Zum Hauptinhalt wechseln
Hilfe

LG Escape (p870) Touch screen/digitizer Replacement

Anleitung eines Mitglieds

Anleitung eines Mitglieds

Ein großartiges Mitglied unserer Community hat diese Anleitung erstellt. Sie wird nicht von iFixit Mitarbeitern überprüft.

This guide will show you how to replace the touch screen/digitizer in your LG Escape (p870).

  • Autor: Brad
  • Geschätzte Zeit: 10 - 30 Minuten
  • Schwierigkeitsgrad: Moderat

Schritt 1 Touch screen/digitizer  ¶ 

Remove the remaining 6 screws securing the plastic frame to the back housing

Schritt 1 Touch screen/digitizer  ¶ 

  • Remove the remaining 6 screws securing the plastic frame to the back housing

Schritt 2  ¶ 

Insert a black plastic spudger or a small flathead screwdriver between the back silver bezel and the black area and begin prying the bezel away from the rest of the phone Continue working your way around the phone, prying carefully with your prying tool When you work the frame free, set it aside

Schritt 2  ¶ 

  • Insert a black plastic spudger or a small flathead screwdriver between the back silver bezel and the black area and begin prying the bezel away from the rest of the phone

  • Continue working your way around the phone, prying carefully with your prying tool

  • When you work the frame free, set it aside

Schritt 3  ¶ 

Wifi and cell service antennas

Schritt 3  ¶ 

  • Wifi and cell service antennas

  • LCD connector

  • Back camera connector

  • Front camera connector

  • Touch screen/ digitizer connector

  • Charger port connector

  • Headphone jack connector

Schritt 4  ¶ 

With a spudger or safe open pry tool, carefully detach the LCD flex connector Release the two antennae from their connectors Release the back camera's flex from its connector

Schritt 4  ¶ 

  • With a spudger or safe open pry tool, carefully detach the LCD flex connector

  • Release the two antennae from their connectors

  • Release the back camera's flex from its connector

Schritt 5  ¶ 

Release the charging port flex from its connector Release the front camera's flex from its connector

Schritt 5  ¶ 

  • Release the charging port flex from its connector

  • Release the front camera's flex from its connector

  • Release the touch screen/digitizer's flex cable from its connector

Schritt 6  ¶ 

Release the headphone jack's flex cable from its connector

Schritt 6  ¶ 

  • Release the headphone jack's flex cable from its connector

Schritt 7  ¶ 

With a pair of tweezers, VERY carefully pull the volume button flex out of the rear housing Repeat the process with the power button flex cable

Schritt 7  ¶ 

  • With a pair of tweezers, VERY carefully pull the volume button flex out of the rear housing

  • Repeat the process with the power button flex cable

  • The power button and volume button flex cables will tear very easily, so be cautious

Schritt 8  ¶ 

Lift the motherboard away from the housing, taking extra care not to snag any of the antennae or flex cables Set the motherboard aside

Schritt 8  ¶ 

  • Lift the motherboard away from the housing, taking extra care not to snag any of the antennae or flex cables

  • Set the motherboard aside

Schritt 9  ¶ 

Insert a small flathead screwdriver or black plastic spudger between the front silver bezel and the black plastic mid-frame Gently pry on the bezel to release the clips adhering the screen to the mid-frame

Schritt 9  ¶ 

  • Insert a small flathead screwdriver or black plastic spudger between the front silver bezel and the black plastic mid-frame

  • Gently pry on the bezel to release the clips adhering the screen to the mid-frame

  • Work your way around the phone, still using the small flathead or spudger, until the screen is fully separated

  • Remove the screen, taking care not to tear the flex cable that is still threaded through the housing.

  • After carefully threading the digitizer and outer housing/bezel from the middle bracket you'll notice the digitizer is held on by a band of very strong adhesive - this will be destroyed when you take off the old digitizer. When you replace your digitizer you can use double-sided tape or epoxy to hold the new digitizer on the bezel.