefully remove home button from front of display being careful not to damage cable.

    Tracey - Antwort

    Had an issue when putting the screen back on, the side where the cables attach would not sit flush. At first I thought the cables were pushing the screen up. Turned out to be the battery cable shield was just a fraction too far down toward home button. After loosening screws, nudging it up slightly and screwing back in, the screen sat flush as it should. In case anyone else has same issue.

    jbarry - Antwort

    Is there anything special about reassembling the "home" button ?

    I tried several times with several buttons but none works.

    Lambiel - Antwort

    must use original button

    Christa -

    My phone is no more turning on after I replace the screen, no reaction if I press home button or power button

    cheryl.iseli - Antwort

    Why doesn’t this tutorial also cover the earpiece assembly?

    James - Antwort

    This guide is missing the camera transfer and the stupid little black sticker on the earpiece assembly that causes the earpiece not to work if that sticker is not transferred. This guide is wholly incomplete

    Mason Schild - Antwort

    James and @computermason—You’ll want to look up the correct guide for your repair, especially if you’re not using one of the kits for which this guide is designed. The guide for transferring all the smaller components is here.

    Jeff Suovanen - Antwort

    No home button functionality? I just watched a video on YouTube from two years ago saying that the iPhone 7 and 7+ have to be taken to an Apple repair center for the home button to work. Is this still the case? If so why didn’t you tell me this before I ordered this! Please confirm before I start warning everyone not to purchase from you!

    Gregory Haycock - Antwort

    @ghaycock If you’re replacing a screen, the home button will work fine as long as you carefully remove it from the old screen and transfer it to the new one, exactly as explained in the guide. The button itself can’t be replaced without help from Apple (which is why iFixit doesn’t sell home buttons for this model).

    Jeff Suovanen -

    One thing I don’t see mentioned is the replacement of the rubber gaskets that are on the pentalobe holes. The replacement screen did not come with these on it. I was able to remove them from the OEM screen, but there was no easy way to get them to adhere to the new screen. If they move just a little, you might not be able to properly thread the pentalobe screws. Worst case is that they fall into the body of the phone during this last step of re-assembly. At that point, you’ve already started to have the screen stuck to the adhesive, so you would need to redo the entire adhesive gasket.

    You can see the gaskets in this picture: https://d3nevzfk7ii3be.cloudfront.net/ig...

    Here they are near the new screen: https://drive.google.com/open?id=14FwpSB...

    Andre LeBlanc - Antwort

  26. Löse die drei Kreuzschlitz Schrauben, welche die Abdeckung des Ohrhörer-Lautsprechers mit dem Display verbinden
    • Löse die drei Kreuzschlitz Schrauben, welche die Abdeckung des Ohrhörer-Lautsprechers mit dem Display verbinden

    • Zwei 2,6 mm Schrauben

    • Eine 1,7 mm Schraube

    I am measuring the screws; my digital caliper measures both the top at 1.88mm not 2.6

    Marco Cueva - Antwort

    I just checked the screw measurements and they match what’s shown in the guide. Are you sure you’re looking at the right screws?Are you sure your caliper is accurate? Was your iPhone serviced in the past and reassembled incorrectly? Something isn’t right. The measurements here are the screw lengths, by the way—just in case you were measuring something else.

    Jeff Suovanen -

  27. Entferne die Abdeckung des Ohrhörer-Lautsprechers.
    • Entferne die Abdeckung des Ohrhörer-Lautsprechers.

  28. Entferne die Frontkamera, um an den Ohrhörer-Lautsprecher zu gelangen. Entferne die Frontkamera, um an den Ohrhörer-Lautsprecher zu gelangen.
    • Entferne die Frontkamera, um an den Ohrhörer-Lautsprecher zu gelangen.

  29. Entferne die folgenden beiden Kreuzschlitz Schrauben, welche den Ohrhörer-Lautsprecher mit dem Display verbinden:
    • Entferne die folgenden beiden Kreuzschlitz Schrauben, welche den Ohrhörer-Lautsprecher mit dem Display verbinden:

    • Eine 1,9 mm Schraube

    • Eine 2,5 mm Schraube

    Hi!What size is the third screw?

    Лёха Н - Antwort

  30. Entferne jetzt den Ohrhörer-Lautsprecher.
    • Entferne jetzt den Ohrhörer-Lautsprecher.

  31. Erhitze erneut deinen iOpener und lege ihn auf den oberen Rand der Display Einheit, um den Kleber zu lösen, welcher die Frontkamera und die Sensoreinheit fixiert.
    • Erhitze erneut deinen iOpener und lege ihn auf den oberen Rand der Display Einheit, um den Kleber zu lösen, welcher die Frontkamera und die Sensoreinheit fixiert.

