Diese Version enthält möglicherweise inkorrekte Änderungen. Wechsle zur letzten geprüften Version.
Was du brauchst
-
-
Schiebe das iPod-Öffnungswerkzeug aus Kunststoff an der Kante zwischen die weiße Kunststoffvorderseite und die Metallrückseite des iPods. Führe ihn einmal um den iPod herum, sodass alle fünf Häkchen, die den iPod zusammen halten, gelöst sind.
-
-
-
Führe das Öffnungswerkzeug weiter an der Seite des iPods entlang, um alle fünf Häkchen zu lösen.
-
-
-
Arbeite um dich langsam um die Ecke des iPods und löse die zwei Häkchen nahe am Dock-Verbinder.
-
-
-
Löse die fünf Häkchen, die den iPod zusammenhalten. Möglicherweise kannst du durch leichtes Wackeln an der Vorderseite die restlichen Häkchen lösen.
-
-
-
Hebe nun die Rückseite vom iPod ab, aber pass auf, dass du nicht am Kopfhöreranschluss hängen bleibst.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Peel up the metallic tape attached to the top of the battery.
-
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Lift the battery up from the hard drive and lay it next the the iPod (it is still connected to the logic board).
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Carefully disconnect the orange ribbon cable from the hard drive.
-
If the cable doesn't come free easily, it may be helpful to gently wiggle the cable from side to side.
-
Lift the hard drive out of the iPod.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Loosen the connector by pulling the brown locking bar toward the hard drive cable using the tips of your fingers.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Slide the hard drive cable out of its connector.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Lift the blue hard drive mounting bracket out of the iPod.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Carefully disconnect the white battery connector from the logic board. Be sure to pull only on the connector itself and not on the cables.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Loosen the touch wheel connector by pulling the brown locking bar toward the side of the iPod using the tips of your fingers.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Remove the 8 T6 Torx screws from the logic board.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Lift the logic board up enough to disconnect the orange touch wheel cable.
-
Lift the logic board out of the iPod.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Note the location of the four white plastic tabs securing the display to the logic board. These tabs must be released before the display can be removed.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Use a spudger or your finger to free the four white plastic tabs indicated in the previous picture.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Use a spudger to carefully disconnect the display ribbon cable from beneath the scroll wheel.
-
Lift the display off the logic board.
-
Rückgängig: Ich habe diese Anleitung nicht absolviert.
Ein:e weitere:r Nutzer:in hat diese Anleitung absolviert.