Zum Hauptinhalt wechseln
Hilfe

Motorola Droid X Motorola Droid X Rear Housing Replacement

This guide explains how one can remove the rear housing of the Motorola Droid X.

  • Autor: Sam Johnston
  • Geschätzte Zeit: 15 Minuten
  • Schwierigkeitsgrad: Einfach

If one needs access to the inner components of the Droid X or they are needing to replace the rear plastic of the device, this guide will walk a reader through the necessary steps.

Schritt 1 Motorola Droid X Rear Housing  ¶ 

Remove the micro SD card from its connector.

Schritt 1 Motorola Droid X Rear Housing  ¶ 

  • Remove the micro SD card from its connector.

Schritt 2  ¶ 

Locate the seam between the back case and the end cover on the top edge of the phone. Use the plastic opening tool to detach the two clips by wedging the tool into the right side of the seam and moving right to left.  Once the cover comes off set it aside Use the plastic opening tool to detach the two clips by wedging the tool into the right side of the seam and moving right to left.  Once the cover comes off set it aside

Schritt 2  ¶ 

  • Locate the seam between the back case and the end cover on the top edge of the phone.

  • Use the plastic opening tool to detach the two clips by wedging the tool into the right side of the seam and moving right to left. Once the cover comes off set it aside

Schritt 3  ¶ 

Repeat step 2 on the bottom cover. Repeat step 2 on the bottom cover. Repeat step 2 on the bottom cover.

Schritt 3  ¶ 

  • Repeat step 2 on the bottom cover.

Schritt 4  ¶ 

Use a T5 Torx screwdriver to remove the screws in each corner of the phone. The screws are very small so make sure not to lose them. The screws are very small so make sure not to lose them.

Schritt 4  ¶ 

  • Use a T5 Torx screwdriver to remove the screws in each corner of the phone.

  • The screws are very small so make sure not to lose them.

Schritt 5  ¶ 

Flip the phone over and locate the screw on the middle of the left side. Unscrew it using the T5 Torx screwdriver and set it aside. Flip the phone over and locate the screw on the middle of the left side. Unscrew it using the T5 Torx screwdriver and set it aside.

Schritt 5  ¶ 

  • Flip the phone over and locate the screw on the middle of the left side. Unscrew it using the T5 Torx screwdriver and set it aside.

Schritt 6  ¶ 

Identify the screw located in the bottom right corner of the battery case.  Remove the screw with a T5 (or in some cases T6) torx screwdriver and set it aside. Identify the screw located in the bottom right corner of the battery case.  Remove the screw with a T5 (or in some cases T6) torx screwdriver and set it aside.

Schritt 6  ¶ 

  • Identify the screw located in the bottom right corner of the battery case. Remove the screw with a T5 (or in some cases T6) torx screwdriver and set it aside.

Schritt 7  ¶ 

Locate the seam along the right edge of the phone.  Use the prying tool to disconnect the two clips along the edge. Locate the seam along the right edge of the phone.  Use the prying tool to disconnect the two clips along the edge.

Schritt 7  ¶ 

  • Locate the seam along the right edge of the phone. Use the prying tool to disconnect the two clips along the edge.

Schritt 8  ¶ 

Locate the two clips on the inside of the case and use the spudger tool to detach them from the case.  To detach each clip, use the sharp end to press the small, black plastic in the center of the clip. Locate the two clips on the inside of the case and use the spudger tool to detach them from the case.  To detach each clip, use the sharp end to press the small, black plastic in the center of the clip. Locate the two clips on the inside of the case and use the spudger tool to detach them from the case.  To detach each clip, use the sharp end to press the small, black plastic in the center of the clip.

Schritt 8  ¶ 

  • Locate the two clips on the inside of the case and use the spudger tool to detach them from the case. To detach each clip, use the sharp end to press the small, black plastic in the center of the clip.

Schritt 9  ¶ 

After the clips are detached, remove the back case and set it aside. After the clips are detached, remove the back case and set it aside.

Schritt 9  ¶ 

  • After the clips are detached, remove the back case and set it aside.