    • Warte mindestens 2 Minuten bevor du mit dem nächsten Schritt weitermachst, damit der Kleber genug Zeit hat, weich zu werden.

  32. Verwende einen Spudger, um den Umgebungslichtsensor vorsichtig aus seiner Vertiefung auf dem Front Panel herauszuhebeln. Versuche dein Werkzeug ganz unter den Sensor zu schieben um es von dem durchsichtigen Plastikteil darunter abzulösen. Wenn du nur gegen das Kabel hebelst, dann kann sich der Sensor von der Kabeleinheit lösen und muss dann ausgewechselt werden. Wenn du sowieso die Sensor/Kabeleinheit austauschen willst, spielt das natürlich keine Rolle.
    • Verwende einen Spudger, um den Umgebungslichtsensor vorsichtig aus seiner Vertiefung auf dem Front Panel herauszuhebeln.

    • Versuche dein Werkzeug ganz unter den Sensor zu schieben um es von dem durchsichtigen Plastikteil darunter abzulösen. Wenn du nur gegen das Kabel hebelst, dann kann sich der Sensor von der Kabeleinheit lösen und muss dann ausgewechselt werden. Wenn du sowieso die Sensor/Kabeleinheit austauschen willst, spielt das natürlich keine Rolle.

    I’m sorry to comment but this step is wrong. The proximity sensor is sticked to the display. I was following this instruction and the sensor was unvelded from the flex cable. Now it’s workless. It’s a fortune that the only problem with the iPhone is that while calling and holding the phone to the ear, the display doesn’t turn off.

    I recommend to gently pushing against the transparent plastic enclosure near the sensor and once it’s unsticked, keep pushing against the sensor’s body. In this way the sensor welding doesn’t bear/support any extra load on it.

    At least, my iPhone 7G had the sensor sticked to the display. Maybe some day I will replace it (around 20€ - 25€ on ebay)

    I won't claim to iFixit nor stop using this website. Whenever I higly recommend to iFixt technitians to revise such kind of “errors”. At least for expensive devices like Apple products.

    Miguel Cretu - Antwort

    I editted this guide and added these two comments. I already know about this “trick”. It’s your own decision to follow my suggestion or not.

    Miguel Cretu - Antwort

    I have fixed 2 screens now on iPhone 7. The 1st time I didn’t have this problem, 2nd time I did. I would agree with Miguel Cretu and save yourself the hassle and remove the sensor and it’s surround altogether.

    Wayne Lyell - Antwort

    In the second picture, there is the splugger that’s on it’s right is near a little window square, white inside. I’ve checked my replacement display and it don’t have inside in WHITE in this little window . Anyone know why have this color (it is not a sticker) and what is the reason? Thanks

    fakirox - Antwort

  33. Schiebe nun das Plektron Richtung Kameragehäuse und trenne so den Kleber, der das Kabel am Front Panel festhält. Stoppe kurz vor dem Gewinde. Schiebe nun das Plektron Richtung Kameragehäuse und trenne so den Kleber, der das Kabel am Front Panel festhält. Stoppe kurz vor dem Gewinde. Schiebe nun das Plektron Richtung Kameragehäuse und trenne so den Kleber, der das Kabel am Front Panel festhält. Stoppe kurz vor dem Gewinde.
    • Schiebe nun das Plektron Richtung Kameragehäuse und trenne so den Kleber, der das Kabel am Front Panel festhält. Stoppe kurz vor dem Gewinde.

  34. Nutze nun das Plektron, um das Kamerakabel von den beiden Kunststoffnippeln auf dem Front Panel zu lösen und es von den letzten Kleberesten zu befreien. Nutze nun das Plektron, um das Kamerakabel von den beiden Kunststoffnippeln auf dem Front Panel zu lösen und es von den letzten Kleberesten zu befreien. Nutze nun das Plektron, um das Kamerakabel von den beiden Kunststoffnippeln auf dem Front Panel zu lösen und es von den letzten Kleberesten zu befreien.
    • Nutze nun das Plektron, um das Kamerakabel von den beiden Kunststoffnippeln auf dem Front Panel zu lösen und es von den letzten Kleberesten zu befreien.

