Zum Hauptinhalt wechseln

Diese Version enthält möglicherweise inkorrekte Änderungen. Wechsle zur letzten geprüften Version.

Was du brauchst

  1. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 1, Bild 1 von 1
    • Rotate the Roomba so the bumper is in front of you.

  2. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 2, Bild 1 von 1
    • Remove the wheel using a spudger. You can probably also do this with your hand depending on how dirty the wheel is.

  3. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 3, Bild 1 von 1
    • Remove the wheel guiding inlay using the spudger or your hand.

  4. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 4, Bild 1 von 1
    • Remove the main brush by unscrewing the single 5 mm screw on the yellow side sweeper using the Phillips #1 driver.

    • Once the screw is removed, lift out the brush and store the screw and brush.

  5. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 5, Bild 1 von 3 : Schritt 5, Bild 2 von 3 : Schritt 5, Bild 3 von 3
    • Using the Phillips #1 driver, remove the four 10 mm screws that hold the back panel in place.

    • Once the four screws are removed, store the safely and lift up the back panel.

  6. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 6, Bild 1 von 2 : Schritt 6, Bild 2 von 2
    • Remove the vacuum try to have an easier repair.

  7. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 7, Bild 1 von 2 : Schritt 7, Bild 2 von 2
    • Locate the battery.

    • Lift up the yellow battery by pulling up the green tabs on its side.

    • Handle the battery with care.

  8. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 8, Bild 1 von 3 : Schritt 8, Bild 2 von 3 : Schritt 8, Bild 3 von 3
    • Using the Phillips #1 driver, remove the three screws that hold back the wheel unit on each side. This is not required but will make the repair easier.

    • Lift out the wheel units and store safely.

    • Repeat on the other side.

  9. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 9, Bild 1 von 2 : Schritt 9, Bild 2 von 2
    • Check that the unit now looks like this and all the parts are removed.

    • Flip the unit around.

  10. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 10, Bild 1 von 1
    • Use your hands to unhook the snaps between the silver panel from the black panel located where the vacuum bin was.

  11. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 11, Bild 1 von 3 : Schritt 11, Bild 2 von 3 : Schritt 11, Bild 3 von 3
    • Using the ifixit spudgers pry under the main silver panel.

  12. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 12, Bild 1 von 1
    • Lift off the panel.

  13. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 13, Bild 1 von 1
    • Turn the unit around again and locate the 10 screws on the front bumper.

    • Using the Phillips #1 driver, remove the ten 10 mm screws on the bumper that run along the outer edge of the Roomba.

  14. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 14, Bild 1 von 3 : Schritt 14, Bild 2 von 3 : Schritt 14, Bild 3 von 3
    • Lift the thin top cover that holds the bumper in place.

    • Be very vigilant with the attached sensor. Otherwise you risk ripping off the cable and damaging the entire sensor.

  15. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 15, Bild 1 von 2 : Schritt 15, Bild 2 von 2
    • Lift the bumper upwards for easier access.

    • Unscrew the two 5 mm screws that connect the red and white wires to the device using the Phillips #1 driver.

    • Lift the circular black panel off the sensor housing.

  16. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 16, Bild 1 von 1
    • Turn the unit back around.

  17. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 17, Bild 1 von 1
    • Using the Phillips #1 driver, unscrew the following 13 screws that hold the black panel in place:

    • Two 5 mm on the bottom ends of the semicircle handle.

    • Ten 7.5 mm scattered on the Roomba.

    • One 5 mm at the bottom of control board.

  18. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 18, Bild 1 von 1
    • Lift the black panel off the device.

  19. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 19, Bild 1 von 3 : Schritt 19, Bild 2 von 3 : Schritt 19, Bild 3 von 3
    • Remove the outer silver circle, black plastic cover, and black film from the central control board in that order.

  20. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 20, Bild 1 von 1
    • Using the Phillips #1 driver, unscrew the four 10 mm screws that surround the clean button.

  21. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 21, Bild 1 von 1
    • Lift off the panel.

  22. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 22, Bild 1 von 2 : Schritt 22, Bild 2 von 2
    • Lift off the plastic sheet.

  23. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 23, Bild 1 von 3 : Schritt 23, Bild 2 von 3 : Schritt 23, Bild 3 von 3
    • Remove all the top connectors to the mainboard.

    • You can use ifixit's reverse pliers but you can also use your hands.

  24. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 24, Bild 1 von 1
    • Using the Phillips #1 driver, unscrew the five screws on the mainboard.

    • Do not rip out mainboard now!

  25. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 25, Bild 1 von 3 : Schritt 25, Bild 2 von 3 : Schritt 25, Bild 3 von 3
    • Carefully lift off the mainboard, moving it towards you.

    • Be very careful with the connected connectors.

  26. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 26, Bild 1 von 1
    • Very carefully disconnect the connections off the mainboard.

    • You can ifixit's reverse pliers.

  27. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 27, Bild 1 von 2 : Schritt 27, Bild 2 von 2
    • The sensor might still be attached/is not attached to the main unit but mainboard. Just unplug it.

    • You can now replace the mainboard and complete the steps from the bottom up to finish the replacement.

Ziellinie

4 weitere Nutzer:innen haben diese Anleitung absolviert.

Max Lembke

Mitglied seit: 09/14/19

924 Reputation

3 Anleitungen geschrieben

Ein Kommentar

Greetings. I have two Model 560 sweepers. Neither of them has ever had a software update. I've tried resetting them to see if it will get them to complete a cleaning cycle, but they either short cycle back to the charger base, or crap out prematurely. I've installed a generic 5000 mAh battery, so there should be adequate power to complete two rooms with less than 50% carpet. Is there anybody out there who has one of the "Osmo" software updaters? I like the Model 560, and I have updated the gear drives and dust collectors, so I'd prefer NOT to junk them. Please advise.

Ed Allen, a.k.a. nostrodamos@live.com

Pasco, WA

(509) 542-1004

Ed Allen - Antwort

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 2

Letzte 7 Tage: 17

Letzte 30 Tage: 76

Insgesamt: 3,164