Zum Hauptinhalt wechseln

iPhone X Taptic Engine austauschen

Was du brauchst

  1. iPhone X Taptic Engine austauschen, Pentalobe Schrauben: Schritt 1, Bild 1 von 1
    • Bevor du anfängst, sollte der Akku deines iPhones auf unter 25% entladen sein. Ein geladener Lithium-Ionen Akku kann Feuer fangen und/oder explodieren, wenn er beschädigt wird.

    • Schalte dein iPhone aus, bevor du daran arbeitest.

    • Drehe die beiden 6,9 mm langen Pentalobe Schrauben an der unteren Kante heraus.

    • Wenn die Schrauben beschädigt sind, musst du sie ersetzen.

    • Wenn du ein iPhone öffnest werden seine wasserfesten Dichtungen beschädigt. Halte Ersatzdichtungen bereit, bevor du nach diesem Schritt weitermachst, oder vermeide es, dein iPhone der Feuchtigkeit auszusetzen, wenn du es ohne neue Dichtungen wieder zusammenbaust.

    There are 6.81mm long screws!

    Daniel - Antwort

    One of the pentalobe screws is stripped :( - suggestions for how to get it out?

    cgtyoder - Antwort

    same situation here

    kaunomarcius - Antwort

    Same issue for me too, how do I get the stripped screw out?

    patronics - Antwort

    Update: I was able to get the “stripped” screw out using another Pentalobe-2 screwdriver bit from another company. It seems it wasn’t the screw, but the screw driver that was actually stripped. Hence why the other screwdriver kit I got came with 3 of this bit, I suppose.

    patronics - Antwort

    I ended up going to a jewelry store, and they drilled down into the screw, with of course an incredibly tiny bit. That allowed me to insert the P2 driver, and I was able to unscrew it at that point. Good luck!

    cgtyoder - Antwort

    Same issue with the stripping. The tip of the iFixit P2 head in my $70 kit just ground off on the first screw and that was that. Not much you can do.

    Kyle Harris - Antwort

    yes correct the same happened to me, the screws were perfect shaped never been open and as soon as i used the P2 it stripped the screws, seems like the P2 is slightly smaller but Dremel kit with a very small drill bits and precise knife tool is the way to go.

    Dulce Vidal - Antwort

    This step in automatically followed through, without any thought. Why remove these screws? Can anybody explain? The Screen is detachable all the same, with them well screwed in…

    Uri - Antwort

    These screws attach to a plate that’s part of the screen half of the phone. If you succeed in detaching the screen without removing those, it would seem reasonable that you will have damaged that plate or its ability to keep the two halves together.

    Dan Long -

    @Dan Long is right

    Uri -

    Clean out the pentalobe screw heads first so the tool goes all the way in. A small sewing needle works well to loosen any build up and then press some putty/chewing gum into the screw head and pull away quickly for a final clean out.

    William Olstad - Antwort

    The this kit should include screws because you’re going to strip them. Can’t even get past step one. Did anybody figure this out

    justin - Antwort

    Never opened my phone ever, when I went to look at the first step.. I noticed one of my screws was stripped. I thought it was impossible, but I removed the non stripped one, then once I got to the stripped one.. I learned my assumptions were correct. I bought this one straight from the apple site years ago ahaha Any tips to remove the stripped screw?

    Clarence Williams - Antwort

    William Olstad's tip about cleaning the screws with a needle and a bit of poster putty worked well for me. There was a lot of crud in there! The opening is shallow, so it's easy to see how the screwdriver wouldn't catch with even a bit of grit in the way, No problem getting the pentalobe screws out with the ifixit screwdriver.

    punkinann - Antwort

    If all else fails, very carefully cut a slot across the head of the screw with a Dremel tool using a diamond bit that dentist will gladly give you - I ask my dentist for used bits; and chuck them in a drill bit chuck designed for Dremel. The slot allows you to use a tiny, straight blade screwdriver. You can reuse the screw or replace it with a new pentalobe screw.

    Dan Smith - Antwort

  2. iPhone X Taptic Engine austauschen, Gesplittertes Glas überkleben: Schritt 2, Bild 1 von 3 iPhone X Taptic Engine austauschen, Gesplittertes Glas überkleben: Schritt 2, Bild 2 von 3 iPhone X Taptic Engine austauschen, Gesplittertes Glas überkleben: Schritt 2, Bild 3 von 3
    • Wenn die Glasscheibe des Displays an deinem iPhone zerbrochen ist, überklebe sie mit geeignetem Klebeband, um weitere Brüche und Verletzungen während der Reparatur zu vermeiden.

    • Überdecke die Glasscheibe des Displays komplett mit überlappenden Streifen von durchsichtigem Paketband.

    • Trage eine Schutzbrille, um deine Augen vor Glassplittern zu schützen.

    • Wenn das Glas so stark zerbrochen ist, dass der Saugheber in den nächsten Schritten nicht gut haftet, dann versuche ein starkes Klebeband ("Panzerband") zu einem Griff zu falten und so auf die Scheibe zu kleben, dass du sie damit hochziehen kannst.

    • Wenn das alles nicht hilft, dann klebe den Saugheber mit Sekundenkleber am Display fest.