    на рисунке №2 винт 3 отсутствует, на рисунке № 3 винт 3 присутствует. нет описание где он был вывинчен. последний винт с правой стороны, около камеры

    Vitaly Savin - Antwort

  35. Entferne die Frontkamera und das Sensorkabel.
    • Entferne die Frontkamera und das Sensorkabel.

    Look at the camera assembly closely. There are two cables soldered together. Do not separate the pieces by mistake . Get the pick all the way below both ,and they will come off together.

    turboduck2 - Antwort

    Good statement I made that mistake on my first iPhone 7 Plus !

    Jaye - Antwort

    Its not mentioned here but there is a small philips screw at the top left that you may have to transfer to your new lcd panel

    Steve - Antwort

    Hi Steve, what is the main work of this little strip with 2 small contact? Antenna? Shield?

    Thanks

    fakirox -

    I’ve separated the sensor and front facing camera, can I just press them back together or will I need a complete replacement

    Dominic Sore - Antwort

    About Steve comment, anyone know what is this small screw with two contact? It is an antenna ?? Shield??? Thanks

    fakirox - Antwort

    I’m also looking for info on the screw on the immediate left of the top left corner of the speaker. Did you find the info out?

    Cheers!

    Mike Grandbois - Antwort

  36. Entferne die drei 1,2 mm Tri-point Y000 Schrauben auf jeder Seite der Displayeinheit, also insgesamt sechs Schrauben. Entferne die drei 1,2 mm Tri-point Y000 Schrauben auf jeder Seite der Displayeinheit, also insgesamt sechs Schrauben.
    • Entferne die drei 1,2 mm Tri-point Y000 Schrauben auf jeder Seite der Displayeinheit, also insgesamt sechs Schrauben.

    i miss the screw size here

    Beerbo - Antwort

    I think it's 1.2mm Y000

    STRAP -

    I d’ont think the screw size is correct, because i had to order a new heat shield plate, because my original broke during the replacement.

    Marco Burkhalter - Antwort

    I found if I held the flat end of a spudger behind the screw while I unscrewed, it worked well. Otherwise there was too much flex to get a good grip on the screw.

    Travis Hogg - Antwort

    good tip! Yes, there is indeed too much flex when removing the screws.

    amberron -

    My screws are too tight that I can't unscrew it. What should I do?

    Charles Bejarano - Antwort

    I have had this problem so far on all the red tri point screws. The first screw, the home button, and 4/6 of these. I have noticed little to no advice on each one or for stripped screws. I have been able to manage so far but not sure about this one.

    kimberly klassy -

    Here, I was able to use a soldering iron on the back side of the screw to get it quite hot to release the INSANE amount of loctite that was applied to my 7. Be patient and let the screw get hot. If you try to move the screw with the Y000 and it doesn’t move, WAIT. Don’t strip the screw or your driver.

    P Park - Antwort

    Good tip using the soldering iron. I’ve just ordered a quality Y driver as the cheap one that came with the screen can’t remove these screws. Why the the Loctite? Had to reassemble what I’ve pulled apart to await the new driver.

    Tony Binstead -

    I understand home button , but why do i need to replace the shield and camera/speaker?

    Ēriks Jaunzems - Antwort

  37. Erhitze einen iOpener und lege ihn auf die Kante des Abschirmblechs, die dem Home Button am nächsten ist, um den Klebstoff zu aufzuweichen.
    • Erhitze einen iOpener und lege ihn auf die Kante des Abschirmblechs, die dem Home Button am nächsten ist, um den Klebstoff zu aufzuweichen.

  38. Benutze ein Opening Pick (Plektrum), um den Kleber, der neben dem Home Button das LCD Abschirmblech an der Displayeinheit befestigt, zu lösen. Benutze ein Opening Pick (Plektrum), um den Kleber, der neben dem Home Button das LCD Abschirmblech an der Displayeinheit befestigt, zu lösen. Benutze ein Opening Pick (Plektrum), um den Kleber, der neben dem Home Button das LCD Abschirmblech an der Displayeinheit befestigt, zu lösen.
    • Benutze ein Opening Pick (Plektrum), um den Kleber, der neben dem Home Button das LCD Abschirmblech an der Displayeinheit befestigt, zu lösen.

    applying 1 minute of hair dryer heat in this step really helps the separation in this step

    amberron - Antwort

    definitely use heat and work slowly!

