Zum Hauptinhalt wechseln
Hilfe

Ibanez 5 String Bass Model SR405QM Strings Replacement

Benötigt Bessere Bilder

Benötigt Bessere Bilder

Schönere Fotos werden diese Anleitung verbessern. Trage dazu bei, indem du die Alten bearbeitest oder Neue aufnimmst und hochlädst!

Fehler in den Markups

Fehler in den Markups

Diese Anleitung benötigt bessere Markups. Hilf aus, indem du sie korrigierst oder einige Markup-Anmerkungen erstellst.

This guide will show you how to replace old worn strings with a set of new strings in order to improve sound quality.

  • Autor: Vincent Nguyen
  • Geschätzte Zeit: 20 - 30 Minuten
  • Schwierigkeitsgrad: Einfach

Follow these steps to replace the stings on your Ibanez bass.

Werkzeuge
Relevante Ersatzteile

Schritt 1 Strings  ¶ 

Loosen all of the strings completely by turning each tuning peg counter clockwise. Continue until there is no tension in the strings

Schritt 1 Strings  ¶ 

  • Loosen all of the strings completely by turning each tuning peg counter clockwise. Continue until there is no tension in the strings

Schritt 2  ¶ 

Remove each string by pulling it out of the string tree at the top and through the bridge at the bottom.

Schritt 2  ¶ 

  • Remove each string by pulling it out of the string tree at the top and through the bridge at the bottom.

Schritt 3  ¶ 

Thread the largest new string through the bridge hole farthest from the knobs. Hold it firmly in place.

Schritt 3  ¶ 

  • Thread the largest new string through the bridge hole farthest from the knobs. Hold it firmly in place.

Schritt 4  ¶ 

Pull the string up to the corresponding string tree.

Schritt 4  ¶ 

  • Pull the string up to the corresponding string tree.

Schritt 5  ¶ 

Firmly grasp the middle of the string and pull it taut.

Schritt 5  ¶ 

  • Firmly grasp the middle of the string and pull it taut.

Schritt 6  ¶ 

On a taut string, measure one inch past the nut before using a pair of wire cutters to cut the string. On a taut string, measure one inch past the nut before using a pair of wire cutters to cut the string.

Schritt 6  ¶ 

  • On a taut string, measure one inch past the nut before using a pair of wire cutters to cut the string.

Schritt 7  ¶ 

Take the end of the string and insert it into the hole in the middle of the string tree.

Schritt 7  ¶ 

  • Take the end of the string and insert it into the hole in the middle of the string tree.

Schritt 8  ¶ 

Bend the string sideways into the channel of the string tree.

Schritt 8  ¶ 

  • Bend the string sideways into the channel of the string tree.

Schritt 9  ¶ 

Use one hand to maintain tension in the string by grabbing the string and rotating the hand toward the fret board.

Schritt 9  ¶ 

  • Use one hand to maintain tension in the string by grabbing the string and rotating the hand toward the fret board.

  • If tension is not retained it may result in uneven tension in the string tree, causing the tree to break.

Schritt 10  ¶ 

Rotate the tuning peg counterclockwise until the string is slightly taut, but not tight.

Schritt 10  ¶ 

  • Rotate the tuning peg counterclockwise until the string is slightly taut, but not tight.

  • Check to ensure that the string is lined up with the proper notch in the nut.

  • You will have proper alignment when the sting bends at a minimum angle.

Schritt 11  ¶ 

Repeat steps 3-10 for each string.

Schritt 11  ¶ 

  • Repeat steps 3-10 for each string.

  • Each string will progressively get closer to the knobs. It is not essential to progress from thick to thin strings, but it is important that they are connected to the proper string tree.

Schritt 12  ¶ 

Caution: Do not over tighten the strings. This can cause the strings to snap and could cause bodily injury. The strings are too tight when you have difficulty turning the tuning peg.

Schritt 12  ¶ 

  • Caution: Do not over tighten the strings. This can cause the strings to snap and could cause bodily injury. The strings are too tight when you have difficulty turning the tuning peg.

  • Tighten the string until it is close to the proper tuning. Use an electronic tuner or an online tuner that uses your computer's microphone. (Google: Online Tuner)

  • Note: Clockwise rotation of the tuning peg tightens the string and produces a higher pitch. Counter-clockwise rotation loosens the string causing a lower pitch.

  • Tune the thickest string to B, the second thickest string E, the next thickest to A, the next string to D, and the last string to G.

Schritt 13  ¶ 

Because the strings will change pitch as the guitar body deforms due to increased tension, repeat step 12 after each string is tuned individually.

Schritt 13  ¶ 

  • Because the strings will change pitch as the guitar body deforms due to increased tension, repeat step 12 after each string is tuned individually.