  3. iPhone X Taptic Engine austauschen, Anleitung für die Anti-Clamp: Schritt 3, Bild 1 von 3 iPhone X Taptic Engine austauschen, Anleitung für die Anti-Clamp: Schritt 3, Bild 2 von 3 iPhone X Taptic Engine austauschen, Anleitung für die Anti-Clamp: Schritt 3, Bild 3 von 3
    • Wir haben die Anti-Clamp entwickelt, um das Öffnen von Geräten zu erleichtern. Die nächsten drei Schritte zeigen, wie sie verwendet wird. Wenn du sie nicht benutzen willst, überspringe die nächsten drei Schritte und folge einer anderen Methode.

    • Genaue Anweisungen für die Anti-Clamp findest du hier.

    • Drücke den blauen Griff zurück, damit die Arme der Anti-Clamp frei beweglich werden.

    • Schiebe die Arme entweder über die linke oder die rechte Kante des iPhones.

    • Bringe die Saugheber nahe an der Unterkante des Displays an, einen auf der Vorderseite, den anderen auf der Rückseite.

    • Drücke die Saugheber zusammen, so dass sie auf den Oberflächen haften.

    • Wenn die Saugheber nicht gut auf den Oberflächen des iPhones haften, dann kannst du Klebeband verwenden, um eine griffigere Oberfläche zu schaffen.

  4. iPhone X Taptic Engine austauschen: Schritt 4, Bild 1 von 3 iPhone X Taptic Engine austauschen: Schritt 4, Bild 2 von 3 iPhone X Taptic Engine austauschen: Schritt 4, Bild 3 von 3
    • Drücke den blauen Griff vorwärts, um die Arme wieder zu verriegeln.

    • Drehe den Griff eine volle Umdrehung im Uhrzeigersinn, oder bis du merkst, dass sich die Saugheber dehnen.

    • Achte darauf, dass sich die Saugheber weiterhin gegenüber stehen. Wenn sie sich nicht mehr gegenüber stehen, dann löse die Saugheber ein wenig ab und schiebe sie in die richtige Position.

  5. iPhone X Taptic Engine austauschen: Schritt 5, Bild 1 von 3 iPhone X Taptic Engine austauschen: Schritt 5, Bild 2 von 3 iPhone X Taptic Engine austauschen: Schritt 5, Bild 3 von 3
    • Führe einen erwärmten iOpener durch die Arme der Anti-Clamp.

    • Du kannst den Kleber auch mit einem Haartrockner oder einem Heißluftgebläse aufweichen. Sei aber vorsichtig, zu viel Hitze kann das Display und/oder den Akku beschädigen.

    • Forme den iOpener so, dass er auf der Unterkante des iPhones liegt.

    • Warte eine Minute, damit sich der Kleber lösen und ein Spalt entstehen kann.

    • Setze ein Plektrum in den Spalt unter das Display und der Kunstoffblende ein, nicht unter das Display selbst.

    • Wenn es nicht gelingt, mit der Anti-Clamp einen ausreichend großen Spalt zu erzeugen, dann erwärme die Stelle nochmals und drehe den Griff eine viertel Umdrehung im Uhrzeigersinn weiter.

    • Drehe den Griff jeweils nicht mehr als eine viertel Umdrehung weiter und warte jedes Mal eine Minute lang. Gib der Anti-Clamp Zeit, ihre Arbeit zu erledigen.

    • Überspringe die nächsten drei Schritte.

    DO NOT separate the glass from the plastic bumper or rim around it. These instructions don't clarify that the pick has to be inserted between the plastic rim and the metal body. It is likely that the glass will lift slightly off the plastic surround before the plastic will lift out of the metal body. I had success sliding a card or pick back and forth along the bottom edge of the plastic rim while pulling on the suction cup. Eventually there was a space large enough for the pick to go under the plastic rim.

    Anessa - Antwort

    Thanks for pointing this out! I'll revise this step to clarify this point.

    Arthur Shi -

  6. iPhone X Taptic Engine austauschen: Schritt 6, Bild 1 von 1
    • Das Öffnen des iPhones wird leichter, wenn du seine Unterkante erwärmst und damit den Kleber darunter aufweichst.

    • Benutze einen Haartrockner oder ein Heißluftgebläse oder bereite unseren iOpener vor. Erwärme damit die Unterkante des iPhones etwa eine Minute lang, um den Kleber darunter aufzuweichen.

    General tip regarding heating necessary to remove adhesive:

    consider using a heated tip of a small screwdriver or metal spudger (not the one made of plastic, provided in kit), rather than to heat the device itself.

    Uri - Antwort

    You then need to be careful about the temp of the tool which if hot enough can melt plastic components or harm them. Keeping the heat source (heat gun) far enough away from the object that you’ll eventually melt the glue but would be much harder to melt components. I try to keep 4” or 5” gap between the source & object

    Sandman619 -

    Thanks for the info. Could a air convector do the job

    dominique.br - Antwort

    When opening a device that has previously been worked on, and on which the adhesive might not have been replaced, be extremely carful when opening the phone. It will open much more easily than expected. If you’re not careful you might rip a cable.

    jonpol - Antwort

    Is this tool required or can I just use the Anti-Clamp by itself.