    Catharine - Antwort

  39. Hebe vorsichtig das LCD Abschirmblech von der Displayeinheit ab. Achte darauf, dass die Displaydatenkabel nicht dabei hängen bleiben.
    • Hebe vorsichtig das LCD Abschirmblech von der Displayeinheit ab.

    • Achte darauf, dass die Displaydatenkabel nicht dabei hängen bleiben.

  40. Nur das LCD inklusive Touchscreen bleiben übrig.
    • Nur das LCD inklusive Touchscreen bleiben übrig.

Abschluss

Um dein Gerät wieder zusammenzubauen, folge diesen Schritten in umgekehrter Reihenfolge.

323 weitere Nutzer haben diese Anleitung absolviert.

Besonderer Dank geht an diese Übersetzer:

100%

Diese Übersetzer helfen uns, die Welt in Ordnung zu bringen! Wie kann ich mithelfen?
Beginne zu übersetzen ›

Evan Noronha

Mitglied seit: 05.02.2015

175.717 Reputation

177 Anleitungen geschrieben

Team

iFixit Mitglied von iFixit

Community

104 Mitglieder

9.248 Anleitungen geschrieben

When I took off the home button, a small black square rubber piece fell out. while prying off the cable.

Can anyone tell me where this is supposed to go when I put the home button back on.

Joe in PA - Antwort

The small black square that fell off is originally located on the bottom pentalobe screw bracket on the screen. It can slide back over it if you place it right.

Primus -

Thank you!!!

Punxohn Khut -

useless guide without a guide how to mount it all back on.

The home button wont fit back in its whole

iffbas - Antwort

You have to put the flex through the hole from the front, and set the button against the front of the screen. Just like you got it out, in reverse.

Eric Davies -

The home button is a very delicate assembly. Once you have the home button's cable off the back of the display, and the screws off, push it lightly out from the back of the display. It should fall out.

michelle mcdonald - Antwort

Would be nice to show the process of making it watertight again.

Justin - Antwort

I have tried to fit 2 different lcd’s to an iphone 7 and the phone keeps going to apple logo and then black but when I disconnect the home button the phone load up

jamesreid1958 - Antwort

There was an apple update that fixed that issue, it was update that caused the crash

CPR Fredericksburg -

I have completed the screen repair, although now the iPhone takes minutes to boot up and then keeps freezing when trying to use it. I have connected the old screen just in case it’s the new screen that’s the issue although it still appears to be the same. Also now when I connect the camera flex at the top the iPhone just boot loops. I have also tried a new Camera flex with the same result. Can anyone help with either of these problems?

Donald - Antwort

When reassembling the home sensor and the front camera without using any adhesive, how will that affect the end result? Or is it implicit that you should use adhevise of some sort when reassembling?

Per Helm - Antwort

How do i get adhesive to make the phone waterproof again and where can I get a good lcd to replace my damaged one

Iyinoluwa Ayedegbe - Antwort

Hi, you can find a new LCD here, and new adhesive here. Replacing the adhesive won’t guarantee that the phone is waterproof again, but it certainly helps.

Adam O'Camb -

It has been mentioned here through virtue of the fact that Joe in PA queried what the rubber grommets were for after prying off the home button ribbon cable, if this is for a replacement LCD it might be worth adding a step advising that these need to be removed carefully by sliding them up and off the pentalobe screw brackets with tweezers as they’ll need to be moved across to the replacement screen, 3rd party replacements don’t come with them fitted.

Brendon Gould - Antwort

With a little time and patience, I switched out the lcd screen. My only issues are that even though i used the same home button, the finger print feature no longer works and the screen is way to sensitive that it has to be put on speaker phone for calls because my cheek touches the phone. i’ve been trying to find out if there is an adhesive that is supposed to be on the back of the lcd screen when i reassembled it or anything else i can do to remedy this frustrating issues.

Stacy Mails - Antwort

Is your screen illuminated while you talk? If so, the proximity sensor may not be seated properly, or broken. Trying to understand what you mean by the screen being too sensitive.

daimodess -

If I am harvesting another iPhone 7 for parts, do I need to remove everything from the screen? I know I need to move the home button for touch ID, but can I just leave other things like the front facing camera alone, or are those tied to the logic board too?

d0rk4l - Antwort

The home button’s Touch ID is the only thing that’s tied to the logic board. All the other small parts on the screen can be freely replaced or moved to another iPhone 7 and will retain functionality.

