Zum Hauptinhalt wechseln
Hilfe

Dyson DC14 Motor Replacement

This guide will show you how to replace the Dyson DC14 motor.

  • Autor: Miriam Krage
  • Geschätzte Zeit: 1 Stunde
  • Schwierigkeitsgrad: Schwierig

This guide will show you the necessary steps to replace the motor in your Dyson DC14 Vacuum. This is a lengthy process; you should set aside a good amount of time to finish this guide in one attempt.

Relevante Ersatzteile

Schritt 1 Motor  ¶ 

Place vacuum upright, with the canister facing you. Remove the canister, setting the canister aside.

Schritt 1 Motor  ¶ 

  • Place vacuum upright, with the canister facing you.

  • Remove the canister, setting the canister aside.

Schritt 2  ¶ 

Insert flathead screwdriver under each latch and pry up gently. Do not try to lift the latches up very far, they could snap off! Open the cover, remove the exhaust filter, and set the filter to the side

Schritt 2  ¶ 

  • Insert flathead screwdriver under each latch and pry up gently.

  • Do not try to lift the latches up very far, they could snap off!

  • Open the cover, remove the exhaust filter, and set the filter to the side

Schritt 3  ¶ 

Place vacuum face down. Remove the u-bend pipe that connects the canister to the telescopic wand.

Schritt 3  ¶ 

  • Place vacuum face down.

  • Remove the u-bend pipe that connects the canister to the telescopic wand.

Schritt 4  ¶ 

Pull the clear hose out of the gasket on the right side of the vacuum under the axle. Pull the hose straight back towards you.

Schritt 4  ¶ 

  • Pull the clear hose out of the gasket on the right side of the vacuum under the axle.

  • Pull the hose straight back towards you.

Schritt 5  ¶ 

Remove brush-bar housing by prying the housing out of the clips that hold it. Pull brush-bar housing toward you while keeping vacuum stationary.

Schritt 5  ¶ 

  • Remove brush-bar housing by prying the housing out of the clips that hold it.

  • Pull brush-bar housing toward you while keeping vacuum stationary.

Schritt 6  ¶ 

Remove the three T15 torx screws that secure the cover to the brush clutch belt.

Schritt 6  ¶ 

  • Remove the three T15 torx screws that secure the cover to the brush clutch belt.

Schritt 7  ¶ 

Pull the cover of the brush clutch belt out towards you. Pull belt to the right to remove the belt from the brush clutch axle.

Schritt 7  ¶ 

  • Pull the cover of the brush clutch belt out towards you.

  • Pull belt to the right to remove the belt from the brush clutch axle.

  • To reassemble your vacuum, pull the belt with your finger towards the axle. (Using a screwdriver, or a similar device, will delay access to the axle.)

Schritt 8  ¶ 

Insert a flat-head screwdriver into the two locking rings to remove the rings, which are located above the wheels on both sides. These rings secure the bottom assembly of the vacuum to the rest of the unit.

Schritt 8  ¶ 

  • Insert a flat-head screwdriver into the two locking rings to remove the rings, which are located above the wheels on both sides.

  • These rings secure the bottom assembly of the vacuum to the rest of the unit.

Schritt 9  ¶ 

Remove the four T15 torx screws that secure the motor housing to the vacuum. Remove the elbow-bend pipe on the right-side of the vacuum.

Schritt 9  ¶ 

  • Remove the four T15 torx screws that secure the motor housing to the vacuum.

  • Remove the elbow-bend pipe on the right-side of the vacuum.

  • Press the two release latches on either side of the elbow-bend pipe. Pull it out and away from the vacuum.

Schritt 10  ¶ 

Place the vacuum right-side up and leave it standing up.

Schritt 10  ¶ 

  • Place the vacuum right-side up and leave it standing up.

  • Remove the right side cover by pushing the release latch down while lifting the cover towards you.

Schritt 11  ¶ 

Set vacuum the on its back. Pull away the plastic cover of the motor housing.

Schritt 11  ¶ 

  • Set vacuum the on its back.

  • Pull away the plastic cover of the motor housing.

  • A bit of force may be needed.

Schritt 12  ¶ 

Insert flat head screwdriver between gray motor housing and black motor.

Schritt 12  ¶ 

  • Insert flat head screwdriver between gray motor housing and black motor.

  • Pry motor cover housing away.

Schritt 13  ¶ 

Release the motor assembly from its housing by strongly hitting the brush clutch axle with a hammer. The rubber grommets covering the motor may be greasy.

Schritt 13  ¶ 

  • Release the motor assembly from its housing by strongly hitting the brush clutch axle with a hammer.

  • The rubber grommets covering the motor may be greasy.

Schritt 14  ¶ 

Remove motor from housing slowly.

Schritt 14  ¶ 

  • Remove motor from housing slowly.

  • Do not pull the motor completely out of the housing. The motor is connected to the vacuum by two wires.

Schritt 15  ¶ 

Remove the power terminals from both sides of the motor. Do not pull by the wires when removing terminal. This can result in damage to your vacuum.

Schritt 15  ¶ 

  • Remove the power terminals from both sides of the motor.

  • Do not pull by the wires when removing terminal. This can result in damage to your vacuum.

  • These terminals will only fit one way (i.e. only one end is long enough to reach to the far side of the motor).

  • Remove the motor from the housing completely.

Schritt 16  ¶ 

Remove the two rubber grommets from your old motor, then transfer them to your new motor.

Schritt 16  ¶ 

  • Remove the two rubber grommets from your old motor, then transfer them to your new motor.