    Mikail - Antwort

    If you have a 3d printer, heat the bed to 80c and put the phone screen side down on it for 30 secs

    philip.joseph123 - Antwort

  7. iPhone X Taptic Engine austauschen: Schritt 7, Bild 1 von 2 iPhone X Taptic Engine austauschen: Schritt 7, Bild 2 von 2
    • Wenn du einen einzelnen Saugheber benutzt, dann setze ihn am unteren Rand des iPhone auf, wobei du den gebogenen Teil des Bildschirms vermeiden musst.

    If you were using some form of screen protector, it may come off first as soon as you pull on the suction cup. Do not be alarmed. That is normal behavior.

    Alain-Daniel Wa-Baguma - Antwort

    3m VSB double stick tape will stick to the screen when the suction cups fail (see my comment on step 1)

    Tawan Khamapirad - Antwort

  8. iPhone X Taptic Engine austauschen: Schritt 8, Bild 1 von 3 iPhone X Taptic Engine austauschen: Schritt 8, Bild 2 von 3 iPhone X Taptic Engine austauschen: Schritt 8, Bild 3 von 3
    • Ziehe fest und gleichmäßig am Saugheber und erzeuge dadurch einen kleinen Spalt zwischen Display und Rahmen.

    • Setze ein Plektrum in den Spalt unter der Kunstoffblende am Display ein, nicht am Display selbst.

    • Der wasserfeste Kleber, der das Display festhält, ist sehr stark. Um den anfänglichen Spalt zu erzeugen, musst du recht viel Kraft aufbringen. Wenn der Spalt schwer zu öffnen ist, musst du mehr Wärme anwenden. Bewege die Scheibe vorsichtig hoch und runter und löse so den Klebstoff, bis der Spalt groß genug ist, um das Werkzeug einzusetzen.

    In addition to safety goggles, I would recommend you also wear good gloves to avoid getting cut with the glass as you try to pry it open.

    Alain-Daniel Wa-Baguma - Antwort

    The top about applying more heat and gently rocking the screen up and down to weaken the adhesive did the trick for me. Thank you!

    Monil Shah - Antwort

    There needs to be more clarity on where to shove the opening pick into. There is actually two openings that the pry tool can be forced into: one below the black plastic bezel, and one above the black plastic bezel. When I heated my screen with a warming pad and pulled up the suction cup, it actually pried apart above the black plastic bezel which removed the touch screen from the display panel. With this being the first newer iPhone I'd opened since the 3GS, I didn't realize that I was opening the wrong opening as the directions only mentioned one opening and did not warn of this. I was pretty disappointed in the lack of mentioning this, as I was taking my time and following it to the tee. As a result, it destroyed my original iPhone screen.

    Caleb Davison - Antwort

    DO NOT separate the glass from the plastic bumper or rim around it. As someone else noted, these instructions don't clarify that the pick has to be inserted between the plastic rim and the metal body of the phone. When pulling upwards with the suction cup, it is likely that the glass will lift slightly off the plastic surround before the plastic will lift out of the metal body. I had success sliding a card or pick back and forth along the bottom edge of the plastic rim while pulling on the suction cup. Eventually there was a space large enough for the pick to go under the plastic rim.

    Anessa - Antwort

    Thank you for pointing this out! I've updated the step to reflect this.

    Arthur Shi -

    The suction cup doesn't work at all... The minimum force I apply to lift it up, it comes off completely. This is very frustrating!!!

    Mario Silva - Antwort

  9. iPhone X Taptic Engine austauschen: Schritt 9, Bild 1 von 3 iPhone X Taptic Engine austauschen: Schritt 9, Bild 2 von 3 iPhone X Taptic Engine austauschen: Schritt 9, Bild 3 von 3
    • Schiebe das Plektrum um die linke untere Ecke und am linken Rand des iPhone hoch, zerschneide damit den Kleber, der das Display festhält.

    • Setze das Plektrum nicht tiefer als 3 mm in das iPhone ein, damit du keine internen Bauteile beschädigst.

  10. iPhone X Taptic Engine austauschen, Informationen zum Display: Schritt 10, Bild 1 von 1
    • An der rechten Kante des iPhones verlaufen empfindliche Kabel. Setze an diesen Stellen kein Plektrum ein, du könntest sonst die Kabel beschädigen.

    Wouldn’t it be better to put this part BEFORE the step where you have to pry open the phone?

    Jan D. Höllwarth - Antwort

  11. iPhone X Taptic Engine austauschen: Schritt 11, Bild 1 von 3 iPhone X Taptic Engine austauschen: Schritt 11, Bild 2 von 3 iPhone X Taptic Engine austauschen: Schritt 11, Bild 3 von 3
    • Setze da Plektrum wieder an der Unterkante des iPhone ein und schiebe es die rechte Seite hoch, um den Kleber darunter aufzutrennen.

    • Schiebe das Plektrum nicht tiefer als 3 mm ein, du könntest sonst die Displaykabel beschädigen.

    If you have flat feeler gauges (for adjusting engine valve tappet clearance, ignition points … old school) the .003” thick gauge goes right in. Work your way up in thickness until you can get the pic or supplied pry tool in. Don’t insert metal feeler gauge in too far, just enough to hold crack open. I didn’t need to use the suction cup. I used a hot/cold gel pack heated in microwave to heat edges to soften glue a bit. Made sure it wasn’t so hot I couldn’t stand it on my skin.

