Einleitung
Dies ist nur eine grundständige Anleitung, um den Akku vom Rückgehäuse abzulösen.
Was du brauchst
-
-
Entferne die drei 1,6 mm Kreuzschlitzschrauben #000, mit denen das Logic Board am Rückgehäuse befestigt ist.
-
-
-
Der Akku ist mit zwei Klebestreifen befestigt.
-
Drehe den iPod um und erhitze die RÜCKSEITE des iPod Aluminiumgehäuses mit einem Fön oder einem Heißluftgebläse. Erhitze nicht den Akku.
-
Das Aluminium-Gehäuse muss nicht heiß werden, du solltest alle erwärmten Teile immer problemlos anfassen können.
Instead of a heat gun or hair dryer, I used a rice sock (http://www.wikihow.com/Make-a-Rice-Sock) to apply heat evenly across the entire back of the case while the case still sat upright for me to work on getting the battery loose. It was a lot easier than trying to heat the back of the case, then flip the case over and work feverishly before it cooled.
I'm sure this works, but it doesn't seem like the proper way to do this. I didn't like the feeling of prying on a flimsy battery at all. That's not practical. Instead get some molybdenum wire start it underneath the corners, then wrap the ends of the wire on like 2 pencils then tape them so u dont have to wrap the wire around your fingers because it will hurt lol. then apply heat, i went about 130 degrees is what my infrared gun said. I used a geat gun on low and a good distance away. Then just work the wire down the adhesive obviously lol. This worked out very easily for me and I felt safe and more confident about what I was doing. Good luck.
If you really don’t want to remove the battery, you may lift the mainboard slightly instead and disonnect display, back camera flexes and antenna connector. Then gently pull back camera module out of the seat. This gives you enough room to connect new display and back camera flexes. Back cam module would be hanging while you connect everything that got disconnected. Screw back the mainboard and push camera module to its seat.
-
-
-
Setze ein Kunststoff-Öffnungswerkzeug in die oberer rechte Kerbe und heble vorsichtig am Akku.
-
-
-
-
Mache an der unteren rechten Kerbe weiter. Setze das Kunststoff-Öffnungswerkzeug in die Kerbe und heble vorsichtig an der Seite des Akkus.
-
-
-
Sobald der ganze Kleber abgelöst ist, kannst du den Akku von der Unterkante her zur linken Seite hin aus dem Rückgehäuse heraus drehen.
-
Klappe den Akku um, damit sein Kabel flach liegt, und lege ihn ab.
-
Um dein Gerät wieder zusammenzubauen, folge den Schritten dieser Anleitung in umgekehrter Reihenfolge.
Um dein Gerät wieder zusammenzubauen, folge den Schritten dieser Anleitung in umgekehrter Reihenfolge.
Rückgängig: Ich habe diese Anleitung nicht absolviert.
Ein:e weitere:r Nutzer:in hat diese Anleitung absolviert.
Besonderer Dank geht an diese Übersetzer:innen:
100%
Annika Faelker hilft uns, die Welt in Ordnung zu bringen! Wie kann ich mithelfen?
Hier starten ›
3 Kommentare
This isn't even half of the procedure - the battery isn't even completely removed, much less replaced! Helpful but nowhere near complete.
Yeah, you might have skipped the most critical steps, like glass and bezel removal, desoldering, soldering etc..
Hi, the MPN on that WiFi flex confirms this is not an iPod Touch 6th gen, it is 5th Gen. I am trying to source a 6th Gen WiFi Flex.
Ricky Pohlman - Antwort