Zum Hauptinhalt wechseln
Hilfe

Sony Xperia XA LCD Screen Replacement

How to replace the LCD screen on a Sony Xperia XA.

You will need to use a source of heat. You may need to buy adhesive for the reassembly. Make sure the phone is completely powered off before opening the device.

Abschnitte
Werkzeuge

Schritt 1 LCD Screen  ¶ 

Remove the four 4mm screws holding the loudspeaker in place with a Phillips #00 screwdriver. Remove the four 4mm screws holding the loudspeaker in place with a Phillips #00 screwdriver.

Schritt 1 LCD Screen  ¶ 

  • Remove the four 4mm screws holding the loudspeaker in place with a Phillips #00 screwdriver.

Schritt 2  ¶ 

Push back the two retaining tabs on the top of the loudspeaker with the spudger. Push back the two retaining tabs on the top of the loudspeaker with the spudger.

Schritt 2  ¶ 

  • Push back the two retaining tabs on the top of the loudspeaker with the spudger.

Schritt 3  ¶ 

Pry the loudspeaker up with the spudger.

Schritt 3  ¶ 

  • Pry the loudspeaker up with the spudger.

Schritt 4  ¶ 

Remove the loudspeaker with your hands.

Schritt 4  ¶ 

  • Remove the loudspeaker with your hands.

Schritt 5  ¶ 

With a spudger, pry up the orange connector that is directly underneath where the loud speaker was just removed.

Schritt 5  ¶ 

  • With a spudger, pry up the orange connector that is directly underneath where the loud speaker was just removed.

Schritt 6  ¶ 

Pry up the small silver connector on the right side of the bottom of the phone with a spudger. Pry up the small silver connector on the right side of the bottom of the phone with a spudger.

Schritt 6  ¶ 

  • Pry up the small silver connector on the right side of the bottom of the phone with a spudger.

Schritt 7  ¶ 

Pry up the charging port using a spudger. Pry up the charging port using a spudger.

Schritt 7  ¶ 

  • Pry up the charging port using a spudger.

Schritt 8  ¶ 

Remove the five black 4mm screws with a Phillips #00 screwdriver. Remove the five black 4mm screws with a Phillips #00 screwdriver.

Schritt 8  ¶ 

  • Remove the five black 4mm screws with a Phillips #00 screwdriver.

Schritt 9  ¶ 

Pry up the black camera case with a nylon spudger, and then remove the case.

Schritt 9  ¶ 

  • Pry up the black camera case with a nylon spudger, and then remove the case.

Schritt 10  ¶ 

Use a spudger to pry up the six motherboard connectors. Use a spudger to pry up the six motherboard connectors. Use a spudger to pry up the six motherboard connectors.

Schritt 10  ¶ 

  • Use a spudger to pry up the six motherboard connectors.

Schritt 11  ¶ 

Use the flat end of the nylon spudger to lift the camera out of the phone.

Schritt 11  ¶ 

  • Use the flat end of the nylon spudger to lift the camera out of the phone.

Schritt 12  ¶ 

Pull out the front camera using your fingers.

Schritt 12  ¶ 

  • Pull out the front camera using your fingers.

Schritt 13  ¶ 

Use the spudger to separate the motherboard from the frame.

Schritt 13  ¶ 

  • Use the spudger to separate the motherboard from the frame.

Schritt 14  ¶ 

Pry up the headphone jack using a spudger. Pry up the headphone jack using a spudger.

Schritt 14  ¶ 

  • Pry up the headphone jack using a spudger.

Schritt 15  ¶ 

Peel back the black tabs that were holding the battery in place. You may hear loud sounds as you pull the tabs because they are stuck with adhesive.

Schritt 15  ¶ 

  • Peel back the black tabs that were holding the battery in place.

  • You may hear loud sounds as you pull the tabs because they are stuck with adhesive.

Schritt 16  ¶ 

Remove the two 4 mm screws with a Phillips #000 screwdriver from the left side of the back of the screen. Remove the two 4 mm screws with a Phillips #000 screwdriver from the left side of the back of the screen.

Schritt 16  ¶ 

  • Remove the two 4 mm screws with a Phillips #000 screwdriver from the left side of the back of the screen.

Schritt 17  ¶ 

Remove the three 3mm screws with a T5 screwdriver along the side of the device where the volume buttons are. Remove the three 3mm screws with a T5 screwdriver along the side of the device where the volume buttons are.

Schritt 17  ¶ 

  • Remove the three 3mm screws with a T5 screwdriver along the side of the device where the volume buttons are.

Schritt 18  ¶ 

Push down the side of the screen that you just removed screws from. Push down the side of the screen that you just removed screws from.

Schritt 18  ¶ 

  • Push down the side of the screen that you just removed screws from.

Schritt 19  ¶ 

Pull up the orange and black tab that is on the left half of the middle of the screen. Pull up the orange and black tab that is on the left half of the middle of the screen. Pull up the orange and black tab that is on the left half of the middle of the screen.

Schritt 19  ¶ 

  • Pull up the orange and black tab that is on the left half of the middle of the screen.

Schritt 20  ¶ 

Remove the Wifi antenna. Remove the Wifi antenna.

Schritt 20  ¶ 

  • Remove the Wifi antenna.

Schritt 21  ¶ 

Remove the three 3 mm screws with a Star Bit T5 Screwdriver on the opposite side of the phone. Remove the three 3 mm screws with a Star Bit T5 Screwdriver on the opposite side of the phone.

Schritt 21  ¶ 

  • Remove the three 3 mm screws with a Star Bit T5 Screwdriver on the opposite side of the phone.

Schritt 22  ¶ 

Use tweezers to remove the earpiece. Use tweezers to remove the earpiece.

Schritt 22  ¶ 

  • Use tweezers to remove the earpiece.