    William Olstad - Antwort

  12. iPhone X Taptic Engine austauschen: Schritt 12, Bild 1 von 3 iPhone X Taptic Engine austauschen: Schritt 12, Bild 2 von 3 iPhone X Taptic Engine austauschen: Schritt 12, Bild 3 von 3
    • Die Oberkante des Displays ist mit Klebstoff und mit Klammern befestigt.

    • Schiebe das Plektrum um die obere Ecke des Displays herum und ziehe gleichzeitig vorsichtig das Display mit wackelnden Bewegungen herunter in Richtung des Lightninganschlusses.

    • Wenn du nicht vorsichtig bist, können die Klammern brechen. Sei geduldig und wende nicht zu viel Kraft an.

    • Setze auch hier das Plektrum nicht tiefer als 3 mm ein, sonst beschädigst du möglicherweise die Sensorgruppe des Front Panels.

    • Schiebe das Plektrum zur gegenüberliegenden Ecke und trenne die restlichen Klebeverbindungen, welche das Display noch befestigen.

    These are the best instructions I’ve ever read for anything.! Thank you!

    Peter Andrew - Antwort

  13. iPhone X Taptic Engine austauschen: Schritt 13, Bild 1 von 1
    • Ziehe an der kleinen Noppe am Saugheber, um ihn vom Display zu entfernen.

  14. iPhone X Taptic Engine austauschen: Schritt 14, Bild 1 von 3 iPhone X Taptic Engine austauschen: Schritt 14, Bild 2 von 3 iPhone X Taptic Engine austauschen: Schritt 14, Bild 3 von 3
    • Öffne das iPhone, indem du das Display von der linken Seite her hochklappst, wie die Seite eines Buches.

    • Versuche noch nicht, das Display ganz zu trennen, mehrere empfindliche Flachbandkabel verbinden es immer noch mit dem Logic Board des iPhones.

    • Achte darauf, dass der Rahmen wie gezeigt zusammen mit dem Display herauskommt und nicht im Gerät steckenbleibt.

    • Lehne das Display gegen einen Gegenstand, damit es abgestützt ist, wenn du daran arbeitest.

    • Lege das Display beim Zusammenbau richtig in Position, richte die Klammern an der Oberkante aus und drücke die Oberkante hinein, bevor du den Rest des Displays einrasten lässt. Wenn es nicht leicht einrastet, dann prüfe, ob die Klammern am Rand des Displays ringsum richtig sitzen und achte darauf, dass sie nicht verbogen sind.

    My phone came apart in a different way and looks not right the little box at the top of the display as actually bolted to the top of the frame body I think something went really wrong when I opened it.

    Mike Kostersitz - Antwort

    It opens like a book but be careful not to open it all the way — only as far as shown in the photo. Otherwise it will strain the thin cable that connects the sensor module and then no more FaceID for you (or, as it turns out me). This could have been made more explicit in the instructions.

    Richard Tucker - Antwort

    It opens like a book but be careful not to open it all the way  … the small stainless steel tabs that hold the screen around the metal frame, that are on the bend place (right side of the phone)… are tend to bend, you can straighten them back to 90 deg. but the plastic base that they are on? very fragile- watch out not to break the plastic bezel … it may come apart of the glass.

    dabur872 - Antwort

    Advice for re-assembly: Before closing up the phone with the seal, check if phone is powering up again and speaker, mic and sensors are still working. If done this check even before installing the board connector bracket in Step 13.

    Alexander Nowak - Antwort

  15. iPhone X Taptic Engine austauschen, Displayeinheit: Schritt 15, Bild 1 von 1
    In diesem Schritt verwendetes Werkzeug:
    Magnetic Project Mat
    $19.95
    Kaufen
    • Entferne fünf Y000 Schrauben, welche die Halterung des Verbinders des Logic Board befestigen:

    • Drei 1,1 mm Schrauben

    • Eine 3,1 mm Schraube

    • Eine 3,7 mm Schraube

    • Achte bei dieser Reparatur auf jede Schraube und stelle sicher, dass jede Schraube wieder genau an ihren alten Platz eingedreht wird. Vermeide damit, dass das Smartphone beschädigt wird.

    One thing I found helpful for replacing the screws was to use only the 000screwdriver tip, without the handle. This way, the tip isn’t magnetized and the screw doesn’t tend to ‘roll’ off the screwdriver tip (the screw has almost no mass, so the head (largest surface) is pulled around to the side of the screwdriver tip when magnetized).

    Rich May 23, 2020

    ungodly - Antwort

    My 3.1mm screw had a stripped head, could not remove it. (Factory defect, this iPhone was never opened)

    So I had to give up removing the display assembly, and jumped directly to battery replacement, Step 20.

    That was tricky as I had to keep the display at 90º with a risk of breaking display connectors, but hopefully the replacement went well.

    I would not recommend to do this but to follow the guide, but, in case someone encounters a similar issue, that could help!

    vingu - Antwort

    My 1.1mm screw had a stripped head. Used a 3mm steel drill to cut the head off (just 1 mm deep haha) so i could remove the bracket.

