Zum Hauptinhalt wechseln

Repariere deine Sachen

Recht auf Reparatur

Werkzeug & Ersatzteile

Einleitung

This is when things start to get a little more tricky. Start to be more careful because everything you are dealing with is attached to your motherboard from here on out.

Ersatzteile

Keine Ersatzteile angegeben.

  1. Remove the dust bin by pushing on the button for the dust bin removal Pull the dust bin out
    • Remove the dust bin by pushing on the button for the dust bin removal

    • Pull the dust bin out

  2. Pull up on the silver handle to release the top protectant plastic Remove the top plastic carefully
    • Pull up on the silver handle to release the top protectant plastic

    • Remove the top plastic carefully

  3. Remove the ten 11mm screws that hold the front bumper to the plastic bumper protector with your Phillips #1 screwdriver. Pull the plastic bumper protector up and off of the bumper.
    • Remove the ten 11mm screws that hold the front bumper to the plastic bumper protector with your Phillips #1 screwdriver.

    • Pull the plastic bumper protector up and off of the bumper.

  4. Manta Precision Bit Set

    112 Bits für jede Reparatur.

    Upgrade Your Toolbox

    Manta Precision Bit Set

    Upgrade Your Toolbox
  5. Flip the Roomba back over, so you are viewing the top. Pull up on the front bumper to remove it. Be careful not to pull too hard because there is wiring attached to the bumper.
    • Flip the Roomba back over, so you are viewing the top.

    • Pull up on the front bumper to remove it.

    • Be careful not to pull too hard because there is wiring attached to the bumper.

    • Remove the two 7mm screws with your Phillips #1 screwdriver, holding the wire sensors in place to the front bumper.

  6. The outside six - 10mm screws and the inside set of four - 10mm screws are the same here, use your Phillips head #2 to remove them Use your Phillips head #0 to remove the one - 7mm bottom center screw Use your Phillips head #2 to remove the two - 8mm screws by the handle
    • The outside six - 10mm screws and the inside set of four - 10mm screws are the same here, use your Phillips head #2 to remove them

    • Use your Phillips head #0 to remove the one - 7mm bottom center screw

    • Use your Phillips head #2 to remove the two - 8mm screws by the handle

    • Push down the two release points to pull the plastic piece up

    • Pull the plastic piece up

  7. Pull the silver tab, and clear tinted display off Remove the 4 - 9mm  screws holding the display with your Phillips head #0 Remove the 4 - 9mm  screws holding the display with your Phillips head #0
    • Pull the silver tab, and clear tinted display off

    • Remove the 4 - 9mm screws holding the display with your Phillips head #0

  8. Remove the display Remove the plastic protectant film from the motherboard Remove the plastic protectant film from the motherboard
    • Remove the display

    • Remove the plastic protectant film from the motherboard

Abschluss

To reassemble your device, follow these instructions in reverse order.

Ein weiterer Nutzer hat diese Anleitung absolviert.

Rhett

Mitglied seit: 22.01.2015

1.121 Reputation

7 Anleitungen geschrieben

Team

Cal Poly, Team 21-20, Maness Winter 2015 Mitglied von Cal Poly, Team 21-20, Maness Winter 2015

CPSU-MANESS-W15S21G20

4 Mitglieder

14 Anleitungen geschrieben

Kommentar hinzufügen

Statistik anzeigen:

Letzten 24 Stunden: 0

Letzten 7 Tage: 1

Letzten 30 Tage: 5

Insgesamt: 533