Zum Hauptinhalt wechseln

iPhone 7 Logic Board Disconnection

Grundständige Anleitung
Dies ist eine grundständige Anleitung, die nur als Teil einer anderen Anleitung verwendet werden sollte.

Was du brauchst

  1. iPhone 7 Logic Board  Disconnection, Logic Board Connectors: Schritt 1, Bild 1 von 2 iPhone 7 Logic Board  Disconnection, Logic Board Connectors: Schritt 1, Bild 2 von 2
    • Use the flat end of a spudger to disconnect the rear-facing camera connector.

  2. iPhone 7 Logic Board  Disconnection: Schritt 2, Bild 1 von 2 iPhone 7 Logic Board  Disconnection: Schritt 2, Bild 2 von 2
    • Remove the following Phillips screws securing the rear camera bracket to the rear case:

    • One 1.3 mm screw

    • One 2.5 mm screw

  3. iPhone 7 Logic Board  Disconnection: Schritt 3, Bild 1 von 1
    • Remove the bracket.

  4. iPhone 7 Logic Board  Disconnection: Schritt 4, Bild 1 von 2 iPhone 7 Logic Board  Disconnection: Schritt 4, Bild 2 von 2
    • Use the pointed end of a spudger to pry up and disconnect the antenna bus connector, just left of the rear camera module.

  5. iPhone 7 Logic Board  Disconnection: Schritt 5, Bild 1 von 1
    • Remove the two 1.2 mm tri-point screws securing the upper cable bracket.

  6. iPhone 7 Logic Board  Disconnection: Schritt 6, Bild 1 von 2 iPhone 7 Logic Board  Disconnection: Schritt 6, Bild 2 von 2
    • Remove the upper cable bracket.

  7. iPhone 7 Logic Board  Disconnection: Schritt 7, Bild 1 von 2 iPhone 7 Logic Board  Disconnection: Schritt 7, Bild 2 von 2
    • Use the flat end of a spudger to disconnect the upper cable connector.

  8. iPhone 7 Logic Board  Disconnection: Schritt 8, Bild 1 von 2 iPhone 7 Logic Board  Disconnection: Schritt 8, Bild 2 von 2
    • Remove the Phillips screws securing the Wi-Fi antenna:

    • Three 1.2 mm screws

    • One 1.7 mm screw

  9. iPhone 7 Logic Board  Disconnection: Schritt 9, Bild 1 von 2 iPhone 7 Logic Board  Disconnection: Schritt 9, Bild 2 von 2
    • Remove the top left antenna.

  10. iPhone 7 Logic Board  Disconnection: Schritt 10, Bild 1 von 1
    • Remove the following Phillips screws:

    • One 1.3 mm screw

    • One 2.2 mm screw

  11. iPhone 7 Logic Board  Disconnection: Schritt 11, Bild 1 von 2 iPhone 7 Logic Board  Disconnection: Schritt 11, Bild 2 von 2
    • Remove the bracket.

  12. iPhone 7 Logic Board  Disconnection: Schritt 12, Bild 1 von 1
    • Remove the 2.2 mm standoff screw from the grounding bracket.

    • Standoff screws are best removed using an [verlinktes Produkt fehlt oder ist deaktiviert: IF145-343] and driver handle.

    • In a pinch, a small flathead screwdriver will do the job—but use extra caution to ensure it doesn't slip and damage surrounding components.

  13. iPhone 7 Logic Board  Disconnection: Schritt 13, Bild 1 von 2 iPhone 7 Logic Board  Disconnection: Schritt 13, Bild 2 von 2
    • Use tweezers to gently bend the logic board grounding bracket out of the way.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Evan Noronha

Mitglied seit: 02/05/15

223.223 Reputation

168 Anleitungen geschrieben

0 Kommentare

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 0

Letzte 7 Tage: 0

Letzte 30 Tage: 0

Insgesamt: 184