    Renout - Antwort

    Be careful on reassembly. Keep the screen supported and not moving. I had difficulty getting the screws in and ended up ruining the screen connectivity at the back of the screen where the ribbon cables go in near the center. I was trying to hand hold the screen and it ended up moving around too much.

    SETH GREEN - Antwort

    To keep track of the screws, I copy the photos showing their places, then arrange these photos on document in Pages, print it. Next I apply two sided sticky tape (the roll-on type). So all screws have their corresponding places …

    Max Glanzmann - Antwort

  16. iPhone X Taptic Engine austauschen: Schritt 16, Bild 1 von 1
    • Entferne die Halterung.

    • Die Halterung ist unter Umständen leicht angeklebt. Hebe sie vorsichtig, aber fest hoch, um sie zu lösen.

    • Beim Zusammenbau ist dies ein guter Zeitpunkt, um dein iPhone einzuschalten und alle Funktionen zu testen, bevor du das Display wieder festklebst. Denke dran, es danach wieder auszuschalten, bevor du weiter arbeitest.

    I tested it, then proceeded to close up the device without the bracket. Do I need to reopen and install? All connections are good?

    monastra7 - Antwort

    The bracket helps those many connectors underneath maintain good contact. Probably in the short term nothing bad will happen, but I’d hang onto the bracket and reinstall it when convenient.

    Jeff Suovanen -

    Agree with Jeff

    cgtyoder -

    I tested all imaginable functionality on the new OLED screen. Taptics are fine. Then, I noticed that the battery wasn't charging. Any ideas as to what could have gone wrong?

    Monica - Antwort

    for me, the replacement battery was completely dead, small panic when the power-on button was pressed, but quickly realised that this was the situation, and now watching the phone take a power cycle.

    James Stanbridge - Antwort

    Before clicking the screen assembly back, I tried to test the iPhone by pushing the start button, but nothing happened. After taking off the bracket, reseating the plugs I tried again - nothing happened! Then I plugged in the charging cable connected with the iMac, and it started immediately. So if the phone does not start using the startup button, it might just be a glitch when reconnecting the battery.

    Max Glanzmann - Antwort

  17. iPhone X Taptic Engine austauschen: Schritt 17, Bild 1 von 2 iPhone X Taptic Engine austauschen: Schritt 17, Bild 2 von 2
    • Hebele den Akkustecker mit einem sauberen Fingernagel oder einem Spudger aus seinem Sockel auf dem Logic Board.

    • Achte dabei darauf, nicht die schwarze Silikondichtung zu beschädigen, welche an diesem und anderen Verbindern auf der Platine angebracht ist. Diese Dichtungen sorgen für einen Extraschutz gegen Wasser und Staub.

    • Biege den Stecker etwas weg vom Logic Board, damit er nicht versehentlich einen Kontakt zum Sockel herstellen kann. Dadurch würde das iPhone während der Reparatur mit Strom versorgt werden.

    cosa può succedere se non si disconnette la scheda logica'?

    luca.valli - Antwort

    note: be careful not to crush or puncture your battery at this step!! I gave mine a minor dent, which I hope wont be a problem.. but something to keep in mind for fxlks in the future!

    Noal Balint - Antwort

    Thanks, already did it)

    Stephen Hedrick -

  18. iPhone X Taptic Engine austauschen: Schritt 18, Bild 1 von 2 iPhone X Taptic Engine austauschen: Schritt 18, Bild 2 von 2
    • Löse den Verbinder der Sensoreinheit des Frontpanels mit der Spudgerspitze oder dem Fingernagel.

  19. iPhone X Taptic Engine austauschen: Schritt 19, Bild 1 von 2 iPhone X Taptic Engine austauschen: Schritt 19, Bild 2 von 2
    • Löse den Verbinder des Kabels zum OLED Panel mit der Spudgerspitze oder dem Fingernagel.

    • Um Press - Fit - Verbinder wie diesen wieder anzuschließen, musst du ihn erst vorsichtig ausrichten und an einer Seite herunter drücken, bis er einklinkt, wiederhole das dann auf der anderen Seite. Drücke nicht in der Mitte.Wenn der Verbinder schlecht eingesetzt ist, können sich die Kontaktstifte verbiegen und irreparabel beschädigt werden.

    Snap ‘em in like little Legos.

    Ray Johnson - Antwort

    Maybe the manual should flip step 17 and 18 (as the digitizer cable from 18, is in the way of the OLED cable of step 17) ?

    Renout - Antwort

  20. iPhone X Taptic Engine austauschen: Schritt 20, Bild 1 von 2 iPhone X Taptic Engine austauschen: Schritt 20, Bild 2 von 2
    • Hebele den Verbinder des Touchscreen Kabels mit der Spudgerspitze aus seinem Sockel.

    • Der Verbinder sitzt etwas vertieft, das macht es schwierig, ihn wieder festzustecken. Lasse dir Zeit und richte ihn sorgfältig aus, und drücke ihn dann vorsichtig mit der Fingerspitze fest - erst auf einer Seite, dann auf der anderen. Du solltest es spüren, wenn er einrastet.

    • Wenn der Touchscreen an irgendeiner Stelle nach der Reparatur nicht reagiert, musst du den Akku trennen und diesen Verbinder wieder neu einsetzen. Achte dabei darauf, dass er richtig einklinkt und dass kein Staub oder etwas anderes im Sockel befindet.

