Einleitung
Hält die Batterie nicht mehr so lange? Tausche sie aus (Löten erforderlich)
Was du brauchst
-
-
Füge das große iPod Opening Tool in die Ritze zwischen der Vorder- und Rückseite unter den Dock-Connector ein. Fahre das Werkzeug vor und zurück, um eine Öffnung zu erzeugen. Die Kante des Werkzeugs sollte in die Richtung der Rückseite zeigen, um die Aluminium Vorderseite nicht versehentlich zu verkratzen.
-
-
-
Schiebe ein kleines iPod Opening Tool in die Ritze auf der Seite des Hold-Schalters mit der Kante in Richtung Rückseite zeigend.
-
-
-
Vergrößere den Spalt vorsichtig durch Drücken und Wackeln des kleinen iPod Opening Tools in dem Spalt in der Nähe jeder der Laschen, die auf der Rückseite befestigt sind, um die Klammern zur Mitte des iPods hin zu drücken bis beide Seiten frei sind.
-
-
-
Wiederhole denselben Vorgang wie im vorigen Schritt, um die fünf Klammern an der Seite der Kopfhörerbuchse zu lösen.
-
-
-
Nachdem die Klammern befreit sind, löse die zwei Hälften des iPods.
-
Die Rückseite ist nun losgelöst vom iPod.
-
-
-
Entferne die folgenden 3 Schrauben
-
Zwei 3mm Kreuzschlitzschrauben neben dem Dock-Connector.
-
Eine 4 mm Kreuzschlitzschraube entlang der Kante des Logic Boards.
Note that the 4mm screw has slightly wider pitch; you'll need this when putting the unit back together.
-
-
-
Löse die Erdungs-Lasche, die den Akku mit dem Logic Board verbindet.
-
-
-
-
Stecke das flache Ende eines Spudgers zwischen den Akku und die Seite mit der Kopfhörerbuchse auf der Vorderseite und hebele den Akku vom Kleber mit dem er im GehPause befestigt ist.
-
Drehe den Akku aus dem iPod heraus und lege ihn neben dem iPod. Der Akku ist noch mit drei Drähten an das Logic Board gelötet, entferne ihn daher noch nicht ganz.
-
-
-
Hebe das Logic Board vorsichtig am Dock-Connector Ende hoch, um sicher zu gehen, dass das Logic Board frei ist.
-
-
-
Greife das Ende des Logic Boards neben dem Akkuanschluss mit einer Hand und halte den Rest des iPods mit der anderen Hand.
-
Schiebe das Logic Board aus den Halteklammern auf der Rückseite des Displays heraus .
During the disassembly of the board I somehow "delaminated" the display. The result was that the display (after the battery was changed and the device closed again) looked "cloudy". From some angle you couldn't see anything at all anymore. The solution was to heat up the hole device with a hair dryer and rest it on it's front side for about an hour. After that it looked absolutely perfect again. I am not sure whether the heating is really necessary (maybe just lying the ipod on the front side over night would have the same effect) and surely one should be careful to not overheat the device.
-
-
-
Verwende einen Spudger, um die schwarze Plastikklappe des orangenen Displaykabels nach oben zu klappen. Die schwarze Klappe wird 90 Grad nach oben klappen und das Kabel freigeben.
Both ribbon cables were especially difficult to put back in. I can't say I succeeded in getting the nano to work again. If you can avoid detaching the cables, do it. If you're replacing the clickwheel, there's no way of avoiding it unfortunately.
A little tip if you are replacing the screen: Reconnect this ribbon cable from the new screen BEFORE affixing the screen to the adhesive! It will make it much easier. Also be sure that the little black things are UP before trying to put the ribbon in, and make sure you put them DOWN before closing up! The black things on the receptacle "lock" the cable in place, so it is important that you have it STRAIGHT or it wont work. Good luck!
-
-
-
Verwende einen Spudger, um das Display Flachbandkabel aus dem Stecker zu schieben.
Getting the display ribbon back in place is the most difficult maneuver in the whole fix. I actually broke the black plastic tab in half while trying to close it back down, (be very gentle with it!). Managed to put the broken half back in(tweezers and patience) and get that ribbon in and put it back down. This battery replacement was the most difficult/tedious repair I have ever done. Don't do it unless you are brave and stubborn.
You can leave out this steps with disconnecting the two cables.
Without disconnecting the two cables, one can separate the two pieces only 1/2 inch. This is enough to work carefully with the soldering iron and change the battery.
It's a little bit difficult to work with the needle to open the three holes after removing the old battery - but you can do it.
From the reading of the other notes it seems to me easier than to disconnect the two cables
-
-
-
Verwende einen Spudger, um die schwarze Klappe des orangenen Click-Wheel Flachbandkabels nach oben zu klappen. Sie wird im 90 Grad Winkel nach oben klappen, und das Kabel freigeben.
-
-
-
Verwende einen Spudger um das Click-Wheel Flachbandkabel aus dem Stecker zu schieben.
Don't do this unless you have to. Getting this ribbon back in is nearly impossible.
Zitat von daisystanton:
Don't do this unless you have to. Getting this ribbon back in is nearly impossible.
Try using tweezers or medical clamps to reach in that tight spot. Use these tools to also connect the click wheel ribbon back to the logic board.
Stamp tweezers worked great for the ribbon cable! (Search eBay or Amazon, or your local hobby store.) This would be a useful tool for iFixIt to add to their inventory.