Adam O'Camb -

HELP strange situation. Bought an iPhone 7 stuck in a boot loop and cracked screen. Home button working fine. Fixed boot loop, restored- but after swapping the home button across to the new screen I’m finding the home button has stopped working. The home button still works fine from the old cracked screen... I thought the home button was married to the logic board? Any advice??

titcharoony123 - Antwort

Help please.

have changed it all out and it will not power on at all what is wrong with it

William Feltner - Antwort

I changed an iPhone 7 screen and I Get no display coming up. All connectors are plugged in properly. Help

Jerry Ramirez - Antwort

Installing the adhesive gasket was easy to figure out, however, the instructions on re-assembly should say something about it instead of ignoring it. C’mon, man!

jlauve - Antwort

There are extensive instructions linked in Step 19.

Jeff Suovanen -

I just want to comment that I LOATHE Apple for adding these Y000 screws.

Make sure you get a good Y000 screwdriver, because the crappy one that came with the replacement screen (purchased from Amazon. Sorry iFixit, the person didn’t want to spend the extra money to go with your screen) started to strip when I tried to remove the first few Y000 screws.

I had to keep filing down the screwdriver in order to use it.

Joe - Antwort

Hi. Any solution to fix Toich ID not working.

Deniss Ko - Antwort

So I work at a phone repair shop and went to replace the screen on my iPhone 7 today, and i accidentally grabbed an iPhone 8 screen. To my surprise it works, i don’t see any difference but i’m going to switch it out just to be safe. True tone doesn’t work either ;(

Zachary Larkin - Antwort

I have just recently changed my lcd screen on my phone and it would turn on but then when it gets to the home screen it would turn black while still on. I know its on because I could have siri call people up and it would work but I just cant see anything. Help pls!

maria noy - Antwort

Home button is going to work or not? you guys got me all confused saying is tied to the logic board, but that i need to change it to make touch id to work on the new screen, so what a !&&*? :(

carloscaste - Antwort

You need to keep your original home button and transfer it carefully to the new display, exactly as stated in the guide. If you do that correctly, everything will work fine. You can safely ignore any commenters claiming otherwise; this is how it has worked ever since Touch ID first came out on the iPhone 5s.

Jeff Suovanen -

I used this screen to repair an iPhone 7 and the home button stopped working completely a week after the repair.

Casey Mills -

Hi,

Who had problems with four Y000 screws securing the bracket over the home/Touch ID sensor and three 1.2mm tri-point Y000 screws from either side of the display assembly ? They do not get out and break.

andreyshtepa888 - Antwort

Hello, i repaired the phone and after it would turn on but after awhile it would just start turning off randomly and wont charge past %16 what happened?

Parker Wruck - Antwort

Back camera not working after screen replacement. The front camera and sensor are ok. What could have happened?

Ida W - Antwort

Just completed the replacement and my phone won’t seem to power back on. Double checked the battery connection and the other connections without any results. Any idea where I may have gone wrong? Not sure if it matters but when the screen broke it pressed buttons non stop and locked itself out until connected to iTunes.

Thanks in advnce!

Eric Davis - Antwort

I installed a new display on an iPhone 7 because the original display was horribly cracked. The new display was functioning perfectly but after a few days, the digitizer stopped responding to any touch. I installed a second display and the problem went away, until a couple days later; when the digitizer stopped recognizing any touch again. Any thoughts as to why this is happening?

Nacho Camacho - Antwort

I’ve ordered 2 replacement kits from different companies and both came with an orange translucent sticker on the back of the screen. What is this for? Do I just remove it and toss it?

Also there's a little blue translucent plastic thing near the camera and sensors. Is this also just temporary for shipping?

Thirdly the screen ribbon cables cause the lcd shield to bulge up. This made it difficult to press the phone back together.

Do I squish it into submission?

Darren Jones - Antwort

@oldman_winter Those plastic stickers/liners are for temporary protection during stocking and shipping and should be removed. As for the cables, if manufactured and installed correctly, they shouldn’t be causing any bulges. Compare carefully with the original part and make extra sure you have the correct part for your specific model.

Jeff Suovanen -

After change display NFC doesn’t work. Can anybody help with this situation?

Антон Шорин - Antwort

there are 2 clear plastic mounts, 1 for the camera and 1 for the light sensor that need to be gently pryed off and re attached to the replacement screen if they are not on there already…. i used a TINY dab of super glue for this!!

Mark Burnett - Antwort

Kommentar hinzufügen

Statistik anzeigen:

Letzte 24 Stunden: 125

Letzte 7 Tage: 1,193

Letzte 30 Tage: 4,782

Insgesamt: 287,299