    This was probably the hardest part other than trying to get the screen off with the crappy suction cups. I re-installed the bracket only the find out that the touch screen would not respond to touch. Had to remove the five screws, remove the bracket and reseat the recessed screen connector. Reseating the bracket took another 10+ minutes. I carefully used the angled forceps to grab the cable and align the connector being careful not to damage the cable.

    Once you have the connector seated, I would reconnect the battery, power on the phone, and check the touch screen response before re-installing the bracket (step 13).

    Tawan Khamapirad - Antwort

    Yeah, this was probably the trickiest part of the reassembly. The power connector cable kept getting in the way so I moved it carefully but fully out of the way. Then it was a matter of fiddling around with it a bit and being careful not to force it on.

    Jeffrey Hoy -

    I was positive that I had messed something up, I had powered up the phone to test three different times and everything seemed find except there was no touch at all. On my fourth attempt, I carefully examined everything for dust and debris (blowing gently), and I did notice that a corner of the connector (more like part of the ribbon) was bent slightly, and I straightened it. I don't know if it was the ribbon or some tiny debris, but after reseating a fourth time, it worked.

    Pol Llovet - Antwort

    Very important part of the tutorial. Be careful and patience! In my case the screen and camera didn't respond after assemble, so I tried again to reconnect the connector like tutorial said and it worked well. Now my iPhone feel like a new one 💪🏼

    Efrain Maestre - Antwort

  21. iPhone X Taptic Engine austauschen: Schritt 21, Bild 1 von 3 iPhone X Taptic Engine austauschen: Schritt 21, Bild 2 von 3 iPhone X Taptic Engine austauschen: Schritt 21, Bild 3 von 3
    • Das Flachbandkabel der Sensoreinheit am Frontpanel ist leicht festgeklebt.

    • Hebe das Kabel vorsichtig an, bis es sich ablöst.

    Do this sensor affect face id?

    bonglkv - Antwort

    It is part of the face id part so yes. This is the ear piece too so if the ribbon tears there is a chance the ear piece will stop working as well.

    Stephen Patterson - Antwort

    Be super careful handling this ribbon particularly. I did a battery install and, when I was done, I had a phone with a new battery and no Face ID. That’s a $300 Apple repair, and no 3rd party shop will touch it. I believe the ribbon lays vertically (i.e., perpendicular to the “floor” of the phone, against the side edge of the battery. During the re-install, I must have forced the ribbon into position after seating the connector, causing fatal flexing of the ribbon. (Don’t know this for sure, but I see another comment saying that this cable is part of Face ID.) Anyway, bottom line: BE CAREFUL REMOVING AND REINSTALLING THIS RIBBON!

    Jonathan Pines - Antwort

    My flex cable was more than lightly adhered in place. I needed to use a guitar pic or similar to help encourage adhesive to separate. I wouldn’t pull too hard like shown in pictures unless you had just the right grip on the ribbon cable so as to avoid damaging flex cable. See note above (5/31/20)

    William Olstad - Antwort

    Bizarre — it turns out my whole front panel sensor assembly came entire off of the front screen and is stuck to the logic board.

    Karl Jarvis - Antwort

    I also found the glue quite recluctant to release so I applied a second or two of heat using the wife's hair dryer which softened it and the cable lifted much easier then. Be careful not to apply too much heat though which could then impact other internal components.

    LosBenitos - Antwort

    Cho ít cồn 90° vào để mềm keo dễ tháo

    huuhaukimngan - Antwort

    my iphone x doesn't have a front panel sensor? in fact, it looks completely different than the picture???

    Kenneth McLeod - Antwort

    @kennethmcleod, most likely you've separated the screen frame from the screen itself. We see this most commonly when people neglect to remove the pentalobe screws next to the charging port. Usually the cure is to take out those screws, then repeat the screen removal process on the frame that's still attached to the phone.

    Jerry Wheeler -

    You don't need to disconnect the front sensor to change the screen. Just leave it connected and remove from the screen side.

    Anthony Boshell - Antwort

  22. iPhone X Taptic Engine austauschen: Schritt 22, Bild 1 von 1

    I tried this and broke the cable can it still repair

    Alexis Rodriguez - Antwort

    At this point I would have found it easier to remove the glue from the edges than later on when I was reassembling it. I bought the kit that had the replacement glue in it.

    Grant - Antwort

    Excellent guide! Would love to have a link to moving the sensor assembly from the old display to the new here.

    Nicole - Antwort

    CAUTION:

    Removing the Taptic Engine or Speaker in next step is optional and the guide continues as this was per se needed.

    Unnecessary work and also If you remove the speaker you lose the adhesive gasket and this is not included in the scope of delivery of the "Battery replacement" offering.

    So do not remove and avoid losing waterproofing.

    Julian Gonzalez - Antwort

  23. iPhone X Taptic Engine austauschen, Unterer Lautsprecher: Schritt 23, Bild 1 von 2 iPhone X Taptic Engine austauschen, Unterer Lautsprecher: Schritt 23, Bild 2 von 2
    • Achte darauf, dass du die drei Reihen Erdungspads unten am iPhone nicht berührst.