-
-
-
Beginne damit, den ungeschützen Teil des weißen Akkukabels mit der Spitze des Lötkolbens zu erhitzen und gleichzeitig das Kabel mit der Pinzette am der isoliertem Teil vom Verbinder wegzuziehen.
-
Entlöte die restlichen Kabel mit der oben beschriebenen Methode.
-
-
-
Wenn vorhanden, löse das kleine Stück Schrumpfschlauch, der das positive Akkukabel schützt.
-
-
-
Um die Lötstellen zu öffnen, öffne eine Sicherheitsnadel und drücke sie gegen den Lötzinn, der das Loch blockiert. Zur gleichen Zeit, erhitze die gleiche Stelle von der anderen Seite des Logic Boards. Um die Löcher komplett frei zu bekommen, muss diese Technik mehrfach von beiden Seiten des Boards angewandt werden.
A desoldering pump is helpful and makes this step much easier. You basically heat the solder up til it goes liquid, then hit the button on the desoldering pump and all the solder is taken off leaving the hole totally clean.
-
-
-
Plaziere das Logic Board flach auf einen Tisch mit den goldenen Erdungs-Kontakten (in Orange gezeigt) nach oben.
-
Stecke die abgezogenen Kabel mit einer Pinzette in das jeweilige Loch
-
Stecke das schwarze Kabel in das Loch neben dem Hold-Schalter (in rot markiert)
-
Stecke das rote Kabel in das mittlere Loch.
-
Stecke das weiße kabel in das Loch, das am weitesten von dem Hold-Schalter entfernt ist.
-
-
-
Drehe das Logic Board und den Akku um, sodass die blanken Enden der Akkukabel nach oben zeigen.
-
-
-
Löte die Verbindung, indem die Spitze kurzzeitig an die Verbindung gehalten wird, der Lötzinn in die Verbindung schmilzt und entferne die Spitze und den Lötzinn schnell wieder. Der Lötzinn sollte um das neue Akkukabel herumfließen und es fest an das Lötfeld des Logic-Boards befestigen.
-
Löte die zwei andern Akkukabel auf die gleichen Art und Weise und achte dabei darauf, dass sich die Verbindungen gegenseitig nicht berühren.
-
-
-
Drehe den Akku zum Logic-Board und platziere ihn flach in seine Stelle und biege die Kabel falls nötig.
-
Um das Gerät wieder zusammenzubauen, folge diese Anleitung in umgekehrter Reihenfolge
Um das Gerät wieder zusammenzubauen, folge diese Anleitung in umgekehrter Reihenfolge
Rückgängig: Ich habe diese Anleitung nicht absolviert.
104 weitere Nutzer:innen haben diese Anleitung absolviert.
Besonderer Dank geht an diese Übersetzer:innen:
100%
Diese Übersetzer:innen helfen uns, die Welt zu reparieren! Wie kann ich mithelfen?
Hier starten ›
12 Kommentare
I skipped steps 8,9,11-17, and 21.
Step 19> when un-soldering the old battery wires, make sure to leave solder on the pads and in the holes.
I replaced steps 22-24 with Step 22-24> Very carefully and precisely:
-Place the black lead onto the pad nearest the hold switch (shown in red) with the end of wire pointing away from the battery.
-Place the red lead onto the center pad with the end of wire pointing away from the battery.
-Place the white lead onto the pad furthest from the hold switch with the end of wire pointing away from the battery.
Gently hold each wire in place on the pad while applying the soldering iron taking care not to touch the wire to any other pad or trace (note black wire). When the wire sinks into the solder, remove heat. Hold wire until solder has set.
Do step 25 and charge battery. Much simpler and less risk.
For all newbies, make sure that your soldering spots are neat and clean. Your workplace must be clean! Too hasty repair...and you'll reassemble your Pod once again.
Thanks for the neat repair guide! Much appreciated!" Now I can enjoy my "new Pod" for another 8years at least! No that's what I call environmental awareness! (built in 2005)
Well, how’s it going? It’s been 8 years…
Success! The instructions were clear and helpful. This was the third battery for my iPod, so the desoldering step took a fair amount of time. I am not very experienced with soldering, so I practiced on a little blinking christmas tree kit before attempting this, and I think that was useful.
MUCH easier than I expected. For me the hardest part was getting the rear cover back on. LOL!
First the iPod worked before I put the rear cover back on…then nothing works…the iPod ist dead. I think there must be a short circuit.
What can I do to rescue it?!
Why not cut the 3 wires and splice vs. soldering to PWA? Much less risk to board and easier to do.
I successfully replaced the battery on my iPod nano, the first iPod I’ve ever bought. The hardest part for me was to open the solder holes for the wires, I used a blood lancet for this, but it took a lot of time. While the three wires are glued together on the original battery, they are loose on the replacement battery, which required guiding them in the right position (and staying there) to prevent them from overlapping. After reconnecting the display (using tweezers), it only showed a white screen, but after resetting by pressing menu and middle button for 5 secs, the iPod was working again – and as nice side effect: the clicker is working again too.
For anyone else looking at this, use solder braid to get the holes open. It's the best way to do it in nearly every circumstance.
Öffnen und Ausbau der Hauptplatine ging mit geeignetem Werkzeug sher schnell. Eine Entlötpumpe würde ich nicht empfehlen. Besser geht es mit Entlötlitze und reichlich Flußmittel (z. B. No-Clean X32-10i Flux).
Am schwierigsten gestaltet sich das Wiedereinführen der Flachbandverbindungen. Ansonsten eine Superanleitung, danke.
Turn on the notes and READ thru all the steps and the notes, especially the ones involving the ribbon cables.
patjmccarthy - Antwort