Zum Hauptinhalt wechseln
Hilfe

iPod Nano 7th Generation Front Panel Assembly Replacement

Nicht eigenständige Anleitung

Nicht eigenständige Anleitung

Bitte beachte, dass diese Anleitung nur eine grundständige Anleitung für andere Anleitungen ist.

Prerequisite to replace the front panel assembly.

Schritt 1 Front Panel Assembly  ¶ 

Lay the iOpener over the plastic tab to loosen the adhesive. Let the bag sit on the device for approximately 90 seconds before attempting to open the panel. Lay the iOpener over the plastic tab to loosen the adhesive. Let the bag sit on the device for approximately 90 seconds before attempting to open the panel.

Schritt 1 Front Panel Assembly  ¶ 

  • Lay the iOpener over the plastic tab to loosen the adhesive. Let the bag sit on the device for approximately 90 seconds before attempting to open the panel.

Schritt 2  ¶ 

Use a plastic opening tool to pull the rear plastic cover away from the device until there is enough room to insert a spudger. Insert a spudger under the cover, then pry it up and away from the device. Remove the rear plastic cover from the iPod.

Schritt 2  ¶ 

  • Use a plastic opening tool to pull the rear plastic cover away from the device until there is enough room to insert a spudger.

  • Insert a spudger under the cover, then pry it up and away from the device.

  • Remove the rear plastic cover from the iPod.

  • Be very careful in removing the plastic cover as the bluetooth antenna is adhered to it.

Schritt 3  ¶ 

Gently bend the Bluetooth antenna to the right, out of the way of the screws in the bottom of the device.

Schritt 3  ¶ 

  • Gently bend the Bluetooth antenna to the right, out of the way of the screws in the bottom of the device.

  • Remove the single 1.4 mm Phillips #000 screw from the black plastic spacer.

Schritt 4  ¶ 

Use a plastic opening tool to remove the black plastic spacer from the Nano. Use a plastic opening tool to remove the black plastic spacer from the Nano.

Schritt 4  ¶ 

  • Use a plastic opening tool to remove the black plastic spacer from the Nano.

Schritt 5  ¶ 

Remove the two 2 mm Phillips #000 screws from the bottom of the case.

Schritt 5  ¶ 

  • Remove the two 2 mm Phillips #000 screws from the bottom of the case.

Schritt 6  ¶ 

Insert a plastic opening tool into the seam between the white plastic front panel and the rear case. Slide the opening tool along the edge of the front panel to free it from clips and adhesive.

Schritt 6  ¶ 

  • Insert a plastic opening tool into the seam between the white plastic front panel and the rear case.

  • Slide the opening tool along the edge of the front panel to free it from clips and adhesive.

Schritt 7  ¶ 

Use a spudger to press the midframe screw tab up and out of the rear case.

Schritt 7  ¶ 

  • Use a spudger to press the midframe screw tab up and out of the rear case.

Schritt 8  ¶ 

Use a metal spudger to carefully pry near the Lightning connector and under all parts of the front panel assembly: the front glass/digitizer, the LCD display and the metal midframe.

Schritt 8  ¶ 

  • Use a metal spudger to carefully pry near the Lightning connector and under all parts of the front panel assembly: the front glass/digitizer, the LCD display and the metal midframe.

  • The adhesive under the metal midframe/display assembly is quite strong and the components are fragile, so go slowly and gently. Make sure you do not bend the LCD screen.

Schritt 9  ¶ 

Continue prying along the edges under the front panel assembly, releasing the clips and adhesive along the sides of the device. Continue prying along the edges under the front panel assembly, releasing the clips and adhesive along the sides of the device.

Schritt 9  ¶ 

  • Continue prying along the edges under the front panel assembly, releasing the clips and adhesive along the sides of the device.

Schritt 10  ¶ 

Pull the front panel assembly slightly down and partially out of the device. You only need to open the device enough to gain access to the display cable connectors near the sleep/power button.

Schritt 10  ¶ 

  • Pull the front panel assembly slightly down and partially out of the device.

  • You only need to open the device enough to gain access to the display cable connectors near the sleep/power button.

  • Do not separate the two halves entirely, they are still connected by several cables.

Schritt 11  ¶ 

Use a spudger to release the digitizer cable and display data cable connectors. Use a spudger to release the digitizer cable and display data cable connectors.

Schritt 11  ¶ 

  • Use a spudger to release the digitizer cable and display data cable connectors.

Schritt 12  ¶ 

Gently unfold the two halves of the device to access the internal components.

Schritt 12  ¶ 

  • Gently unfold the two halves of the device to access the internal components.

  • Do not try to completely separate the two sections, yet, as they are still attached via a soldered cable.

Schritt 13  ¶ 

Pull up on the battery pull tab to free the battery from its adhesive. Flip the battery over into the rear case for safekeeping.

Schritt 13  ¶ 

  • Pull up on the battery pull tab to free the battery from its adhesive.

  • Flip the battery over into the rear case for safekeeping.

Schritt 14  ¶ 

Completely separate the front panel assembly from the rest of the device.

Schritt 14  ¶ 

  • Completely separate the front panel assembly from the rest of the device.