    • Entferne die sieben Schrauben, die die Halterung unterhalb der Taptic Engine und dem Lautsprecher befestigen:

    • Zwei 1,9 mm Y000 Schrauben

    • Eine 1,2 mm Y000 Schraube

    • Eine 1,6 mm Y000 Schraube

    • Eine 2,4 mm Kreuzschlitzschraube

    • Eine 1,7 mm Kreuzschlitzschraube

    • Eine 1,5 mm Kreuzschlitzschraube

    For battery replacement:

    It is not necessary to remove Taptic Engine and speaker to replace a battery. Go straight to the step #33

    Additional video: https://youtu.be/2GfBOlJEW10

    Alexander - Antwort

    I wish I seen this before I did all that! Thank you for that information. Next time I do something like this. I'm gonna pay more attention to the comments.

    Eric Marino -

    Removing the Taptic Engine and speaker greatly improves your chances of getting the battery adhesive strips out intact. If those break, you’ll have a much tougher time.

    Jeff Suovanen -

    Boy, I tried to skip removing these items but was unable to get the glue strips out with them in place, not much to grab and tabs were kind of stuck to a seam in the battery, and hard to tell the difference between the seam and the strip tabs. For me I had to remove these items to get this done.

    marshallburchard -

    I stopped removing things after getting the display side off. There were 3 screws stripped on the speaker cover which wouldn't come out so I punted. Just pried the battery out with a smudger tool and some patience, starting at the top and working towards the bottom. New battery is in and working fine.

    Andy Price - Antwort

    The 2.4mm screw identified as “green” needs a Y000 screwdriver

    seb6po - Antwort

    Thanks for not removing the following steps. this made me break the connector for the bottom speakers >:(

    Andrew Romano - Antwort

    The color codes are missing from my display — only on this step.

    nat2 - Antwort

    The screws color and quantities in list don’t match the schematic ! I wish i had a magnetic screw mat before starting, because not only i removed the Taptic Engine and speaker unnecessarily, but i also lost a screw ?

    fb.mailing.lists - Antwort

    For first timer, dont think its possible to skip these steps and remove battery. It’s hard to remove the glue

    Wex - Antwort

    Does anyone know the purpose of this bracket "with grounding pads"? What would be the possible side effects if it was damaged or not connected properly during reassembly?

    Anne Aunyme - Antwort

    I had to remove the tactic and speaker could not get the glue strips out so glad the steps to do so were in this guide.

    P Bond - Antwort

    Sure would like to know WHY the warning "Be careful not to touch the three rows of grounding pads..." What would or could happen if I did touch them??

    Chad Gagnon - Antwort

    Removing the battery strips is a major PITA, just skip this step and everything onwards, remove the one strip on the top part of the battery (according to step 33) and for the bottom part of the battery, pry it off with a plastic spudger.

    Yes, this is not the elegant solution, but the quickest and easiest one. This method is better, as you don't want to keep the old battery anyway, so why bother. (You must not puncture the battery though! But as long as you're only working with a plastic tool and are careful, nothing can happen from my experience.)

    speaker gasket - Antwort

  24. iPhone X Taptic Engine austauschen: Schritt 24, Bild 1 von 2 iPhone X Taptic Engine austauschen: Schritt 24, Bild 2 von 2
    • Hebe nun die Halterung von der Ecke, welche der Batterie am nächsten ist an. Versuche nicht, sie vollständig zu entfernen, da sie weiterhin mit einem kleinen Flex-Kabel verbunden ist.

  25. iPhone X Taptic Engine austauschen: Schritt 25, Bild 1 von 2 iPhone X Taptic Engine austauschen: Schritt 25, Bild 2 von 2
    • Halte die Halterung so, dass sie dich nicht stört, und benutze die Spudgerspitze, um das darunterliegende Flex-Kabel mit einer Hebelbewegung zu lösen.

  26. iPhone X Taptic Engine austauschen: Schritt 26, Bild 1 von 1
    • Entferne die Halterung.

    My bracket was in two pieces.

    Jim Steward - Antwort

  27. iPhone X Taptic Engine austauschen: Schritt 27, Bild 1 von 2 iPhone X Taptic Engine austauschen: Schritt 27, Bild 2 von 2
    • Entferne die 2,1 mm Y000-Schraube, welche die Abdeckung des Lautsprecherverbinders befestigt.

    L'unique vis non?

    Easy Repair - Antwort

    Effectivement ;-) Merci pour les bons yeux et la remarque !

    Claire Miesch -

  28. iPhone X Taptic Engine austauschen: Schritt 28, Bild 1 von 1
    • Entferne die Abdeckung des Lautsprecherverbinders.

  29. iPhone X Taptic Engine austauschen: Schritt 29, Bild 1 von 2 iPhone X Taptic Engine austauschen: Schritt 29, Bild 2 von 2
    • Benutze die Spudgerspitze, um den Lautsprecherverbinder hochzuheben und zu trennen.

    As mentioned in a comment by timblake2112 (see step 29), this step is not necessary and can be skipped skipped. I would advise you to do so, as removing your speaker is guaranteed to ruin your gasket and rubber seal. This will result in loss of water resistancy of your iPhone and could potentially harm the sound quality of your speaker.

