Zum Hauptinhalt wechseln
Hilfe

Toshiba Satellite C655D-S5084 Cooling Fan Replacement

Fehler in den Markups

Fehler in den Markups

Diese Anleitung benötigt bessere Markups. Hilf aus, indem du sie korrigierst oder einige Markup-Anmerkungen erstellst.

Unklarer Text

Unklarer Text

Teile des Textes dieser Anleitung sind verwirrend, doppelt oder vom Thema abweichend. Kläre das, indem du sie bearbeitest!

How to install a cooling fan in Toshiba Satellite C655D-S5084.

  • Autor: Shelby Kunz
  • Geschätzte Zeit: 25 - 35 Minuten
  • Schwierigkeitsgrad: Moderat

Is your computer getting too hot to handle? Overheating is a sign that your cooling fan may not be working properly, which may cause further damage to your computer. This guide will help you through the replacement of the cooling fan in your Toshiba Satellite C655D-S5084.

Abschnitte

Schritt 1 Cooling Fan  ¶ 

Remove the 5.5 mm "F5" screw with the Phillips #1 screwdriver and lift off plastic cover. Remove the 5.5 mm "F5" screw with the Phillips #1 screwdriver and lift off plastic cover.

Schritt 1 Cooling Fan  ¶ 

  • Remove the 5.5 mm "F5" screw with the Phillips #1 screwdriver and lift off plastic cover.

Schritt 2  ¶ 

Remove two 6.0 mm 'F6' screws with the Phillips #1 screwdriver.

Schritt 2  ¶ 

  • Remove two 6.0 mm 'F6' screws with the Phillips #1 screwdriver.

Schritt 3  ¶ 

Remove all fourteen (14) 6.0 mm 'F6' screws from the back panel using the Phillips #1 screwdriver.

Schritt 3  ¶ 

  • Remove all fourteen (14) 6.0 mm 'F6' screws from the back panel using the Phillips #1 screwdriver.

Schritt 4  ¶ 

Remove the two 6.0 mm golden 'F6' screws shown underneath the battery.

Schritt 4  ¶ 

  • Remove the two 6.0 mm golden 'F6' screws shown underneath the battery.

Schritt 5  ¶ 

Use a prying tool to release all three tabs underneath the battery.

Schritt 5  ¶ 

  • Use a prying tool to release all three tabs underneath the battery.

Schritt 6  ¶ 

Using a Phillips #1 screwdriver, remove two additional 2.0 mm screws underneath where the CD drive was.

Schritt 6  ¶ 

  • Using a Phillips #1 screwdriver, remove two additional 2.0 mm screws underneath where the CD drive was.

  • Then use a Phillips #1 screwdriver and a plastic opening tool to undo the two tabs in this location.

Schritt 7  ¶ 

Warning:  Opening your laptop like this may void the warranty.  These steps are difficult to undo, even with specialized tools.

Schritt 7  ¶ 

  • Warning: Opening your laptop like this may void the warranty. These steps are difficult to undo, even with specialized tools.

  • The base should be somewhat looser now. Work the slack around the base of the computer until all internal latches have been released.

Schritt 8  ¶ 

Using a small tool (or small hands) remove the tabs holding the white ribbon in place.

Schritt 8  ¶ 

  • Using a small tool (or small hands) remove the tabs holding the white ribbon in place.

Schritt 9  ¶ 

Remove the wide black ribbon in the same manner as in the previous step. There are also some catches that must be released.

Schritt 9  ¶ 

  • Remove the wide black ribbon in the same manner as in the previous step. There are also some catches that must be released.

Schritt 10  ¶ 

Remove the small white plug by firmly pulling on it.

Schritt 10  ¶ 

  • Remove the small white plug by firmly pulling on it.

Schritt 11  ¶ 

Remove the other white plug in the same manner as shown in the previous picture.

Schritt 11  ¶ 

  • Remove the other white plug in the same manner as shown in the previous picture.

Schritt 12  ¶ 

Remove the three 2.0 mm screws that are holding the fan in place.

Schritt 12  ¶ 

  • Remove the three 2.0 mm screws that are holding the fan in place.

Schritt 13  ¶ 

Remove the white plug attached to the cooling fan and then remove and clean.

Schritt 13  ¶ 

  • Remove the white plug attached to the cooling fan and then remove and clean.

  • Complete the previous steps in reverse order to reassemble and replace the cooling fan.