    Try removing the Taptic Engine without removing the speaker. It might still be possible removing the battery adhesive strips and your speaker will stay in its original condition.

    speaker gasket - Antwort

  30. iPhone X Taptic Engine austauschen: Schritt 30, Bild 1 von 2 iPhone X Taptic Engine austauschen: Schritt 30, Bild 2 von 2
    • Passe beim Hochhebeln des Lautsprechers auf, dass du nicht das gerade gelöste Flexkabel beschädigst. Drücke es, wenn nötig, zur einer Seite hin, so dass der Lautsprecher beim Herauskommen Platz hat.

    • Setze einen Spudger unter die Oberkante des Lautsprechers in der Nähe vom Rand des iPhone Gehäuses.

    • Hebele vorsichtig nach oben und hebe die Oberkante des Lautsprechers an.

    • Prüfe beim Einbau des Lautsprechers die Position des Flexkabels und achte darauf, dass es nicht unter dem Lautsprecher eingeklemmt wird.

  31. iPhone X Taptic Engine austauschen: Schritt 31, Bild 1 von 3 iPhone X Taptic Engine austauschen: Schritt 31, Bild 2 von 3 iPhone X Taptic Engine austauschen: Schritt 31, Bild 3 von 3
    • Greife den Lautsprecher an den Seitenkanten an und rücke ihn etwas hin und her. Dadurch löst sich die Klebeverbindung zur Unterkante des iPhones.

    • Ziehe den Lautsprecher von der Unterkante des iPhones weg, bis sich die Klebedichtung löst.

    As mentioned in a comment by timblake2112 (see step 29), this step is not necessary and can be skipped skipped. I would advise you to do so, as removing your speaker is guaranteed to ruin your gasket and rubber seal. This will result in loss of water resistancy of your iPhone and could potentially harm the sound quality of your speaker.

    Try removing the Taptic Engine without removing the speaker. It might still be possible removing the battery adhesive strips and your speaker will stay in its original condition.

    speaker gasket - Antwort

  32. iPhone X Taptic Engine austauschen: Schritt 32, Bild 1 von 2 iPhone X Taptic Engine austauschen: Schritt 32, Bild 2 von 2
    • Entferne den Lautsprecher.

    • Die Klebedichtung des Lautsprechers lässt sich nicht mehr verwenden. Ziehe alle Reste davon mit einer Pinzette ab.

    • Damit das iPhone weiterhin gegen Staub und Feuchtigkeit geschützt ist, musst du beim Zusammenbau die Klebedichtung erneuern. Reinige die Klebefläche mit Isopropylalkohol und einem fussellfreien Tuch oder Filterpapier, damit die Dichtung gut klebt. Klebe die Dichtung zuerst am Lautsprecher an und baue ihn dann ein.

    You don’t need to remove the speaker and ruin its gasket. You can wiggle and slide the taptic engine out without removing the speaker. I’ve done this twice on rear shell replacement jobs.

    timblake2112 - Antwort

    Maybe I'm a bit daft, but where's the instruction just how to line up the speaker gasket when replacing? I only have one so I'd like to avoid wrecking it. And I completely cleaned off the old one in order to do a good job of things. Why no simple instruction from part supply link?

    MrRoundel - Antwort

  33. iPhone X Taptic Engine austauschen, Taptic Engine: Schritt 33, Bild 1 von 2 iPhone X Taptic Engine austauschen, Taptic Engine: Schritt 33, Bild 2 von 2
    • Entferne die 2,3 mm Kreuzschlitzschraube, welche die Taptic Engine festhält.

  34. iPhone X Taptic Engine austauschen: Schritt 34, Bild 1 von 2 iPhone X Taptic Engine austauschen: Schritt 34, Bild 2 von 2
    • Löse das Flexkabel der Taptic Engine, indem du es mit dem Spudger gerade aus seinem Sockel hochhebelst.

  35. iPhone X Taptic Engine austauschen: Schritt 35, Bild 1 von 1
    • Entferne die Taptic Engine.

Abschluss

Vergleiche dein neues Ersatzteil genau mit dem Originalteil. Möglicherweise musst du fehlende Bauteile übertragen oder Schutzfolien abziehen, bevor du es einbauen kannst.

Um dein Gerät wieder zusammenzusetzen, folge den Schritten in umgekehrter Reihenfolge.

Entsorge deinen Elektroabfall sachgerecht.

Die Reparatur verlief nicht wie geplant? In unserem Antwortenforum findest du Hilfe bei der Fehlersuche.

34 weitere Nutzer:innen haben diese Anleitung absolviert.

Besonderer Dank geht an diese Übersetzer:innen:

en de

100%

Diese Übersetzer:innen helfen uns, die Welt zu reparieren! Wie kann ich mithelfen?
Hier starten ›

Jeff Suovanen

Mitglied seit: 08/06/13

427.129 Reputation

259 Anleitungen geschrieben

Team

iFixit Mitglied von iFixit

Staff

136 Mitglieder

16.573 Anleitungen geschrieben

Ein Kommentar

不需要寫碼?按步驟換完後仍然不行work,賣家說要寫碼?

tseng.mt - Antwort

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 5

Letzte 7 Tage: 69

Letzte 30 Tage: 230

Insgesamt: 39,205